I.S. EN 14394:2006
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
View Superseded by
HEATING BOILERS - HEATING BOILERS WITH FORCED DRAUGHT BURNERS - NOMINAL HEAT OUTPUT NOT EXCEEDING 10 MW AND MAXIMUM OPERATING TEMPERATURE OF 110 DEGREE C
Hardcopy , PDF
09-15-2008
English
02-22-2006
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Requirements
5 Materials
6 Design
7 Tests
8 Performance requirements
9 Technical documentation
Annex A (normative) Cylindrical shells under internal
pressure
Annex B (normative) Spherical shells and dished heads
under internal and external pressure
Annex C (normative) Dished fire tube heads
Annex D (normative) Flat walls, stayings and girder stays
Annex E (normative) Cylindrical shells under external
pressure
Annex F (informative) Pressure Equipment Directive 97/23/EC
Annex ZA (informative) Relationship between this European
Standard and the Essential Requirements
of EU Directive 92/42/EEC of 21 May
1992 on efficiency requirements for
new hot-water boilers fired with
liquid or gaseous fuels
Annex ZB (informative) Relationship between this European Standard
and the Essential Requirements of EU
Directive 97/23/EC concerning pressure
equipment (PED)
Bibliography
Describes the requirements and test methods for the design, manufacturing, safe operation and the rational energy usage for standard boilers and low temperature boilers (with "boiler" in the sense of "boiler body") from steel and cast iron to be equipped with separately marketed forced draught burners according to the relevant burner standards (for automatic forced draught burners for gaseous fuels see EN 676 and for atomising oil burners see EN 267) up to a nominal heat output of 10 MW.
| DevelopmentNote |
2006 Edition Re-Issued in September 2008 & incorporates AMD 1 2008. (09/2008)
|
| DocumentType |
Standard
|
| Pages |
127
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Withdrawn
|
| SupersededBy |
| Standards | Relationship |
| DIN EN 14394:2008-12 | Identical |
| UNI EN 14394 : 2008 | Identical |
| BS EN 14394 : 2005 | Identical |
| UNE-EN 14394:2006 | Identical |
| EN 14394:2005+A1:2008 | Identical |
| NF EN 14394 : 2006 + A1 2008 | Identical |
| NEN EN 14394 : 2005 + A1 2008 | Identical |
| SN EN 14394 : 2006 + A1 2008 | Identical |
| NBN EN 14394 : 2006 + A1 2009 | Identical |
| NS EN 14394 : 2005 + A1 2008 | Identical |
| EN 12953-9:2007 | Shell boilers - Part 9: Requirements for limiting devices of the boiler and accessories |
| EN 12953-5:2002 | Shell boilers - Part 5: Inspection during construction, documentation and marking of pressure parts of the boiler |
| ISO 2553:2013 | Welding and allied processes Symbolic representation on drawings Welded joints |
| EN ISO 6506-1:2014 | Metallic materials - Brinell hardness test - Part 1: Test method (ISO 6506-1:2014) |
| ISO 6506-1:2014 | Metallic materials Brinell hardness test Part 1: Test method |
| IEC 60730-2-9:2015 RLV | Automatic electrical controls - Part 2-9: Particular requirements for temperature sensing controls |
| EN ISO 228-2:2003 | Pipe threads where pressure-tight joints are not made on the threads - Part 2: Verification by means of limit gauges (ISO 228-2:1987) |
| EN 12953-12:2003 | Shell boilers - Part 12: Requirements for grate firing systems for solid fuels for the boiler |
| ISO 7005-2:1988 | Metallic flanges — Part 2: Cast iron flanges |
| ISO 9606-2:2004 | Qualification test of welders — Fusion welding — Part 2: Aluminium and aluminium alloys |
| EN 10216-5:2013 | Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 5: Stainless steel tubes |
| EN 12953-6:2011 | Shell Boilers - Part 6: Requirements for equipment for the boiler |
| EN ISO 15613:2004 | Specification and qualification of welding procedures for metallic materials - Qualification based on pre-production welding test (ISO 15613:2004) |
| ISO 15614-2:2005 | Specification and qualification of welding procedures for metallic materials Welding procedure test Part 2: Arc welding of aluminium and its alloys |
| EN ISO 15612:2004 | Specification and qualification of welding procedures for metallic materials - Qualification by adoption of a standard welding procedure (ISO 15612:2004) |
| ISO 15610:2003 | Specification and qualification of welding procedures for metallic materials — Qualification based on tested welding consumables |
| EN 304:2017 | Heating boilers - Test code for heating boilers for atomizing oil burners |
| EN 60730-2-9:2010 | Automatic electrical controls for household and similar use - Part 2-9: Particular requirements for temperature sensing controls |
| ISO 7005-3:1988 | Metallic flanges Part 3: Copper alloy and composite flanges |
| EN ISO 4063:2010 | Welding and allied processes - Nomenclature of processes and reference numbers (ISO 4063:2009, Corrected version 2010-03-01) |
| EN 303-1:2017 | Heating boilers - Part 1: Heating boilers with forced draught burners - Terminology, general requirements, testing and marking |
