I.S. EN 15600-1:2010
Current
The latest, up-to-date edition.
THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - IN-SITU THERMAL INSULATION FORMED FROM EXFOLIATED VERMICULITE (EV) PRODUCTS - PART 1: SPECIFICATION FOR BONDED AND LOOSE-FILL PRODUCTS BEFORE INSTALLATION
Hardcopy , PDF
English
01-01-2010
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
1 Scope
2 Normative references
3 Terms and Definitions, Symbols and Abbreviations
4 Requirements
5 Test methods
6 Designation Code
7 Evaluation of conformity
8 Marking and labelling
Annex A (normative) - Factory production control
Annex B (normative) - Preparation of the test specimens to
measure thermal conductivity
Annex C (normative) - Special conditions to be used for the
determination of organic content
Annex D (normative) - Determination of maximum service
temperature
Annex ZA (informative) - Clauses of this European Standard
addressing the provisions of the EU Construction
Products Directive
Bibliography
Describes the requirements for exfoliated vermiculite products which are used for the thermal insulation of building equipment and industrial installations with an operating temperature in the range of approximately -40 degrees C to +1050 degrees C.
| DocumentType |
Standard
|
| Pages |
27
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Current
|
| Standards | Relationship |
| EN 15600-1:2010 | Identical |
| ISO 9229:2007 | Thermal insulation Vocabulary |
| EN 12667:2001 | Thermal performance of building materials and products - Determination of thermal resistance by means of guarded hot plate and heat flow meter methods - Products of high and medium thermal resistance |
| EN 932-2:1999 | Tests for general properties of aggregates - Part 2: Methods for reducing laboratory samples |
| ISO 13787:2003 | Thermal insulation products for building equipment and industrial installations Determination of declared thermal conductivity |
| EN 14706:2012 | Thermal insulating products for building equipment and industrial installations - Determination of maximum service temperature |
| EN 13468:2001 | Thermal insulating products for building equipment and industrial installations - Determination of trace quantities of water soluble chloride, fluoride, silicate, sodium ions and pH |
| EN 13820:2003 | Thermal insulating materials for building applications - Determination of organic content |
| EN ISO 9229:2007 | Thermal insulation - Vocabulary (ISO 9229:2007) |
| EN ISO 13787:2003 | Thermal insulation products for building equipment and industrial installations - Determination of declared thermal conductivity (ISO 13787:2003) |
| EN 1097-3:1998 | Tests for mechanical and physical properties of aggregates - Part 3: Determination of loose bulk density and voids |
| EN 933-1:2012 | Tests for geometrical properties of aggregates - Part 1: Determination of particle size distribution - Sieving method |
| EN 15600-2:2010 | Thermal insulation products for building equipment and industrial installations - In-situ thermal insulation formed from exfoliated vermiculite (EV) products - Part 2: Specification for the installed products |
| EN 14317-2:2007 | Thermal insulation products for buildings - In-situ thermal insulation formed from exfoliated vermiculite (EV) products - Part 2: Specification for the installed products |
| EN 13055-2:2004 | Lightweight aggregates - Part 2: Lightweight aggregates for bituminous mixtures and surface treatments and for unbound and bound applications |
| EN 12086:2013 | Thermal insulating products for building applications - Determination of water vapour transmission properties |
| EN 13172:2012 | Thermal insulation products - Evaluation of conformity |
| EN 932-1:1996 | Tests for general properties of aggregates - Part 1: Methods for sampling |
| EN 993-14 : 1998 | METHODS OF TESTING DENSE SHAPED REFRACTORY PRODUCTS - PART 14: DETERMINATION OF THERMAL CONDUCTIVITY BY THE HOT-WIRE (CROSS-ARRAY) METHOD |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.