I.S. EN 61400-3:2009
Current
The latest, up-to-date edition.
WIND TURBINES - PART 3: DESIGN REQUIREMENTS FOR OFFSHORE WIND TURBINES
Hardcopy , PDF
English
01-01-2009
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 Principal elements
6 External conditions
7 Structural design
8 Control and protection system
9 Mechanical systems
10 Electrical system
11 Foundation design
12 Assessment of the external conditions at an offshore
wind turbine site
13 Assembly, installation and erection
14 Commissioning, operation and maintenance
Annex A (informative) - Key design parameters for an offshore
wind turbine
Annex B (informative) - Wave spectrum formulations
Annex C (informative) - Shallow water hydrodynamics and breaking
waves
Annex D (informative) - Guidance on calculation of hydrodynamic
loads
Annex E (informative) - Recommendations for design of offshore
wind turbine support structures with respect to ice loads
Annex F (informative) - Offshore wind turbine foundation design
Annex G (informative) - Statistical extrapolation of operational
metocean parameters for ultimate strength analysis
Annex H (informative) - Corrosion protection
Bibliography
Annex ZA (normative) - Normative references to international
publications with their corresponding European
publications
Describes additional requirements for assessment of the external conditions at an offshore wind turbine site and it specifies essential design requirements to ensure the engineering integrity of offshore wind turbines.
| DevelopmentNote |
For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
|
| DocumentType |
Standard
|
| Pages |
132
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Current
|
| Standards | Relationship |
| EN 61400-3:2009 | Identical |
| IEC 61400-3:2009 | Identical |
| IEC 60038:2009 | IEC standard voltages |
| EN ISO 19901-1:2015 | Petroleum and natural gas industries - Specific requirements for offshore structures - Part 1: Metocean design and operating considerations (ISO 19901-1:2015) |
| ISO 19900:2013 | Petroleum and natural gas industries General requirements for offshore structures |
| IEC 60898:1995 | Electrical accessories - Circuit-breakers for overcurrent protection for household and similar installations |
| ISO 3010:2017 | Bases for design of structures — Seismic actions on structures |
| IEC TR 61400-24:2002 | Wind turbine generator systems - Part 24: Lightning protection |
| IEC 61310-2:2007 | Safety of machinery - Indication, marking and actuation - Part 2: Requirements for marking |
| EN 62305-4:2011/AC:2016 | PROTECTION AGAINST LIGHTNING - PART 4: ELECTRICAL AND ELECTRONIC SYSTEMS WITHIN STRUCTURES (IEC 62305-4:2010) |
| EN ISO 19901-4:2016 | Petroleum and natural gas industries - Specific requirements for offshore structures - Part 4: Geotechnical and foundation design considerations (ISO 19901-4:2016) |
| API 2N : 2015 | PLANNING, DESIGNING, AND CONSTRUCTING STRUCTURES AND PIPELINES FOR ARCTIC CONDITIONS |
| ISO 4354:2009 | Wind actions on structures |
| IEC 60204-1:2016 | Safety of machinery - Electrical equipment of machines - Part 1: General requirements |
| ISO 2394:2015 | General principles on reliability for structures |
| IEC 60204-11:2000 | Safety of machinery - Electrical equipment of machines - Part 11: Requirements for HV equipment for voltages above 1 000 V a.c. or 1 500 V d.c. and not exceeding 36 kV |
| IEC TS 61400-13:2001 | Wind turbine generator systems - Part 13: Measurement of mechanical loads |
| ISO 2533:1975 | Standard Atmosphere |
| ISO 19903:2006 | Petroleum and natural gas industries Fixed concrete offshore structures |
| NACE RP 01 76 : 2003 | CORROSION CONTROL OF STEEL FIXED OFFSHORE STRUCTURES ASSOCIATED WITH PETROLEUM PRODUCTION |
| HD 478.2.1 : 200S1 | CLASSIFICATION OF ENVIRONMENTAL CONDITIONS - ENVIRONMENTAL CONDITIONS APPEARING IN NATURE - TEMPERATURE AND HUMIDITY |
| API 2A : 1986 | RECOMMENDED PRACTICE FOR PLANNING, DESIGNING AND CONSTRUCTING FIXED OFFSHORE PLATFORMS |
| EN 61400-1:2005/A1:2010 | WIND TURBINES - PART 1: DESIGN REQUIREMENTS |
| ISO 19901-4:2016 | Petroleum and natural gas industries Specific requirements for offshore structures Part 4: Geotechnical and foundation design considerations |
| ISO 13819-2:1995 | Petroleum and natural gas industries Offshore structures Part 2: Fixed steel structures |
| IEC 60721-2-1:2013 | Classification of environmental conditions - Part 2-1: Environmental conditions appearing in nature - Temperature and humidity |
| EN ISO 19903:2006 | Petroleum and natural gas industries - Fixed concrete offshore structures (ISO 19903:2006) |
| EN 62305-3:2011 | Protection against lightning - Part 3: Physical damage to structures and life hazard |
| ISO 19902:2007 | Petroleum and natural gas industries Fixed steel offshore structures |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| IEC 60755:2017 | General safety requirements for residual current operated protective devices |
| ISO 9001:2015 | Quality management systems — Requirements |
| ISO 8930:1987 | General principles on reliability for structures List of equivalent terms |
| IEC 62305-4:2010 | Protection against lightning - Part 4: Electrical and electronic systems within structures |
| IEC 61310-1:2007 | Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals |
| IEC 60173:1964 | Colours of the cores of flexible cables and cords |
| ISO 19901-1:2015 | Petroleum and natural gas industries Specific requirements for offshore structures Part 1: Metocean design and operating considerations |
| EN ISO 19900:2013 | Petroleum and natural gas industries - General requirements for offshore structures (ISO 19900:2013) |
| IEC 61400-1:2005+AMD1:2010 CSV | Wind turbines - Part 1: Design requirements |
| IEC 62305-3:2010 | Protection against lightning - Part 3: Physical damage to structures and life hazard |
| IEC 61400-21:2008 | Wind turbines - Part 21: Measurement and assessment of power quality characteristics of grid connected wind turbines |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.