I.S. EN 1852-1:2018
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - POLYPROPYLENE (PP) - PART 1: SPECIFICATIONS FOR PIPES, FITTINGS AND THE SYSTEM
Hardcopy , PDF
05-29-2023
English
01-01-2018
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
National Foreword
European foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviations
5 Material
6 General characteristics
7 Geometrical characteristics
8 Mechanical characteristics
9 Physical characteristics
10 Performance requirements
11 Sealing rings
12 Marking
Annex A (normative) - Utilization of non-virgin
PP material
Annex B (informative) - General characteristics
of PP pipes and fittings
Annex C (informative) - Product standards of
components that can be connected to
components conforming to this standard
Bibliography
Describes the requirements for solid wall pipes, fittings and the system of polypropylene (PP) piping systems intended for use for: - non-pressure underground drainage and sewerage outside the building structure (application area code 'U'), and - non-pressure underground drainage and sewerage for both buried in ground within the building structure (application area code 'D') and outside the building structure.
| DocumentType |
Standard
|
| Pages |
46
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| EN 1852-1:2018 | Identical |
| ONORM EN 1852-1 : 2016 | Identical |
| BS EN 1852-1:2009 | Identical |
| DIN EN 1852-1:2016-05 (Draft) | Identical |
| SN EN 1852-1 : 2009 | Identical |
| NBN EN 1852-1 : 2009 | Identical |
| UNE-EN 1852-1:2009 | Identical |
| UNI EN 1852-1 : 2009 | Identical |
| EN 295-3:2012 | Vitrified clay pipe systems for drains and sewers - Part 3: Test methods |
| ISO 580:2005 | Plastics piping and ducting systems — Injection-moulded thermoplastics fittings — Methods for visually assessing the effects of heating |
| EN ISO 3126:2005 | Plastics piping systems - Plastics components - Determination of dimensions (ISO 3126:2005) |
| ISO/TR 10358:1993 | Plastics pipes and fittings Combined chemical-resistance classification table |
| ISO 3451-1:2008 | Plastics Determination of ash Part 1: General methods |
| ISO 13263:2010 | Thermoplastics piping systems for non-pressure underground drainage and sewerage Thermoplastics fittings Test method for impact strength |
| ISO 1167-2:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces |
| ISO 265-1:1988 | Pipes and fittings of plastics materials Fittings for domestic and industrial waste pipes Basic dimensions: Metric series Part 1: Unplasticized poly(vinyl chloride) (PVC-U) |
| ISO 1133-1:2011 | Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 1: Standard method |
| ISO 11173:1994 | Thermoplastics pipes — Determination of resistance to external blows — Staircase method |
| EN ISO 11173:2017 | Thermoplastics pipes - Determination of resistance to external blows - Staircase method (ISO 11173:1994) |
| ISO 3127:1994 | Thermoplastics pipes — Determination of resistance to external blows — Round-the-clock method |
| EN ISO 3451-1:2008 | Plastics - Determination of ash - Part 1: General methods (ISO 3451-1:2008) |
| EN ISO 1167-2:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 2: Preparation of pipe test pieces (ISO 1167-2:2006) |
| ISO/TR 7620:2005 | Rubber materials — Chemical resistance |
| EN ISO 1167-1:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 1: General method (ISO 1167-1:2006) |
| CEN/TS 15223:2017 | Plastics piping systems - Validated design parameters of buried thermoplastics piping systems |
| CEN/TR 1046:2013 | Thermoplastics piping and ducting systems - Systems outside building structures for the conveyance of water or sewage - Practices for underground installation |
| ISO 3126:2005 | Plastics piping systems Plastics components Determination of dimensions |
| ISO 11922-1:1997 | Thermoplastics pipes for the conveyance of fluids — Dimensions and tolerances — Part 1: Metric series |
| EN 476:2011 | General requirements for components used in drains and sewers |
| EN ISO 1133-1:2011 | Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics - Part 1: Standard method (ISO 1133-1:2011) |
| ISO 472:2013 | Plastics — Vocabulary |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| EN ISO 3127:2017 | Thermoplastics pipes - Determination of resistance to external blows - Round-the-clock method (ISO 3127:1994) |
| EN 14758-1:2012 | Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene with mineral modifiers (PP-MD) - Part 1: Specifications for pipes, fittings and the system |
| CEN ISO/TR 27165:2012 | Thermoplastics piping systems - Guidance for definitions of wall constructions for pipes (ISO/TR 27165:2012) |
| EN ISO 13967:2009 | Thermoplastics fittings - Determination of ring stiffness (ISO 13967:2009) |
| ISO 1183-2:2004 | Plastics Methods for determining the density of non-cellular plastics Part 2: Density gradient column method |
| EN ISO 9969:2016 | Thermoplastics pipes - Determination of ring stiffness (ISO 9969:2016) |
| EN ISO 580:2005 | Plastics piping and ducting systems - Injection-moulded thermoplastics fittings - Methods for visually assessing the effects of heating (ISO 580:2005) |
| EN ISO 13254:2017 | Thermoplastics piping systems for non-pressure applications - Test method for watertightness (ISO 13254:2010) |
| EN 1401-1:2009 | Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system |
| ISO 11357-6:2008 | Plastics Differential scanning calorimetry (DSC) Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT) |
| ISO 4065:1996 | Thermoplastics pipes Universal wall thickness table |
| EN ISO 2505:2005 | Thermoplastics pipes - Longitudinal reversion - Test method and parameters (ISO 2505:2005) |
| ISO 13257:2010 | Thermoplastics piping systems for non-pressure applications Test method for resistance to elevated temperature cycling |
| EN ISO 13257:2017 | Thermoplastics piping systems for non-pressure applications - Test method for resistance to elevated temperature cycling (ISO 13257:2010) |
| ISO 13254:2010 | Thermoplastics piping systems for non-pressure applications Test method for watertightness |
| ISO 13264:2010 | Thermoplastics piping systems for non-pressure underground drainage and sewerage Thermoplastics fittings Test method for mechanical strength or flexibility of fabricated fittings |
| ISO 1043-1:2011 | Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics |
| ISO 9969:2016 | Thermoplastics pipes Determination of ring stiffness |
| CEN/TS 1852-2:2015 | Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene (PP) - Part 2: Guidance for the assessment of conformity |
| EN ISO 472:2013 | Plastics - Vocabulary (ISO 472:2013) |
| EN 12099:1997 | Plastics piping systems - Polyethylene piping materials and components - Determination of volatile content |
| EN ISO 1183-2:2004 | Plastics - Methods for determining the density of non-cellular plastics - Part 2: Density gradient column method (ISO 1183-2:2004) |
| ISO 1167-1:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method |
| ISO 2505:2005 | Thermoplastics pipes — Longitudinal reversion — Test method and parameters |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.