I.S. EN 89:2015
Current
The latest, up-to-date edition.
GAS-FIRED STORAGE WATER HEATERS FOR THE PRODUCTION OF DOMESTIC HOT WATER
Hardcopy , PDF
English
01-01-2015
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Classification of storage water heaters
5 Construction requirement
6 Operational requirements
7 Rational use of energy
8 Fitness for purpose
9 Marking and instructions
10 Ecodesign Data
11 Energy Labelling Data
12 Figures referenced in this standard
Annex A (informative) - National situations
Annex B (normative) - Test apparatus for type C[11]
appliances
Annex C (normative) - Test apparatus for type C[21]
appliances
Annex D (informative) - Examples of composition of the gas
circuit
Annex E (normative) - Soundness test - Volumetric method
Annex F (informative) - Guidelines for extension to other
categories
Annex G (informative) - A-deviations
Annex H (informative) - NO[x] conversion calculation
Annex I (informative) - Requirements and test methods for
separate air supply and combustion products evacuation
ducts of type C6 water heaters
Annex J (normative) - Lists of materials currently used
Annex K (normative) - Test methods to determine the effects
of to long-term thermal load, longterm condensate
exposure, condensing/non-condensing cycling and
resistance to UV radiation
Annex L (normative) - Parts in copper or copper alloys
Annex M (informative) - Compilation of the test conditions for
the various gas families
Annex N (informative) - Alternative Method for the determination
of the nominal heat input or the maximum and minimum
heat input (according to 6.3.1) for appliances using
a pneumatic gas/air ratio control system
Annex ZA (informative) - Clauses of this European Standard
addressing essential requirements or other
provisions of UE Directives
Annex ZB (informative) - Relationship between this European
Standard and the requirements of Commission
Regulation (EU) No 814/2013
Annex ZC (informative) - Relationship between this European
Standard and the requirements of Commission
Delegated Regulation (EU) No 812/2013
Bibliography
Specifies the specifications and test methods for the construction, safety, rational use of energy and fitness for purpose, environment and classification and marking of gas-fired storage water heaters for domestic hot water uses, hereafter called 'appliance'.
| DevelopmentNote |
Supersedes I.S. 805-1 & 2 (01/2005)
|
| DocumentType |
Standard
|
| Pages |
162
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| DIN EN 89:2015-08 | Identical |
| BS EN 89:2015 | Identical |
| UNI EN 89 : 2008 | Identical |
| SN EN 89:2015 | Identical |
| NS EN 89 : 1999 | Identical |
| UNE-EN 89:2016 | Identical |
| NEN EN 89 : 2015 | Identical |
| EN 89:2015 | Identical |
| NBN EN 89 : 2015 | Identical |
| EN 1859:2009+A1:2013 | Chimneys - Metal chimneys - Test methods |
| IEC 60335-2-102:2004+AMD1:2008+AMD2:2012 CSV | Household and similar electrical appliances - Safety - Part 2-102:Particular requirements for gas, oil and solid-fuel burning appliances having electrical connections |
| IEC 60730-2-9:2015 RLV | Automatic electrical controls - Part 2-9: Particular requirements for temperature sensing controls |
| EN ISO 8256:2004 | Plastics - Determination of tensile-impact strength (ISO 8256:2004) |
| EN 1057:2006+A1:2010 | Copper and copper alloys - Seamless, round copper tubes for water and gas in sanitary and heating applications |
| ISO 815-1:2014 | Rubber, vulcanized or thermoplastic Determination of compression set Part 1: At ambient or elevated temperatures |
| EN 1490:2000 | Building valves - Combined temperature and pressure relief valves - Tests and requirements |
| EN 60730-2-9:2010 | Automatic electrical controls for household and similar use - Part 2-9: Particular requirements for temperature sensing controls |
| EN ISO 527-2:2012 | Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics (ISO 527-2:2012) |
| EN 13203-1:2015 | Gas fired domestic appliances producing hot water - Part 1: Assessment of performance of hot water deliveries |
| EN 13216-1:2004 | Chimneys - Test methods for system chimneys - Part 1: General test methods |
| ISO 188:2011 | Rubber, vulcanized or thermoplastic — Accelerated ageing and heat resistance tests |
| EN 13203-2:2015 | Gas-fired domestic appliances producing hot water - Part 2: Assessment of energy consumption |
| ISO 8256:2004 | Plastics — Determination of tensile-impact strength |
