I.S. EN 14409-3:2004
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND WATER SUPPLY NETWORKS - PART 3: LINING WITH CLOSE FIT-PIPES
Hardcopy , PDF
05-11-2011
English
01-01-2004
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
1 Scope
2 Normative references
3 Terms, definitions, symbols and abbreviations
4 Pipes at the "M" stage
5 Fittings at the "M" stage
6 Valves
7 Fitness for purpose of the lining system at the "I" stage
8 Installation practice
Annex A (informative) Guidance for assessment of conformity
Annex B (normative) Factory folded heat reverted polyethylene
(PE) pipe - Determination of memory ability
Annex C (informative) Folded polyethylene (PE) pipe -
Determination of resistance to circumferential
tensile stress at constant temperature
Bibliography
Gives requirements and test methods for close-fit lining systems intended to be used for the renovation of water supply networks of water intended for human consumption, including raw water intake pipelines.
| DocumentType |
Standard
|
| Pages |
29
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| NEN EN 14409-3 : 2004 | Identical |
| SN EN 14409-3 : 2005 | Identical |
| UNE-EN 14409-3:2005 | Identical |
| DIN EN 14409-3:2004-12 | Identical |
| EN 14409-3:2004 | Identical |
| NBN EN 14409-3 : 2004 | Identical |
| UNI EN 14409-3 : 2005 | Identical |
| NS EN 14409-3 : 1ED 2004 | Identical |
| NF EN 14409-3 : 2005 | Identical |
| BS EN 14409-3:2004 | Identical |
| EN 12201-4:2012 | Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 4: Valves |
| EN 12201-3:2011+A1:2012 | Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 3: Fittings |
| ISO 12176-1:2017 | Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 1: Butt fusion |
| ISO 3:1973 | Preferred numbers Series of preferred numbers |
| EN 14409-1:2004 | Plastics piping systems for renovation of underground water supply networks - Part 1: General |
| ISO 12176-2:2008 | Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 2: Electrofusion |
| ISO/TR 11295:1992 | Techniques for rehabilitation of pipeline sytems by the use of plastics pipes and fittings |
| ISO 3126:2005 | Plastics piping systems Plastics components Determination of dimensions |
| EN 921:1994/AC:1995 | PLASTICS PIPING SYSTEMS - THERMOPLASTICS PIPES - DETERMINATION OF RESISTANCE TO INTERNAL PRESSURE AT CONSTANT TEMPERATURE |
| EN 12201-5:2011 | Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 5: Fitness for purpose of the system |
| EN 13689 : 2002 | GUIDANCE ON THE CLASSIFICATION AND DESIGN OF PLASTICS PIPING SYSTEMS USED FOR RENOVATION |
| EN 12201-2:2011+A1:2013 | Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 2: Pipes |
| PREN ISO 3126 : DRAFT 1999 | PLASTICS PIPING SYSTEMS - PLASTICS PIPING COMPONENTS - MEASUREMENT AND DETERMINATION OF DIMENSIONS |
| ISO 497:1973 | Guide to the choice of series of preferred numbers and of series containing more rounded values of preferred numbers |
| ISO 899-1:2017 | Plastics — Determination of creep behaviour — Part 1: Tensile creep |
| EN 12201-1:2011 | Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 1: General |
| CEN/TS 12201-7:2014 | Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 7: Guidance for the assessment of conformity |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.