I.S. EN 50700:2014
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
INFORMATION TECHNOLOGY - PREMISES DISTRIBUTION ACCESS NETWORK (PDAN) CABLING TO SUPPORT DEPLOYMENT OF OPTICAL BROADBAND NETWORKS
Hardcopy , PDF
10-22-2023
English
01-01-2014
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms, definitions and abbreviations
4 Conformance
5 Structure of PDAN cabling within multi-subscriber
premises
6 PDAN cabling performance
7 Implementation options
8 Cable requirements
9 Connecting hardware requirements
10 Cords
11 Accommodation of the Subscriber Interface (SI) and
the Customer Premises Equipment (CPE)
Annex A (informative) - Broadband infrastructure external to
multi-subscriber premises
Bibliography
Describes the optical fibre optical fibre access network cabling within multisubscriber premises termed the premises distribution access network (PDAN).
| DocumentType |
Standard
|
| Pages |
32
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| EN 50700:2014 | Identical |
| TR 105 174-2-1 : 1.1.1 | ACCESS, TERMINALS, TRANSMISSION AND MULTIPLEXING (ATTM); BROADBAND DEPLOYMENT - ENERGY EFFICIENCY AND KEY PERFORMANCE INDICATORS; PART 2: NETWORK SITES; SUB-PART 1: OPERATOR SITES |
| IEC 60825-2:2004+AMD1:2006+AMD2:2010 CSV | Safety of laser products - Part 2: Safety of optical fibre communication systems (OFCS) |
| EN 50377-7-4:2011 | Connector sets and interconnect components to be used in optical fibre communication systems - Product specifications - Part 7-4: LC-PC simplex terminated on IEC 60793-2-50 category B1.1 and B1.3 singlemode fibre with full zirconia ferrule for category C |
| EN 50346 : 2002 AMD 2 2009 | INFORMATION TECHNOLOGY - CABLING INSTALLATION - TESTING OF INSTALLED CABLING |
| EN 50174-1:2009/A2:2014 | INFORMATION TECHNOLOGY - CABLING INSTALLATION - PART 1: INSTALLATION SPECIFICATION AND QUALITY ASSURANCE |
| PREN 50411-3-8 : DRAFT 2014 | FIBRE ORGANIZERS AND CLOSURES TO BE USED IN OPTICAL FIBRE COMMUNICATION SYSTEMS - PRODUCT SPECIFICATIONS - PART 3-8: FIBRE MANAGEMENT SYSTEM, TERMINAL EQUIPMENT BOX TYPE 1 FOR CATEGORY C |
| EN 60793-2-50:2016 | Optical fibres - Part 2-50: Product specifications - Sectional specification for class B single-mode fibres |
| CLC/TR 50510:2012 | Fibre optic access to end-user - A guideline to building of FTTX fibre optic network |
| EN 50411-3-2:2011 | Fibre organisers and closures to be used in optical fibre communication systems - Product specifications - Part 3-2: Singlemode mechanical fibre splice |
| TS 105 174-1 : 1.2.1 | ACCESS, TERMINALS, TRANSMISSION AND MULTIPLEXING (ATTM); BROADBAND DEPLOYMENT AND ENERGY MANAGEMENT; PART 1: OVERVIEW, COMMON AND GENERIC ASPECTS |
| EN 60794-5-10:2014 | Optical fibre cables - Part 5–10: Family specification - Outdoor microduct optical fibre cables, microducts and protected microducts for installation by blowing |
| EN 61755-2-2 : 2006 | FIBRE OPTIC CONNECTOR OPTICAL INTERFACES - PART 2-2: OPTICAL INTERFACE STANDARD SINGLE MODE ANGLED PHYSICALLY CONTACTING FIBRES |
| CLC/TR 50173-99-3:2012 | Information technology - Generic cabling systems - Part 99-3: Home cabling infrastructures up to 50 m in length to support simultaneous and non simultaneous provision of applications |
| EN 50173-3 : 2007 COR 2011 | INFORMATION TECHNOLOGY - GENERIC CABLING SYSTEMS - PART 3: INDUSTRIAL PREMISES |
| EN 50174-3:2013/A1:2017 | INFORMATION TECHNOLOGY - CABLING INSTALLATION - PART 3: INSTALLATION PLANNING AND PRACTICES OUTSIDE BUILDINGS |
