I.S. EN 15632-1:2009
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
DISTRICT HEATING PIPES - PRE-INSULATED FLEXIBLE PIPE SYSTEMS - PART 1: CLASSIFICATION, GENERAL REQUIREMENTS AND TEST METHODS
Hardcopy , PDF
06-07-2022
English
02-23-2009
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Classification
5 Requirements
6 Test methods
7 Marking
8 Manufacturer's information
Annex A (normative) - Thermal conductivity of
pre-insulated pipes - Test procedure
Annex B (normative) - Calculation of the heat flow from
the medium to the ambient loss of pre-insulated
buried district heating pipes
Annex C (informative) - Determination of design values for
the radial thermal resistance
Annex D (informative) - Guideline for testing
Bibliography
Gives classification, general requirements and test methods for flexible, pre-insulated, directly buried district heating pipe systems.
| DevelopmentNote |
2009 Edition Re-Issued in January 2015 & incorporates AMD 1 2014. (02/2015)
|
| DocumentType |
Standard
|
| Pages |
34
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| EN 15632-1:2009+A1:2014 | Identical |
| EN 13941:2009+A1:2010 | Design and installation of preinsulated bonded pipe systems for district heating |
| EN 12667:2001 | Thermal performance of building materials and products - Determination of thermal resistance by means of guarded hot plate and heat flow meter methods - Products of high and medium thermal resistance |
| EN 12085:2013 | Thermal insulating products for building applications - Determination of linear dimensions of test specimens |
| EN 1295-1:1997 | Structural design of buried pipelines under various conditions of loading - Part 1: General requirements |
| EN ISO 23993:2010 | Thermal insulation products for building equipment and industrial installations - Determination of design thermal conductivity (ISO 23993:2008, Corrected version 2009-10-01) |
| EN 1606:2013 | Thermal insulating products for building applications - Determination of compressive creep |
| IEC 60811-4-1:2004 | Insulating and sheathing materials of electric and optical cables - Common test methods - Part 4-1: Methods specific to polyethylene and polypropylene compounds - Resistance to environmental stress cracking - Measurement of the melt flow index - Carbon black and/or mineral filler content measurement in polyethylene by direct combustion - Measurement of carbon black content by thermogravimetric analysis (TGA) - Assessment of carbon black dispersion in polyethylene using a microscope |
| EN ISO 9967:2016 | Thermoplastics pipes - Determination of creep ratio (ISO 9967:2016) |
| EN 728:1997 | Plastics piping and ducting systems - Polyolefin pipes and fittings - Determination of oxidation induction time |
| EN ISO 8497:1996 | Thermal insulation - Determination of steady-state thermal transmission properties of thermal insulation for circular pipes (ISO 8497:1994) |
| ISO 23993:2008 | Thermal insulation products for building equipment and industrial installations — Determination of design thermal conductivity |
| ISO 16770:2004 | Plastics Determination of environmental stress cracking (ESC) of polyethylene Full-notch creep test (FNCT) |
| EN 1605:2013 | Thermal insulating products for building applications - Determination of deformation under specified compressive load and temperature conditions |
| EN ISO 16871:2003 | Plastics piping and ducting systems - Plastics pipes and fittings - Method for exposure to direct (natural) weathering (ISO 16871:2003) |
| ISO 6964:1986 | Polyolefin pipes and fittings Determination of carbon black content by calcination and pyrolysis Test method and basic specification |
| ISO 8497:1994 | Thermal insulation — Determination of steady-state thermal transmission properties of thermal insulation for circular pipes |
| EN 14419:2009 | District heating pipes - Preinsulated bonded pipe systems for directly buried hot water networks - Surveillance systems |
| ISO 16871:2003 | Plastics piping and ducting systems — Plastics pipes and fittings — Method for exposure to direct (natural) weathering |
| EN 489:2009 | District heating pipes - Preinsulated bonded pipe systems for directly buried hot water networks - Joint assembly for steel service pipes, polyurethane thermal insulation and outer casing of polyethylene |
| EN ISO 9969:2016 | Thermoplastics pipes - Determination of ring stiffness (ISO 9969:2016) |
| EN 744:1995 | Plastics piping and ducting systems - Thermoplastics pipes - Test method for resistance to external blows by the round-the-clock method |
| EN 60811-4-1:2004 | Insulating and sheathing materials of electric and optical cables - Common test methods - Part 4-1: Methods specific to polyethylene and polypropylene compounds - Resistance to environmental stress cracking - Measurement of the melt flow index - Carbon black and/or mineral filler content measurement in polyethylene by direct combustion - Measurement of carbon black content by thermogravimetric analysis (TGA) - Assessment of carbon black dispersion in polyethylene using a microscope |
| ISO 9967:2016 | Thermoplastics pipes Determination of creep ratio |
| EN 253:2009+A2:2015 | District heating pipes - Preinsulated bonded pipe systems for directly buried hot water networks - Pipe assembly of steel service pipe, polyurethane thermal insulation and outer casing of polyethylene |
| ISO 9969:2016 | Thermoplastics pipes Determination of ring stiffness |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.