I.S. EN 60317-0-6:2001
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 0-6: GENERAL REQUIREMENTS - GLASS-FIBRE WOUND RESIN OR VARNISH IMPREGNATED, BARE OR ENAMELLED ROUND COPPER WIRE
Hardcopy , PDF
09-14-2020
English
01-01-2001
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Definitions, general notes on methods of test and appearance
3.1 Definitions
3.2 General notes on methods of test
4 Dimensions
4.1 Conductor diameter
4.2 Out of roundness of conductor
4.3 Minimum increase in diameter due to the covering
4.4 Maximum overall diameter
5 Electrical resistance
6 Elongation
7 Springiness
7.1 Nominal conductor diameters up to and including 1,600 mm
7.2 Nominal conductor diameters over 1,600 mm
8 Flexibility and adherence
9 Heat shock
10 Cut-through
11 Resistance to abrasion
12 Resistance to solvent
13 Breakdown voltage
13.1 Glass-fibre covered round copper wires
13.2 Glass-fibre covered enamelled round copper wires
14 Continuity of covering
15 Temperature index
16 Resistance to refrigerants
17 Solderability
18 Heat or solvent bonding
19 Dielectric dissipation factor
20 Resistance to hydrolysis and to transformer oil
21 Loss of mass
22 Packaging
Annex A (informative) Diameters for intermediate nominal
conductor diameters
Annex B (informative) Resistance
Annex C (informative) High temperature failure test
Annex ZA (normative) Normative references to international
publications with their corresponding European
publications
Bibliography
Defines general requirements of glass-fibre wound resin or varnish impregnated, bare or enamelled, round copper winding wires.
| DevelopmentNote |
For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
|
| DocumentType |
Standard
|
| Pages |
58
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| BS EN 60317-0-6:2001 | Identical |
| IEC 60317-0-6:2001+AMD1:2006 CSV | Identical |
| NF EN 60317-0-6 : 2002 AMD 1 2007 | Identical |
| DIN EN 60317-0-6:2007-10 | Identical |
| SN EN 60317-0-6 : 2001 | Identical |
| EN 60317-0-6:2001/A1:2006 | Identical |
| UNE-EN 60317-0-6:2002 | Identical |
| ISO 3:1973 | Preferred numbers Series of preferred numbers |
| IEC 60851-6:2012 | Winding wires - Test methods - Part 6: Thermal properties |
| IEC 60851-5:2008+AMD1:2011 CSV | Winding wires - Test methods - Part 5: Electrical properties |
| EN 60851-6:2012 | Winding wires - Test methods - Part 6: Thermal properties |
| EN 60851-5:2008/A1:2011 | WINDING WIRES - TEST METHODS - PART 5: ELECTRICAL PROPERTIES (IEC 60851-5:2008) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.