I.S. EN 60214-1:2014
Current
The latest, up-to-date edition.
TAP-CHANGERS - PART 1: PERFORMANCE REQUIREMENTS AND TEST METHODS
Hardcopy , PDF
English
01-01-2014
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
FOREWORD
1 Scope
2 Normative references
3 Terms and definitions
4 Service conditions
5 Requirements for on-load tap-changers
6 Requirements for motor-drive mechanisms for
on-load tap-changers
7 Requirements for de-energized tap-changers
8 Requirements for motor-drive mechanisms for
de-energized tap-changers
9 Nameplate
10 De-energized tap-changer warning label
11 Manufacturers operating instructions
Annex A (normative) - Supplementary information on
switching duty on main and transition contacts
relating to resistor type tap-changers
Annex B (normative) - Supplementary information on
switching duty relating to reactor type
tap-changers
Annex C (normative) - Method for determining the
equivalent temperature of the transition
resistor using power pulse current
Annex D (informative) - Simulated a.c. circuits for
service duty and breaking capacity tests
Annex E (informative) - Example of a synthetic
test circuit for service duty test of
vacuum type tap-changers
Bibliography
Annex ZA (normative) - Normative references to
international publications with their
corresponding European publications
Pertains to on-load tap-changers of both resistor and reactor types, deenergized tap-changers, and their motor-drive mechanisms.
| DevelopmentNote |
Supersedes I.S. EN 60214. (03/2006) For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
|
| DocumentType |
Standard
|
| Pages |
88
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| BS EN 60214-1:2014 | Identical |
| EN 60214-1:2014 | Identical |
| UNE-EN 60214-1:2015 | Identical |
| NF EN 60214-1 : 2015 | Identical |
| NBN EN 60214-1 : 2014 | Identical |
| DIN EN 60214-1 : 2015 | Identical |
| IEC 60214-1:2014 | Identical |
| IEC 60076-15:2015 | Power transformers - Part 15: Gas-filled power transformers |
| IEC 60270:2000+AMD1:2015 CSV | High-voltage test techniques - Partial discharge measurements |
| IEC 60076-7:2005 | Power transformers - Part 7: Loading guide for oil-immersed power transformers |
| EN 60060-1:2010 | High-voltage test techniques - Part 1: General definitions and test requirements |
| IEC 60599:2015 | Mineral oil-filled electrical equipment in service - Guidance on the interpretation of dissolved and free gases analysis |
| IEC 60376:2005 | Specification of technical grade sulfur hexafluoride (SF<sub>6</sub>) for use in electrical equipment |
| EN 60270:2001/A1:2016 | HIGH-VOLTAGE TEST TECHNIQUES - PARTIAL DISCHARGE MEASUREMENTS (IEC 60270:2000/A1:2015) |
| IEC 60076-12:2008 | Power transformers - Part 12: Loading guide for dry-type power transformers |
| IEC 60296:2012 RLV | Fluids for electrotechnical applications - Unused mineral insulating oils for transformers and switchgear |
| IEC 60076-3:2013 | Power transformers - Part 3: Insulation levels, dielectric tests and external clearances in air |
| IEC 60050-421:1990 | International Electrotechnical Vocabulary (IEV) - Part 421: Power transformers and reactors |
| EN 60296:2012 | Fluids for electrotechnical applications - Unused mineral insulating oils for transformers and switchgear |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| IEC 60137:2017 | Insulated bushings for alternating voltages above 1000 V |
| IEC 60076-1:2011 | Power transformers - Part 1: General |
| IEC 60076-21:2011 | Power transformers - Part 21: Standard requirements, terminology, and test code for step-voltage regulators |
| IEC 60060-1:2010 | High-voltage test techniques - Part 1: General definitions and test requirements |
| IEC 60214-2:2004 | Tap-changers - Part 2: Application guide |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.