I.S. EN IEC 61730-2:2018
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PHOTOVOLTAIC (PV) MODULE SAFETY QUALIFICATION - PART 2: REQUIREMENTS FOR TESTING
Hardcopy , PDF
01-27-2020
05-15-2018
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
National Foreword
FOREWORD
1 Scope
2 Normative references
3 Terms and definitions
4 Test categories
5 Classes and their necessary test procedures
6 Sampling
7 Test report
8 Testing
9 Pass criteria
10 Test procedures
Annex A (informative) - Recommendations for testing
of PV modules from production
Annex B (informative) - Fire tests, spread-of-flame and
burning-brand tests for PV modules
Annex ZA (normative) - Normative references to
international publications with their
corresponding European publications
Annex ZZ (informative) - Relationship between
this European standard and the safety
objectives of Directive 2014/35/EU [2014 OJ L96]
aimed to be covered
Defines the testing sequence intended to verify the safety of PV modules whose construction has been assessed by IEC 61730-1.
| Committee |
TC 82
|
| DevelopmentNote |
Supersedes I.S. EN 61730-2. For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (05/2018)
|
| DocumentType |
Standard
|
| ISBN |
978-2-8322-3575-1
|
| Pages |
132
|
| ProductNote |
The date of any NSAI previous adoption may not match the date of its original CEN/CENELEC document.
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| IEC 61730-2:2016 | Identical |
| EN IEC 61730-2:2018 | Identical |
| IEC 60950-1:2005+AMD1:2009+AMD2:2013 CSV | Information technology equipment - Safety - Part 1: General requirements |
| ISO/IEC 17025:2005 | General requirements for the competence of testing and calibration laboratories |
| EN 60904-2:2015 | Photovoltaic devices - Part 2: Requirements for photovoltaic reference devices |
| EN 60904-9 : 2007 | PHOTOVOLTAIC DEVICES - PART 9: SOLAR SIMULATOR PERFORMANCE REQUIREMENTS |
| ANSI Z97.1 : 2015 | SAFETY GLAZING MATERIALS USED IN BUILDINGS - SAFETY PERFORMANCE SPECIFICATIONS AND METHODS OF TEST |
| ISO 813:2016 | Rubber, vulcanized or thermoplastic Determination of adhesion to a rigid substrate 90 degree peel method |
| IEC 60904-9:2007 | Photovoltaic devices - Part 9: Solar simulator performance requirements |
| EN 60068-2-1:2007 | Environmental testing - Part 2-1: Tests - Test A: Cold |
| ISO 23529:2016 | Rubber General procedures for preparing and conditioning test pieces for physical test methods |
| EN 60068-2-2:2007 | Environmental testing - Part 2-2: Tests - Test B: Dry heat |
| EN 60060-1:2010 | High-voltage test techniques - Part 1: General definitions and test requirements |
| ISO 8124-1:2014 | Safety of toys Part 1: Safety aspects related to mechanical and physical properties |
| EN 60950-1:2006/A2:2013 | INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60950-1:2005/A2:2013, MODIFIED) |
| EN 61730-1:2007/A11:2014 | PHOTOVOLTAIC (PV) MODULE SAFETY QUALIFICATION - PART 1: REQUIREMENTS FOR CONSTRUCTION (IEC 61730-1:2004, MODIFIED) |
| ISO 11925-2:2010 | Reaction to fire tests Ignitability of products subjected to direct impingement of flame Part 2: Single-flame source test |
| EN 60068-3-5:2002 | Environmental testing - Part 3-5: Supporting documentation and guidance - Confirmation of the performance of temperature chambers |
| IEC 60904-2:2015 RLV | Photovoltaic devices - Part 2: Requirements for photovoltaic reference devices |
| ISO 4587:2003 | Adhesives Determination of tensile lap-shear strength of rigid-to-rigid bonded assemblies |
| IEC 60068-3-5:2001 | Environmental testing - Part 3-5: Supporting documentation and guidance - Confirmation of the performance of temperature chambers |
| EN 60695-2-10:2013 | Fire hazard testing - Part 2-10: Glowing/hot-wire based test methods - Glow-wire apparatus and common test procedure |
| IEC 61730-1:2016 | Photovoltaic (PV) module safety qualification - Part 1: Requirements for construction |
| IEC 60068-2-2:2007 | Environmental testing - Part 2-2: Tests - Test B: Dry heat |
| EN 61032:1998 | Protection of persons and equipment by enclosures - Probes for verification |
| IEC 60598-1:2014+AMD1:2017 CSV | Luminaires - Part 1: General requirements and tests |
| EN 60664-1:2007 | Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests |
| ISO 5893:2002 | Rubber and plastics test equipment Tensile, flexural and compression types (constant rate of traverse) Specification |
| EN 61140:2016 | Protection against electric shock - Common aspects for installation and equipment |
| IEC 60068-2-1:2007 | Environmental testing - Part 2-1: Tests - Test A: Cold |
| EN 61010-1:2010 | Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 1: General requirements |
| ISO 4046-4:2002 | Paper, board, pulps and related terms Vocabulary Part 4: Paper and board grades and converted products |
| IEC 60060-1:2010 | High-voltage test techniques - Part 1: General definitions and test requirements |
| EN 62790:2015 | Junction boxes for photovoltaic modules - Safety requirements and tests |
| IEC 61140:2016 | Protection against electric shock - Common aspects for installation and equipment |
| IEC 61032:1997 | Protection of persons and equipment by enclosures - Probes for verification |
| IEC 60695-2-10:2013 | Fire hazard testing - Part 2-10: Glowing/hot-wire based test methods - Glow-wire apparatus and common test procedure |
| IEC 61010-1:2010+AMD1:2016 CSV | Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 1: General requirements |
| IEC 60664-1:2007 | Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.