I.S. EN 16129:2013
Current
The latest, up-to-date edition.
PRESSURE REGULATORS, AUTOMATIC CHANGEOVER DEVICES, HAVING A MAXIMUM REGULATED PRESSURE OF 4 BAR, WITH A MAXIMUM CAPACITY OF 150 KG/H, ASSOCIATED SAFETY DEVICES AND ADAPTORS FOR BUTANE, PROPANE, AND THEIR MIXTURES
Hardcopy , PDF
English
01-01-2013
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Types of regulating devices
5 Constructional characteristics
6 Performance characteristics
7 Test methods
8 Marking, packaging, instructions
Annex A (normative) - Special requirements for
devices fitted with pressure or flow rate
operated safety functions
Annex B (normative) - Special requirements for
devices fitted with a thermal shut off system
Annex C (normative) - Special requirements for
devices under extreme temperature
conditions (temperatures below -20 degrees C)
Annex D (normative) - Regulating devices for gas
cylinders to supply appliances installed in
caravans, motor caravans or freshwater
boats
Annex E (normative) - Complementary test requirements
for non-metallic thermoplastic or thermal setting
materials used in the construction of devices
Annex F (normative) - Requirements for elastomeric
reinforced diaphragms
Annex G (normative) - Inlet connections
Annex H (normative) - Outlet connections
Annex I (informative) - Test method for resistance to
corrosion
Annex J (informative) - Method for measuring leaks
Annex K (normative) - Special requirements for low
pressure fixed regulators fitted with two or
three outlets for outdoor use
Annex L (normative) - Special requirements for regulators
fitted with an inlet valve
Annex M (normative) - Devices for gas cylinders to supply
appliances installed in seawater boats
Annex N (normative) - Alternative possible seal
Annex ZA (informative) - Relationship between this European
Standard and the Essential Requirements of EU
Directive 2009/142/EC (for pressure regulators only)
Bibliography
Specifies the constructional and operational characteristics, the safety requirements, test methods and the marking of regulators and automatic change-over devices having a maximum regulated pressure of 4 bar, with a maximum capacity of 150 kg/h, for use with butane, propane and their mixtures in the vapour phase.
| DevelopmentNote |
Supersedes I.S. EN 12864, I.S. EN 13785 & I.S. EN 13786. (07/2013)
|
| DocumentType |
Standard
|
| Pages |
141
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| EN 16129:2013 | Identical |
| EN 15202:2012 | LPG equipment and accessories - Essential operational dimensions for LPG cylinder valve outlet and associated equipment connections |
| ISO 7005-2:1988 | Metallic flanges — Part 2: Cast iron flanges |
| CGA V 1 : 2013 | STANDARD FOR COMPRESSED GAS CYLINDER VALVE OUTLET AND INLET CONNECTIONS |
| ISO 8434-1:2007 | Metallic tube connections for fluid power and general use Part 1: 24 degree cone connectors |
| EN 10226-2:2005 | Pipe threads where pressure tight joints are made on the threads - Part 2: Taper external threads and taper internal threads - Dimensions, tolerances and designation |
| EN ISO 4892-3:2016 | Plastics - Methods of exposure to laboratory light sources - Part 3: Fluorescent UV lamps (ISO 4892-3:2016) |
| ISO 75:1987 | Plastics and ebonite Determination of temperature of deflection under load |
| ISO 565:1990 | Test sieves — Metal wire cloth, perforated metal plate and electroformed sheet — Nominal sizes of openings |
| EN 751-2:1996 | Sealing materials for metallic threaded joints in contact with 1st, 2nd and 3rd family gases and hot water - Part 2: Non-hardening jointing compounds |
| EN 561:2002 | Gas welding equipment - Quick-action coupling with shut-off valves for welding, cutting and allied processes |
| EN ISO 9227:2017 | Corrosion tests in artificial atmospheres - Salt spray tests (ISO 9227:2017) |
| EN 13878:2003 | Leisure accommodation vehicles - Terms and definitions |
| EN ISO 3166-1:2014 | Codes for the representation of names of countries and their subdivisions - Part 1: Country codes (ISO 3166-1:2013) |
| EN 1774:1997 | Zinc and zinc alloys - Alloys for foundry purposes - Ingot and liquid |
| EN ISO 228-1:2003 | Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000) |
| ISO 4628-3:2016 | Paints and varnishes — Evaluation of degradation of coatings — Designation of quantity and size of defects, and of intensity of uniform changes in appearance — Part 3: Assessment of degree of rusting |
| EN ISO 4628-3:2016 | Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and size of defects, and of intensity of uniform changes in appearance - Part 3: Assessment of degree of rusting (ISO 4628-3:2016) |
| EN 437:2003+A1:2009 | Test gases - Test pressures - Appliance categories |
| ISO 180:2000 | Plastics Determination of Izod impact strength |
| ISO 4892-3:2016 | Plastics — Methods of exposure to laboratory light sources — Part 3: Fluorescent UV lamps |
| EN 521:2006 | Specifications for dedicated liquefied petroleum gas appliances - Portable vapour pressure liquefied petroleum gas appliances |
| IEC 60695-11-10:2013 | Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods |
| EN 751-1:1996 | Sealing materials for metallic threaded joints in contact with 1st, 2nd and 3rd family gases and hot water - Part 1: Anaerobic jointing compounds |
| EN 1563:2011 | Founding - Spheroidal graphite cast irons |
| EN 12164:2016 | Copper and copper alloys - Rod for free machining purposes |
| ISO 9227:2017 | Corrosion tests in artificial atmospheres — Salt spray tests |
| ISO 3166-1:2013 | Codes for the representation of names of countries and their subdivisions Part 1: Country codes |
| EN 12420:2014 | Copper and copper alloys - Forgings |
| ISO 7005-1:2011 | Pipe flanges — Part 1: Steel flanges for industrial and general service piping systems |
| EN 12844:1998 | Zinc and zinc alloys - Castings - Specifications |
| EN 549:1994 | Rubber materials for seals and diaphragms for gas appliances and gas equipment |
| EN 12165:2016 | Copper and copper alloys - Wrought and unwrought forging stock |
| EN 10226-1:2004 | Pipe threads where pressure tight joints are made on the threads - Part 1: Taper external threads and parallel internal threads - Dimensions, tolerances and designation |
| ISO 178:2010 | Plastics Determination of flexural properties |
| ISO 228-1:2000 | Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.