I.S. EN 60317-0-3:2008
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 0-3: GENERAL REQUIREMENTS - ENAMELLED ROUND ALUMINIUM WIRE
Hardcopy , PDF
11-14-2019
English
01-01-2008
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms, definitions, general notes and appearance
4 Dimensions
5 Electrical resistance
6 Elongation
7 Springiness
8 Flexibility and adherence
9 Heat shock
10 Cut-through
11 Resistance to abrasion
12 Resistance to solvents
13 Breakdown voltage
14 Continuity of insulation (nominal conductor diameters
up to and including 1,600 mm)
15 Temperature index
16 Resistance to refrigerants
17 Solderability
18 Heat or solvent bonding
19 Dielectric dissipation factor
20 Resistance to transformer oil
21 Loss of mass
23 Pin hole test
30 Packaging
Annex A (informative) - Dimensions for intermediate nominal
conductor diameters (R 40)
Annex B (informative) - Method for the calculation of linear
resistance
Annex C (informative) - Resistance
Annex ZA (normative) - Normative references to international
Publications with their corresponding European
publications
Bibliography
Describes the general requirements of enamelled round aluminium winding wires with or without a bonding layer.
| DevelopmentNote |
2008 Edition Re-Issued in December 2013 & incorporates AMD 1 2013. (01/2014) For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
|
| DocumentType |
Standard
|
| Pages |
74
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| EN 60317-0-3:2008/A1:2013 | Identical |
| DIN EN 60317-0-3:2014-09 | Identical |
| SN EN 60317-0-3 : 1998 AMD 1 2000 | Identical |
| BS EN 60317-0-3 : 2008 | Identical |
| IEC 60317-0-3:2008+AMD1:2013 CSV | Identical |
| UNE-EN 60317-0-3:2008 | Identical |
| ISO 3:1973 | Preferred numbers Series of preferred numbers |
| EN 60317-25:2010 | Specifications for particular types of winding wires - Part 25: Polyester or polyesterimide overcoated with polyamide-imide enamelled round aluminium wire, class 200 |
| IEC 60172:2015 | Test procedure for the determination of the temperature index of enamelled and tape wrapped winding wires |
| EN 60172:2015 | Test procedure for the determination of the temperature index of enamelled and tape wrapped winding wires |
| IEC 60317-25:2010 | Specifications for particular types of winding wires - Part 25: Polyester or polyesterimide overcoated with polyamide-imide enamelled round aluminium wire, class 200 |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.