I.S. EN 61347-2-13:2014
Current
The latest, up-to-date edition.
LAMP CONTROLGEAR - PART 2-13: PARTICULAR REQUIREMENTS FOR D.C. OR A.C. SUPPLIED ELECTRONIC CONTROLGEAR FOR LED MODULES
Hardcopy , PDF
English
01-01-2014
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
National Foreword
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 General requirements
5 General notes on tests
6 Classification
7 Marking
8 Protection against accidental contact with live parts
9 Terminals
10 Provisions for protective earthing
11 Moisture resistance and insulation
12 Electric strength
13 Thermal endurance test for windings of ballasts
14 Fault conditions
15 Transformer heating
16 Construction
17 Creepage distances and clearances
18 Screws, current-carrying parts and connections
19 Resistance to heat, fire and tracking
20 Resistance to corrosion
21 Maximum working voltage (U[out]) in any load condition
Annex A (normative) - Test to establish whether a
conductive part is a live part which may cause
an electric shock
Annex B (normative) - Particular requirements for
thermally protected lamp controlgear
Annex C (normative) - Particular requirements for
electronic lamp controlgear with means of
protection against overheating
Annex D (normative) - Requirements for carrying out
the heating tests of thermally protected lamp
controlgear
Annex E (normative) - Use of constant S other than
4500 in t[w] tests
Annex F (normative) - Draught-proof enclosure
Annex G (normative) - Explanation of the derivation of the
values of pulse voltages
Annex H (normative) - Tests
Annex I (normative) - Particular additional requirements
for SELV d.c. or a.c. supplied electronic controlgear
for LED modules
Annex J (normative) - Particular additional safety
requirements for a.c., a.c./d.c. or d.c supplied
electronic controlgear for emergency lighting
Bibliography
Annex ZA (normative) - Normative references to
international publications with their
corresponding European publications
Describes particular safety requirements for electronic controlgear for use on d.c. or a.c. supplies up to 1000 V (a.c. at 50 Hz or 60 Hz) and at an output frequency which can deviate from the supply frequency, associated with LED modules.
| DevelopmentNote |
For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
|
| DocumentType |
Standard
|
| Pages |
76
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Current
|
| Standards | Relationship |
| SN EN 61347-2-13 : 2014 AMD 1 2017 | Identical |
| NBN EN 61347-2-13 : 2014 | Identical |
| BS EN 61347-2-13 : 2014 | Identical |
| DIN EN 61347-2-13 : 2017 | Identical |
| EN 61347-2-13:2014/A1:2017 | Identical |
| NF EN 61347-2-13 : 2014 AMD 1 2017 | Identical |
| UNE-EN 61347-2-13:2015 | Identical |
| IEC 60950-1:2005+AMD1:2009+AMD2:2013 CSV | Information technology equipment - Safety - Part 1: General requirements |
| IEC 61558-2-13:2009 | Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V - Part 2-13: Particular requirements and tests for auto transformers and power supply units incorporating auto transformers |
| IEC 61558-2-1:2007 | Safety of power transformers, power supplies, reactors and similar products - Part 2-1: Particular requirements and tests for separating transformers and power supplies incorporating separating transformers for general applications |
| IEC 61547:2009 | Equipment for general lighting purposes - EMC immunity requirements |
| EN 61558-2-16:2009/A1:2013 | SAFETY OF TRANSFORMERS, REACTORS, POWER SUPPLY UNITS AND SIMILAR PRODUCTS FOR SUPPLY VOLTAGES UP TO 1 100 V - PART 2-16: PARTICULAR REQUIREMENTS AND TESTS FOR SWITCH MODE POWER SUPPLY UNITS AND TRANSFORMERS FOR SWITCH MODE POWER SUPPLY UNITS (IEC 61558-2-16:2009/A1:2013) |
| IEC 60384-14:2013+AMD1:2016 CSV | Fixed capacitors for use in electronic equipment - Part 14: Sectional specification - Fixed capacitors for electromagnetic interference suppression and connection to the supply mains |
| IEC 60364-4-41:2005+AMD1:2017 CSV | Low voltage electrical installations - Part 4-41: Protection for safety - Protection against electric shock |
| IEC 61558-2-4:2009 | Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V - Part 2-4: Particular requirements and tests for isolating transformers and power supply units incorporating isolating transformers |
| IEC 61558-2-16:2009+AMD1:2013 CSV | Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V - Part 2-16: Particularrequirements and tests for switch mode power supply units andtransformers for switch mode power supply units |
| EN 62384:2006/A1:2009 | DC OR AC SUPPLIED ELECTRONIC CONTROL GEAR FOR LED MODULES - PERFORMANCE REQUIREMENTS |
| IEC 61347-1:2015 RLV | Lamp controlgear - Part 1: General and safety requirements |
| IEC 61558-2-6:2009 | Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V - Part 2-6: Particular requirements and tests for safety isolating transformers and power supply units incorporating safety isolating transformers |
| IEC 62384:2006+AMD1:2009 CSV | DC or AC supplied electronic control gear for LED modules - Performance requirements |
| IEC 60085:2007 | Electrical insulation - Thermal evaluation and designation |
| IEC 61558-1:2017 | Safety of transformers, reactors, power supply units and combinations thereof - Part 1: General requirements and tests |
| EN 61347-2-7:2012 | Lamp controlgear - Part 2-7: Particular requirements for battery supplied electronic controlgear for emergency lighting (self-contained) |
| EN 61347-1:2015 | Lamp controlgear - Part 1: General and safety requirements |
| IEC 61347-2-7:2011+AMD1:2017 CSV | Lamp controlgear - Part 2-7: Particular requirements for battery supplied electronic controlgear for emergency lighting (self-contained) |
| IEC 62504:2014 | General lighting - Light emitting diode (LED) products and related equipment - Terms and definitions |
| EN 61558-2-6:2009 | Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V - Part 2-6: Particular requirements and tests for safety isolating transformers and power supply units incorporating safety isolating transformers |
| EN 61547:2009 | Equipment for general lighting purposes - EMC immunity requirements |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.