I.S. EN 840-3:2012
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
MOBILE WASTE AND RECYCLING CONTAINERS - PART 3: CONTAINERS WITH 4 WHEELS WITH A CAPACITY UP TO 1300 L WITH DOME LID(S), FOR TRUNNION AND/OR COMB LIFTING DEVICES - DIMENSIONS AND DESIGN
Hardcopy , PDF
05-06-2020
English
01-01-2012
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Volumes
5 Dimensions and design
6 Nominal mass
7 Safety and health requirements
8 Testing
9 Marking
10 Designation
Annex A (informative) - Recommendations for
manufacturers of lifting devices
Annex B (informative) - A-Deviations
Bibliography
Describes dimensions and design requirements of mobile waste and recycling containers with 4 wheels, with dome lid(s) and capacity up to 1300 l to be used by trunnion and/or comb lifting device.
| DocumentType |
Standard
|
| Pages |
22
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| ONORM EN 840-3 : 2013 | Identical |
| NEN EN 840-3 : 2012 | Identical |
| BS EN 840-3:2012 | Identical |
| SN EN 840-3 : 2013 | Identical |
| NBN EN 840-3 : 2013 | Identical |
| EN 840-3:2012 | Identical |
| UNI EN 840-3 : 2013 | Identical |
| UNE-EN 840-3:2013 | Identical |
| NS EN 840-3 : 2012 | Identical |
| NF EN 840-3 : 2013 | Identical |
| DIN EN 840-3:2013-03 | Identical |
| EN 1501-2:2005+A1:2009 | Refuse collection vehicles and associated lifting devices - General requirements and safety requirements - Part 2: Side loaded refuse collection vehicles |
| EN 1501-5:2011 | Refuse collection vehicles - General requirements and safety requirements - Part 5: Lifting devices for refuse collection vehicles |
| ISO 11469:2016 | Plastics — Generic identification and marking of plastics products |
| EN 1501-3:2008 | Refuse collection vehicles and their associated lifting devices - General requirements and safety requirements - Part 3: Front loaded refuse collection vehicles |
| EN ISO 11469:2016 | Plastics - Generic identification and marking of plastics products (ISO 11469:2016) |
| EN 1501-1:2011+A1:2015 | Refuse collection vehicles - General requirements and safety requirements - Part 1: Rear loaded refuse collection vehicles |
| EN 840-1:2012 | Mobile waste and recycling containers - Part 1: Containers with 2 wheels with a capacity up to 400 l for comb lifting devices - Dimensions and design |
| EN 14803:2006 | Identification and/or determination of the quantity of waste |
| EN 840-2:2012 | Mobile waste and recycling containers - Part 2: Containers with 4 wheels with a capacity up to 1 300 l with flat lid(s), for trunnion and/or comb lifting devices - Dimensions and design |
| EN 840-5:2012 | Mobile waste and recycling containers - Part 5: Performance requirements and test methods |
| EN 840-6:2012 | Mobile waste and recycling containers - Part 6: Safety and health requirements |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.