I.S. EN 61029-1:2009
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
SAFETY OF TRANSPORTABLE MOTOR-OPERATED ELECTRIC TOOLS - PART 1: GENERAL REQUIREMENTS
Hardcopy , PDF
09-08-2015
English
01-15-2010
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Definitions
3 General requirement
4 General notes on tests
5 Rating
6 Classification
7 Marking and information for use
8 Protection against electric shock
9 Starting
10 Input and current
11 Heating
12 Leakage current
13 Environmental requirements
14 Protection against ingress of foreign bodies
and moisture resistance
15 Insulation resistance and electric strength
16 Endurance
17 Abnormal operation
18 Stability and mechanical hazards
19 Mechanical strength
20 Construction
21 Internal wiring
22 Components
23 Supply connection and external flexible cables and cords
24 Terminals for external conductors
25 Provision for earthing
26 Screws and connections
27 Creepage distances, clearances and distances through
insulation
28 Resistance to heat, fire and tracking
29 Resistance to rusting
30 Radiation
Annex A (normative) - Normative references
Annex B (normative) - Thermal cut-outs and overload releases
Annex C (normative) - Electronic circuits
Annex D (normative) - Measurement of creepage distances and
clearances
Annex IA (informative) - Circuit for measuring leakage currents
Annex ZA (informative) - Rules for routine tests
Annex ZB (normative) - Special national conditions
Annex ZC (informative) - Possible sources of errors during
vibration measurements
Annex ZD (informative) - Dust measurement
Pertains to electric motor-operated or magnetically-driven tools, intended for both indoor and outdoor use.
| DevelopmentNote |
For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017) 2009 Edition is Partially Superseded by I.S. EN 62841-1. (07/2017)
|
| DocumentType |
Standard
|
| Pages |
89
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| DIN EN 61029-1 : 2010 AMD 11 2011 | Identical |
| IEC 61029-1:1990 | Identical |
| NBN EN 61029-1 : 2009 AMD 1 2011 | Identical |
| NF EN 61029-1 : 2009 AMD 11 2011 | Identical |
| BS EN 61029-1 : 2009 | Identical |
| SN EN 61029-1 : 2009 AMD 11 2010 | Identical |
| EN 61029-1:2009/A11:2010 | Identical |
| UNE-EN 61029-1:2010 | Identical |
| EN 12096:1997 | Mechanical vibration - Declaration and verification of vibration emission values |
| IEC 60320-1:2015 | Appliance couplers for household and similar general purposes - Part 1: General requirements |
| EN 294:1992/AC:1993 | SAFETY OF MACHINERY - SAFETY DISTANCES TO PREVENT DANGER ZONES BEING REACHED BY THE UPPER LIMBS |
| EN 60745-1:2009/A11:2010 | HAND-HELD MOTOR-OPERATED ELECTRIC TOOLS - SAFETY - PART 1: GENERAL REQUIREMENTS |
| EN 60068-2-75:2014 | Environmental testing - Part 2-75: Tests - Test Eh: Hammer tests |
| IEC 61540:1997+AMD1:1998 CSV | Electrical accessories - Portable residual current devices without integral overcurrent protection for household and similar use (PRCDs) |
| IEC 60127-3:2015 | Miniature fuses - Part 3: Sub-miniature fuse-links |
| ISO 3744:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for an essentially free field over a reflecting plane |
| IEC 60384-14:2013+AMD1:2016 CSV | Fixed capacitors for use in electronic equipment - Part 14: Sectional specification - Fixed capacitors for electromagnetic interference suppression and connection to the supply mains |
| EN 1088:1995+A2:2008 | Safety of machinery - Interlocking devices associated with guards - Principles for design and selection |