| EN ISO 3166-1:2014 | Codes for the representation of names of countries and their subdivisions - Part 1: Country codes (ISO 3166-1:2013) |
| EN ISO 527-1:2012 | Plastics - Determination of tensile properties - Part 1: General principles (ISO 527-1:2012) |
| EN ISO 179-1:2010 | Plastics - Determination of Charpy impact properties - Part 1: Non-instrumented impact test (ISO 179-1:2010) |
| EN 161:2011+A3:2013 | Automatic shut-off valves for gas burners and gas appliances |
| ISO 527-2:2012 | Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics |
| EN ISO 228-1:2003 | Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000) |
| EN 14241-1:2013 | Chimneys - Elastomeric seals and elastomeric sealants - Material requirements and test methods - Part 1: Seals in flue liners |
| ISO 1183:1987 | Plastics Methods for determining the density and relative density of non-cellular plastics |
| ISO 262:1998 | ISO general purpose metric screw threads — Selected sizes for screws, bolts and nuts |
| EN 14459:2015 | Safety and control devices for burners and appliances burning gaseous or liquid fuels - Control functions in electronic systems - Methods for classification and assessment |
| EN 1487:2014 | Building valves - Hydraulic safety groups - Tests and requirements |
| EN 437:2003+A1:2009 | Test gases - Test pressures - Appliance categories |
| EN 125:2010+A1:2015 | Flame supervision devices for gas burning appliances - Thermoelectric flame supervision devices |
| ISO 7619:1997 | Rubber Determination of indentation hardness by means of pocket hardness meters |
| EN 126:2012 | Multifunctional controls for gas burning appliances |
| CEN/TR 1749:2014 | European scheme for the classification of gas appliances according to the method of evacuation of the combustion products (types) |
| CR 1404:1994 | Determination of emissions from appliances burning gaseous fuels during type-testing |
| EN ISO 9969:2016 | Thermoplastics pipes - Determination of ring stiffness (ISO 9969:2016) |
| EN 60335-2-102:2016 | Household and similar electrical appliances - Safety - Part 2-102: Particular requirements for gas, oil and solid-fuel burning appliances having electrical connections |
| ISO 6914:2013 | Rubber, vulcanized or thermoplastic Determination of ageing characteristics by measurement of stress relaxation in tension |
| EN 14471:2013+A1:2015 | Chimneys - System chimneys with plastic flue liners - Requirements and test methods |
| ISO 179-1:2010 | Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test |
| ISO 3166-1:2013 | Codes for the representation of names of countries and their subdivisions Part 1: Country codes |
| EN 60335-1:2012/A13:2017 | HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60335-1:2010, MODIFIED) |
| ISO 37:2017 | Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties |
| EN 298:2012 | Automatic burner control systems for burners and appliances burning gaseous or liquid fuels |
| EN 1856-1:2009 | Chimneys - Requirements for metal chimneys - Part 1: System chimney products |
| EN 549:1994 | Rubber materials for seals and diaphragms for gas appliances and gas equipment |
| ISO 301:2006 | Zinc alloy ingots intended for castings |
| EN 10226-1:2004 | Pipe threads where pressure tight joints are made on the threads - Part 1: Taper external threads and parallel internal threads - Dimensions, tolerances and designation |
| ISO 178:2010 | Plastics Determination of flexural properties |
| ISO 9969:2016 | Thermoplastics pipes Determination of ring stiffness |
| EN 513:1999 | Unplasticized polyvinylchloride (PVC-U) profiles for the fabrication of windows and doors - Determination of the resistance to artificial weathering |
| EN 88-1:2011+A1:2016 | Pressure regulators and associated safety devices for gas appliances - Part 1: Pressure regulators for inlet pressures up to and including 50 kPa |
| ISO 228-1:2000 | Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation |
| EN 573-1:2004 | Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 1: Numerical designation system |
| ISO 527-1:2012 | Plastics Determination of tensile properties Part 1: General principles |
| ISO 1817:2015 | Rubber, vulcanized or thermoplastic Determination of the effect of liquids |
| EN 10088-1:2014 | Stainless steels - Part 1: List of stainless steels |
| ISO 2781:2008 | Rubber, vulcanized or thermoplastic Determination of density |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.