| EN 61280-4-2:2014 | Fibre-optic communication subsystem test procedures - Part 4-2: Installed cable plant - Single-mode attenuation and optical return loss measurement |
| EN 50173-1:2011 | Information technology - Generic cabling systems - Part 1: General requirements |
| EN 50174-2 : 2009 AMD 2 2014 | INFORMATION TECHNOLOGY - CABLING INSTALLATION - PART 2: INSTALLATION PLANNING AND PRACTICES INSIDE BUILDINGS |
| IEC 61280-4-2:2014 | Fibre-optic communication subsystem test procedures - Part 4-2: Installed cable plant - Single-mode attenuation and optical return loss measurement |
| IEC 61753-041-2:2014 | Fibre optic interconnecting devices and passive components - Performance standard - Part 041-2: Non-connectorized single-mode OTDR reflecting device for category C - Controlled environment |
| IEC 60794-5-10:2014 | Optical fibre cables - Part 5-10: Family specification - Outdoor microduct optical fibre cables, microducts and protected microducts for installation by blowing |
| EN 61755-1:2006/corrigendum:2006 | FIBRE OPTIC CONNECTOR OPTICAL INTERFACES - PART 1: OPTICAL INTERFACES FOR SINGLE MODE NON-DISPERSION SHIFTED FIBRES - GENERAL AND GUIDANCE |
| EN 60794-5-20:2014 | Optical fibre cables - Part 5-20: Family specification - Outdoor microduct fibre units, microducts and protected microducts for installation by blowing |
| IEC 60793-2-50:2015 | Optical fibres - Part 2-50: Product specifications - Sectional specification for class B single-mode fibres |
| IEC 60794-5-20:2014 | Optical fibre cables - Part 5-20: Family specification - Outdoor microduct fibre units, microducts and protected microducts for installation by blowing |
| IEC 61755-2-2:2006 | Fibre optic connector optical interfaces - Part 2-2: Optical interface standard single mode angled physically contacting fibres |
| EN 50411-6-1:2011 | Fibre organisers and closures to be used in optical fibre communication systems - Product specifications - Part 6-1: Unprotected microduct for category S and A |
| TS 102 873 : 1.1.1 | ACCESS, TERMINALS, TRANSMISSION AND MULTIPLEXING (ATTM); OPTICAL EXTERNAL NETWORK TESTING INTERFACE |
| IEC 61754-20:2012 | Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces - Part 20: Type LC connector family |
| EN 60825-2:2004/A2:2010 | SAFETY OF LASER PRODUCTS - PART 2: SAFETY OF OPTICAL FIBRE COMMUNICATION SYSTEMS (OFCS) |
| ISO/IEC 14763-3:2014 | Information technology — Implementation and operation of customer premises cabling — Part 3: Testing of optical fibre cabling |
| CLC/TR 50173-99-2:2010 | Information technology - Implementation of BCT applications using cabling in accordance with EN 50173-4 |
| EN 50173-5 : 2007 AMD 2 2012 | INFORMATION TECHNOLOGY - GENERIC CABLING SYSTEMS - PART 5: DATA CENTRES |
| EN 50173-4 : 2007 AMD 2 2012 | INFORMATION TECHNOLOGY - GENERIC CABLING SYSTEMS - PART 4: HOMES |
| CLC/TR 50173-99-1:2007 | Cabling guidelines in support of 10 GBASE-T |
| EN 50173-6:2013 | Information technology - Generic cabling systems - Part 6: Distributed building services |
| IEC 61755-1:2005 | Fibre optic connector optical interfaces - Part 1: Optical interfaces for single mode non-dispersion shifted fibres - General and guidance |
| EN 61754-20:2012 | Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces - Part 20: Type LC connector family |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.