I.S. EN 61020-1:2009
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
ELECTROMECHANICAL SWITCHES FOR USE IN ELECTRICAL AND ELECTRONIC EQUIPMENT - PART 1: GENERIC SPECIFICATION
Available format(s)
Hardcopy , PDF
Superseded date
02-20-2022
Superseded by
Language(s)
English
Published date
01-01-2009
Publisher
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
FOREWORD
INTRODUCTION
1 Scope and object
2 General
3 Quality assessment procedures
4 Test and measurement procedures
Annex A (informative) - Quality assurance procedures
Bibliography
Annex ZA (normative) - Normative references to
international publications with their
corresponding European publications
Applies to electromechanical switches intended for use in electrical and electronic appliances.
| DevelopmentNote |
Supersedes I.S. EN 196000, I.S. EN 196103 and I.S. EN 196500. (10/2009) For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
|
| DocumentType |
Standard
|
| Pages |
73
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| EN 61020-1:2009 | Identical |
| IEC 61020-1:2009 | Identical |
| IEC 60068-2-43:2003 | Environmental testing - Part 2-43: Tests - Test Kd: Hydrogen sulphide test for contacts and connections |
| ISO/IEC 17050-1:2004 | Conformity assessment Supplier's declaration of conformity Part 1: General requirements |
| IEC 60068-2-68:1994 | Environmental testing - Part 2-68: Tests - Test L: Dust and sand |
| IEC 60068-1:2013 | Environmental testing - Part 1: General and guidance |
| EN 60068-2-42:2003 | Environmental testing - Part 2-42: Tests - Test Kc: Sulphur dioxide test for contacts and connections |
| IEC 60068-2-58:2015+AMD1:2017 CSV | Environmental testing - Part 2-58: Tests - Test Td: Test methods for solderability, resistance to dissolution of metallization and to soldering heat of surface mounting devices (SMD) |
| IEC 60068-2-27:2008 | Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock |
| IEC 60068-2-20:2008 | Environmental testing - Part 2-20: Tests - Test T: Test methods for solderability and resistance to soldering heat of devices with leads |
| EN 60068-2-20:2008 | Environmental testing - Part 2-20: Tests - Test T: Test methods for solderability and resistance to soldering heat of devices with leads |
| EN 60068-2-1:2007 | Environmental testing - Part 2-1: Tests - Test A: Cold |
| IEC 60068-2-49:1983 | Basic environmental testing procedures - Part 2-49: Tests - Guidance to test Kc: Sulphur dioxide test for contacts and connections |
| EN 60068-2-2:2007 | Environmental testing - Part 2-2: Tests - Test B: Dry heat |
| ISO 1101:2017 | Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out |
| IEC 60068-2-21:2006 | Environmental testing - Part 2-21: Tests - Test U: Robustness of terminations and integral mounting devices |
| IEC 60068-2-13:1983 | Basic environmental testing procedures - Part 2-13: Tests - Test M: Low air pressure |
| EN 60068-1:2014 | Environmental testing - Part 1: General and guidance |
| ISO/IEC Guide 60:2004 | Conformity assessment Code of good practice |
| IECQ 01:2014 | IEC QUALITY ASSESSMENT SYSTEM FOR ELECTRONIC COMPONENTS (IECQ SYSTEM) - BASIC RULES |
| IEC 60068-2-38:2009 | Environmental testing - Part 2-38: Tests - Test Z/AD: Composite temperature/humidity cyclic test |
| IEC 60410:1973 | Sampling plans and procedures for inspection by attributes |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| IEC 60068-2-77:1999 | Environmental testing - Part 2-77: Tests - Test 77: Body strength and impact shock |
| EN 60068-2-17:1994 | Environmental testing - Part 2: Tests - Test Q: Sealing |
| IEC 61058-1:2016 | Switches for appliances - Part 1: General requirements |
| IEC 60068-2-17:1994 | Basic environmental testing procedures - Part 2-17: Tests - Test Q: Sealing |
| ISO 286-1:2010 | Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 1: Basis of tolerances, deviations and fits |
| IEC 60068-2-10:2005 | Environmental testing - Part 2-10: Tests - Test J and guidance: Mould growth |
| ISO/IEC 17050-2:2004 | Conformity assessment Supplier's declaration of conformity Part 2: Supporting documentation |
| EN 60068-2-21:2006 | Environmental testing - Part 2-21: Tests - Test U: Robustness of terminations and integral mounting devices |
| IEC 60068-2-2:2007 | Environmental testing - Part 2-2: Tests - Test B: Dry heat |
| IEC 60695-11-10:2013 | Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods |
| EN 60068-2-68:1996 | Environmental testing - Part 2: Tests - Test L: Dust and sand |
| IEC 60062:2016 | Marking codes for resistors and capacitors |
| IEC 60068-2-61:1991 | Environmental testing - Part 2-61: Test methods - Test Z/ABDM:Climatic sequence |
| ISO 9001:2015 | Quality management systems — Requirements |
| IEC 60068-2-42:2003 | Environmental testing - Part 2-42: Tests - Test Kc: Sulphur dioxide test for contacts and connections |
| ISO 129-1:2004 | Technical drawings Indication of dimensions and tolerances Part 1: General principles |
| EN 60068-2-78:2013 | Environmental testing - Part 2-78: Tests - Test Cab: Damp heat, steady state |
| EN 60068-2-13:1999 | Environmental testing - Part 2: Tests - Test M: Low air pressure |
| IEC 60721-3-3:1994+AMD1:1995+AMD2:1996 CSV | Classification of environmental conditions - Part 3-3: Classification of groups of environmental parameters and their severities - Stationary use at weatherprotected locations |
| EN 60068-2-6:2008 | Environmental testing - Part 2-6: Tests - Test Fc: Vibration (sinusoidal) |
| EN 60068-2-61:1993 | Environmental testing - Part 2: Test methods - Test Z/ABDM: Climatic sequence |
| EN 61058-1:2002/A2:2008 | SWITCHES FOR APPLIANCES - PART 1: GENERAL REQUIREMENTS |
| EN 60068-2-43:2003 | Environmental testing - Part 2-43: Tests - Test Kd: Hydrogen sulphide test for contacts and connections |
| IEC 60068-2-1:2007 | Environmental testing - Part 2-1: Tests - Test A: Cold |
| EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
| EN 60068-2-30:2005 | Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle) |
| IEC 60068-2-44:1995 | Environmental testing - Part 2-44: Tests - Guidance on test T: Soldering |
| IEC TS 60695-11-4:2004 | Fire hazard testing - Part 11-4: Test flames - 50 W flame - Apparatus and confirmational test method |
| IEC 60068-2-14:2009 | Environmental testing - Part 2-14: Tests - Test N: Change of temperature |
| EN 60068-2-45:1992/A1:1993 | Environmental testing - Part 2: Tests - Test Xa and guidance: Immersion in cleaning solvents |
| IEC 60664-1:2007 | Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests |
| EN 60068-2-14:2009 | Environmental testing - Part 2-14: Tests - Test N: Change of temperature |
| IEC 60050-581:2008 | International Electrotechnical Vocabulary (IEV) - Part 581: Electromechanical components for electronic equipment |
| IEC 61190-1-3:2007+AMD1:2010 CSV | Attachment materials for electronic assembly - Part 1-3: Requirements for electronic grade solder alloys and fluxed and non-fluxed solid solders for electronic soldering applications |
| IEC 60068-2-46:1982 | Basic environmental testing procedures - Part 2-46: Tests - Guidance to test Kd: Hydrogen sulphide test for contacts and connections |
| IEC 60068-2-30:2005 | Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.