I.S. EN 16753:2016
Current
The latest, up-to-date edition.
GAS CYLINDERS - PERIODIC INSPECTION AND TESTING, IN SITU (WITHOUT DISMANTLING) OF REFILLABLE SEAMLESS STEEL TUBES OF WATER CAPACITY BETWEEN 150 L AND 3000 L, USED FOR COMPRESSED GASES
Hardcopy , PDF
English
01-01-2016
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
National Foreword
European foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Operational principles
5 NDE personnel qualification
6 Marking
7 Certification/Report
8 Rendering tubes unserviceable
Annex A (normative) - Description, evaluation of
defects and conditions for rejection of refillable
seamless steel pressure vessels (tubes) at the
time of visual inspection
Annex B (informative) - Procedure for the examination of
refillable seamless steel pressure vessels (tubes)
using acoustic emission (AE) techniques
Annex C (informative) - Recommended time intervals for
certain commonly contained gases
Annex D (informative) - Pre-inspection site survey
checklist/questionnaire
Bibliography
Defines requirements for using a combination of appropriate in situ (without dismantling), non-destructive examination (NDE) techniques, for example visual examination, acoustic emission testing [AT] and ultrasonic testing [UT] when periodically inspecting and testing seamless steel pressure vessels (tubes) with a water capacity between 150 l and 3000 l, used for compressed and liquefied gases for a further period of service.
| DocumentType |
Standard
|
| Pages |
28
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Current
|
| Standards | Relationship |
| EN 16753:2016 | Identical |
| ISO 25760:2009 | Gas cylinders — Operational procedures for the safe removal of valves from gas cylinders |
| ISO 19078:2013 | Gas cylinders — Inspection of the cylinder installation, and requalification of high pressure cylinders for the on-board storage of natural gas as a fuel for automotive vehicles |
| EN ISO 11120:2015 | Gas cylinders - Refillable seamless steel tubes of water capacity between 150 l and 3000 l - Design, construction and testing (ISO 11120:2015) |
| ISO 9712:2012 | Non-destructive testing Qualification and certification of NDT personnel |
| EN ISO 25760:2015 | Gas cylinders - Operational procedures for the safe removal of valves from gas cylinders (ISO 25760:2009) |
| EN ISO 13769:2009 | Gas cylinders - Stamp marking (ISO 13769:2007) |
| ISO 5579:2013 | Non-destructive testing — Radiographic testing of metallic materials using film and X- or gamma rays — Basic rules |
| EN ISO 9712:2012 | Non-destructive testing - Qualification and certification of NDT personnel (ISO 9712:2012) |
| EN ISO 9934-1:2016 | Non-destructive testing - Magnetic particle testing - Part 1: General principles (ISO 9934-1:2016) |
| EN ISO 5579:2013 | Non-destructive testing - Radiographic testing of metallic materials using film and X- or gamma rays - Basic rules (ISO 5579:2013) |
| ISO 11120:2015 | Gas cylinders Refillable seamless steel tubes of water capacity between 150 l and 3000 l Design, construction and testing |
| EN ISO 9809-1:2010 | Gas cylinders - Refillable seamless steel gas cylinders - Design, construction and testing - Part 1: Quenched and tempered steel cylinders with tensile strength less than 1 100 MPa (ISO 9809-1:2010) |
| ISO 9934-1:2016 | Non-destructive testing — Magnetic particle testing — Part 1: General principles |
| ISO 10286:2007 | Gas cylinders Terminology |
| ISO 15549:2008 | Non-destructive testing Eddy current testing General principles |
| ISO 16148:2016 | Gas cylinders Refillable seamless steel gas cylinders and tubes Acoustic emission examination (AT) and follow-up ultrasonic examination (UT) for periodic inspection and testing |
| ISO 6406:2005 | Gas cylinders Seamless steel gas cylinders Periodic inspection and testing |
| EN ISO 10286:2015 | Gas cylinders - Terminology (ISO 10286:2015) |
| EN ISO 15549:2010 | Non-destructive testing - Eddy current testing - General principles (ISO 15549:2008) |
| ISO/TR 16115:2013 | Gas cylinders Classification of imperfections arising during the manufacture of seamless steel and aluminium alloy gas cylinders |
| ISO 9809-1:2010 | Gas cylinders Refillable seamless steel gas cylinders Design, construction and testing Part 1: Quenched and tempered steel cylinders with tensile strength less than 1 100 MPa |
| EN ISO 16148:2016 | Gas cylinders - Refillable seamless steel gas cylinders and tubes - Acoustic emission examination (AT) and follow-up ultrasonic examination (UT) for periodic inspection and testing (ISO 16148:2016) |
| ISO 13769:2007 | Gas cylinders Stamp marking |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.