| EN 60065:2014/AC:2017-01 | AUDIO, VIDEO AND SIMILAR ELECTRONIC APPARATUS - SAFETY REQUIREMENTS (IEC 60065:2014/COR2:2016) |
| ISO 820:1975 | Particle boards Definition and classification |
| IEC TR 60083:2015 | Plugs and socket-outlets for domestic and similar general use standardized in member countries of IEC |
| EN 349:1993+A1:2008 | Safety of machinery - Minimum gaps to avoid crushing of parts of the human body |
| EN 1093-3:2006+A1:2008 | Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 3: Test bench method for the measurement of the emission rate of a given pollutant |
| EN 60127-3:2015 | Miniature fuses - Part 3: Sub-miniature fuse-links |
| EN 50144-1 : 98 COR 2005 | SAFETY OF HAND-HELD ELECTRIC MOTOR OPERATED TOOLS - PART 1: GENERAL REQUIREMENTS |
| CR 1030-1:1995 | Hand-arm vibration - Guidelines for vibration hazards reduction - Part 1: Engineering methods by design of machinery |
| IEC 60085:2007 | Electrical insulation - Thermal evaluation and designation |
| EN ISO 11201:2010 | Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections (ISO 11201:2010) |
| ISO 16063-1:1998 | Methods for the calibration of vibration and shock transducers Part 1: Basic concepts |
| HD 566 : 200S1 | THERMAL EVALUATION AND CLASSIFICATION OF ELECTRICAL INSULATION |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| EN ISO 3744:2010 | Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for an essentially free field over a reflecting plane (ISO 3744:2010) |
| IEC 61058-1:2016 | Switches for appliances - Part 1: General requirements |
| EN 953:1997+A1:2009 | Safety of machinery - Guards - General requirements for the design and construction of fixed and movable guards |
| ISO 8041:2005 | Human response to vibration Measuring instrumentation |
| IEC 60745-1:2006 | Hand-held motor-operated electric tools - Safety - Part 1: General requirements |
| IEC 60068-2-75:2014 | Environmental testing - Part 2-75: Tests - Test Eh: Hammer tests |
| EN 61058-1:2002/A2:2008 | SWITCHES FOR APPLIANCES - PART 1: GENERAL REQUIREMENTS |
| ISO 630:1995 | Structural steels Plates, wide flats, bars, sections and profiles |
| EN ISO 4871:2009 | Acoustics - Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996) |
| EN 60335-1:2012/A13:2017 | HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60335-1:2010, MODIFIED) |
| EN 60799:1998 | Electrical accessories - Cord sets and interconnection cord sets |
| EN 60651:1994/A2:2001 | SOUND LEVEL METERS (IEC 60651:1979/A2:2000) |
| EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
| IEC 60309-1:1999+AMD1:2005+AMD2:2012 CSV | Plugs, socket-outlets and couplers for industrial purposes - Part 1: General requirements |
| EN 60309-2:1999/A2:2012 | PLUGS, SOCKET-OUTLETS AND COUPLERS FOR INDUSTRIAL PURPOSES - PART 2: DIMENSIONAL INTERCHANGEABILITY REQUIREMENTS FOR PIN AND CONTACT-TUBE ACCESSORIES (IEC 60309-2:1999/A2:2012) |
| IEC 60309-2:1999+AMD1:2005+AMD2:2012 CSV | Plugs, socket-outlets and couplers for industrial purposes - Part 2: Dimensional interchangeability requirements for pin and contact-tube accessories |
| IEC 60651:1979+AMD1:1993+AMD2:2000 CSV | Sound level meters |
| EN 60320-1:2015/AC:2016 | APPLIANCE COUPLERS FOR HOUSEHOLD AND SIMILAR GENERAL PURPOSES - PART 1: GENERAL REQUIREMENTS (IEC 60320-1:2015/COR1:2016) |
| EN 60309-1:1999/A1:2007/AC:2014 | PLUGS, SOCKET-OUTLETS AND COUPLERS FOR INDUSTRIAL PURPOSES - PART 1: GENERAL REQUIREMENTS (IEC 60309-1:1999/A2:2012) |
| IEC 60799:1998 | Electrical accessories - Cord sets and interconnection cord sets |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.