I.S. EN 16282-3:2016
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
EQUIPMENT FOR COMMERCIAL KITCHENS - COMPONENTS FOR VENTILATION IN COMMERCIAL KITCHENS - PART 3: KITCHEN VENTILATION CEILINGS - DESIGN AND SAFETY REQUIREMENTS
Hardcopy , PDF
11-30-2021
English
01-01-2016
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
National Foreword
European foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Ceiling types and configurations
5 Construction and function
6 Technical safety requirements
7 Hygienic requirements
8 Instructions
9 Marking
Bibliography
Defines requirements for the design, construction and operation of kitchen ventilation ceilings, including technical safety, ergonomic and hygienic features.
| DocumentType |
Standard
|
| Pages |
24
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy |
| EN 294:1992/AC:1993 | SAFETY OF MACHINERY - SAFETY DISTANCES TO PREVENT DANGER ZONES BEING REACHED BY THE UPPER LIMBS |
| PREN 16282-2 : DRAFT 2014 | EQUIPMENT FOR COMMERCIAL KITCHENS - COMPONENTS FOR VENTILATION OF COMMERCIAL KITCHENS - PART 2: KITCHEN VENTILATION HOODS; DESIGN AND SAFETY REQUIREMENTS |
| EN ISO 7250-1:2017 | Basic human body measurements for technological design - Part 1: Body measurement definitions and landmarks (ISO 7250-1:2017) |
| EN 1825-2:2002 | Grease separators - Part 2: Selection of nominal size, installation, operation and maintenance |
| EN 894-3:2000+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 3: Control actuators |
| EN 12464-1:2011 | Light and lighting - Lighting of work places - Part 1: Indoor work places |
| ISO 4287:1997 | Geometrical Product Specifications (GPS) — Surface texture: Profile method — Terms, definitions and surface texture parameters |
| PREN 16282-5 : DRAFT 2014 | EQUIPMENT FOR COMMERCIAL KITCHENS - COMPONENTS FOR VENTILATION IN COMMERCIAL KITCHENS - PART 5: AIR DUCT; DESIGN AND DIMENSIONING |
| EN 547-2:1996+A1:2008 | Safety of machinery - Human body measurements - Part 2: Principles for determining the dimensions required for access openings |
| EN 50274 : 2002 COR 2009 | LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES - PROTECTION AGAINST ELECTRIC SHOCK - PROTECTION AGAINST UNINTENTIONAL DIRECT CONTACT WITH HAZARDOUS LIVE PARTS |
| PREN 16282-8 : DRAFT 2014 | EQUIPMENT FOR COMMERCIAL KITCHENS - COMPONENTS FOR VENTILATION - PART 8: INSTALLATIONS FOR TREATMENT OF COOKING FUMES; REQUIREMENTS AND TESTING |
| EN ISO 4288:1997 | Geometrical product specifications (GPS) - Surface texture: Profile method - Rules and procedures for the assessment of surface texture (ISO 4288:1996) |
| EN 547-1:1996+A1:2008 | Safety of machinery - Human body measurements - Part 1: Principles for determining the dimensions required for openings for whole body access into machinery |
| ISO 12100:2010 | Safety of machinery — General principles for design — Risk assessment and risk reduction |
| PREN 16282-7 : DRAFT 2014 | EQUIPMENT FOR COMMERCIAL KITCHENS - COMPONENTS FOR VENTILATION IN COMMERCIAL KITCHENS - PART 7: INSTALLATION AND USE OF FIXED FIRE SUPPRESSION SYSTEMS |
| PREN 16282-6 : DRAFT 2014 | EQUIPMENT FOR COMMERCIAL KITCHENS - COMPONENTS FOR VENTILATION OF COMMERCIAL KITCHENS - PART 6: AEROSOL SEPARATORS; DESIGN AND SAFETY REQUIREMENTS |
| EN ISO 13565-2:1997 | Geometrical product specifications (GPS) - Surface texture: Profile method; surfaces having stratified functional properties - Part 2: Height characterization using the linear material ratio curve (ISO 13565-2:1996) |
| PREN 16282-4 : DRAFT 2014 | EQUIPMENT FOR COMMERCIAL KITCHENS - COMPONENTS FOR VENTILATION IN COMMERCIAL KITCHENS - PART 4: AIR INLETS AND OUTLETS; DESIGN AND SAFETY REQUIREMENTS |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| ISO 7250-1:2017 | Basic human body measurements for technological design — Part 1: Body measurement definitions and landmarks |
| ISO 3274:1996 | Geometrical Product Specifications (GPS) — Surface texture: Profile method — Nominal characteristics of contact (stylus) instruments |
| EN 547-3:1996+A1:2008 | Safety of machinery - Human body measurements - Part 3: Anthropometric data |
| EN ISO 12100:2010 | Safety of machinery - General principles for design - Risk assessment and risk reduction (ISO 12100:2010) |
| EN ISO 13565-1:1997 | Geometrical product specifications (GPS) - Surface texture: Profile method; surfaces having stratified functional properties - Part 1: Filtering and general measurement conditions (ISO 13565-1:1996) |
| PREN 16282-1 : DRAFT 2014 | EQUIPMENT FOR COMMERCIAL KITCHENS - COMPONENTS FOR VENTILATION OF COMMERCIAL KITCHENS - PART 1: GENERAL REQUIREMENTS INCLUDING CALCULATION METHOD |
| EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
| EN 573-3:2013 | Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 3: Chemical composition and form of products |
| EN ISO 3274:1997 | Geometrical product specifications (GPS) - Surface texture: Profile method - Nominal characteristics of contact (stylus) instruments (ISO 3274:1996) |
| EN 10088-1:2014 | Stainless steels - Part 1: List of stainless steels |
| EN 60204-1 : 2006 COR 2010 | SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.