I.S. EN 818-3:1999
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
SHORT LINK CHAIN FOR LIFTING PURPOSES - SAFETY - PART 3: MEDIUM TOLERANCE CHAIN FOR CHAIN SLINGS - GRADE 4
Hardcopy , PDF
06-25-2008
English
09-24-1999
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Hazards
5 Safety requirements
5.1 General
5.2 Dimensions
5.2.1 Nominal size of chain, d[n]
5.2.2 Tolerance on material diameter (except at the weld)
5.2.3 Weld diameter
5.2.4 Length dimensionally affected by welding
5.2.5 Pitch and widths
5.3 Materials and heat treatment
5.3.1 General
5.3.2 Quality of material
5.3.3 Heat treatment
5.3.4 Stainless steel
5.4 Mechanical properties
5.4.1 Manufacturing proof force (MPF)
5.4.2 Breaking force (BF) and total ultimate elongation (A)
5.4.3 Bend deflection
6 Verification of safety requirements
6.1 Qualification of personnel
6.2 Size of lot and selection of samples
6.3 Manufacturing proof force, breaking force and total
ultimate elongation
6.3.1 Static tensile test
6.3.2 Manufacturing proof force acceptance criteria
6.3.3 Breaking force and total ultimate elongation
acceptance criteria
6.4 Bend deflection
6.4.1 Bend test
6.4.2 Bend deflection acceptance criteria
7 Marking
8 Manufacturer's certificate
9 Information for use
Annex A (informative) Calculation of dimensions, working
load limits and mechanical properties
A.1 Dimensions and tolerances
A.2 Working load limits and mechanical properties
Annex B (informative) Mass of chain
Annex C (informative) Designation system for chain (medium
tolerance) - Grade 4
Annex ZA (informative) Relationship between this European
Standard and the Essential Requirements of EU
Directive 98/37/EC
Annex ZB (informative) Relationship between this European
Standard and the Essential Requirements of EU
Directive 2006/42/EC
Bibliography
Describes the requirements related to safety for short link chains, grade 4, of medium tolerance for use in chain slings to EN 818-4:1996+A1 and for general lifting purposes.
| DevelopmentNote |
1999 Edition Re-Issued in June 2008 & incorporates AMD 1 2008. (07/2008)
|
| DocumentType |
Standard
|
| Pages |
23
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Withdrawn
|
| Standards | Relationship |
| UNI EN 818-3 : 2008 | Identical |
| NBN EN 818-3 : 1999 + A1 2008 | Identical |
| EN 818-3:1999+A1:2008 | Identical |
| NS EN 818-3 : 1999 + A1 2008 | Identical |
| NEN EN 818-3 : 1999 + A1 2008 | Identical |
| NF EN 818-3 : 1999 + A1 2008 | Identical |
| BS EN 818-3 : 1999 | Identical |
| SN EN 818-3 : 1999 + A1 2008 | Identical |
| DIN EN 818-3:2008-12 | Identical |
| EN 10088-3:2014 | Stainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes |
| EN 1050 : 1996 | SAFETY OF MACHINERY - PRINCIPLES FOR RISK ASSESSMENT |
| ISO 12100-2:2003 | Safety of machinery Basic concepts, general principles for design Part 2: Technical principles |
| ISO 643:2012 | Steels Micrographic determination of the apparent grain size |
| ISO 497:1973 | Guide to the choice of series of preferred numbers and of series containing more rounded values of preferred numbers |
| ISO 12100-1:2003 | Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology |
| EN 818-6:2000+A1:2008 | Short link chain for lifting purposes - Safety - Part 6: Chain slings - Specification for information for use and maintenance to be provided by the manufacturer |
| EN 818-1:1996+A1:2008 | Short link chain for lifting purposes - Safety - Part 1: General conditions of acceptance |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.