| EN 10216-2:2013 | Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 2: Non-alloy and alloy steel tubes with specified elevated temperature properties |
| EN 10025-1:2004 | Hot rolled products of structural steels - Part 1: General technical delivery conditions |
| EN 10088-2:2014 | Stainless steels - Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes |
| EN 267:2009+A1:2011 | Automatic forced draught burners for liquid fuels |
| EN 303-2:2017 | Heating boilers - Part 2: Heating boilers with forced draught burners - Special requirements for boilers with atomizing oil burners |
| ISO 15612:2004 | Specification and qualification of welding procedures for metallic materials Qualification by adoption of a standard welding procedure |
| EN 12953-1:2012 | Shell boilers - Part 1: General |
| EN 12953-7:2002 | Shell boilers - Part 7 : Requirements for firing systems for liquid and gaseous fuels for the boilers |
| EN ISO 15611:2003 | Specification and qualification of welding procedures for metallic materials - Qualification based on previous welding experience (ISO 15611:2003) |
| EN ISO 228-1:2003 | Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000) |
| EN 10217-7:2014 | Welded steel tubes for pressure purposes - Technical delivery conditions - Part 7: Stainless steel tubes |
| ISO 15614-1:2017 | Specification and qualification of welding procedures for metallic materials — Welding procedure test — Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys |
| ISO 15609-1:2004 | Specification and qualification of welding procedures for metallic materials Welding procedure specification Part 1: Arc welding |
| ISO 15611:2003 | Specification and qualification of welding procedures for metallic materials — Qualification based on previous welding experience |
| EN 12953-3:2016 | Shell boilers - Part 3: Design and calculation for pressure parts |
| EN 12953-11:2003 | Shell boilers - Part 11: Acceptance tests |
| EN 10021:2006 | General technical delivery conditions for steel products |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| EN 22553:1994 | Welded, brazed and soldered joints - Symbolic representation on drawings (ISO 2553:1992) |
| EN ISO 15614-2:2005 | Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 2: Arc welding of aluminium and its alloys (ISO 15614-2:2005) |
| EN 12953-2:2012 | Shell boilers - Part 2: Materials for pressure parts of boilers and accessories |
| EN ISO 9606-2:2004 | Qualification test of welders - Fusion welding - Part 2: Aluminium and aluminium alloys (ISO 9606-2:2004) |
| ISO 857-1:1998 | Welding and allied processes Vocabulary Part 1: Metal welding processes |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| EN 12828:2012+A1:2014 | Heating systems in buildings - Design for water-based heating systems |
| EN 1563:2011 | Founding - Spheroidal graphite cast irons |
| EN ISO 15609-1:2004 | Specification and qualification of welding procedures for metallic materials - Welding procedure specification - Part 1: Arc welding (ISO 15609-1:2004) |
| EN 10226-3:2005 | Pipes threads where pressure tight joint are made on the threads - Part 3: Verification by means of limit gauges |
| EN 303-7:2006 | Heating boilers - Part 7: Gas-fired central heating boilers equipped with a forced draught burner of nominal heat output not exceeding 1 000 kW |
| ISO 185:2005 | Grey cast irons Classification |
| EN 12953-10:2003 | Shell boilers - Part 10 : Requirements for feedwater and boiler water quality |
| EN 60335-1:2012/A13:2017 | HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60335-1:2010, MODIFIED) |
| ISO 228-2:1987 | Pipe threads where pressure-tight joints are not made on the threads Part 2: Verification by means of limit gauges |
| EN 10216-1:2013 | Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 1: Non-alloy steel tubes with specified room temperature properties |
| ISO 7005-1:2011 | Pipe flanges — Part 1: Steel flanges for industrial and general service piping systems |
| EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
| ISO 15613:2004 | Specification and qualification of welding procedures for metallic materials Qualification based on pre-production welding test |
| ISO 4063:2009 | Welding and allied processes — Nomenclature of processes and reference numbers |
| EN ISO 15610:2003 | Specification and qualification of welding procedures for metallic materials - Qualification based on tested welding consumables (ISO 15610:2003) |
| ISO 15607:2003 | Specification and qualification of welding procedures for metallic materials General rules |
| EN 10226-1:2004 | Pipe threads where pressure tight joints are made on the threads - Part 1: Taper external threads and parallel internal threads - Dimensions, tolerances and designation |
| EN 10025-3:2004 | Hot rolled products of structural steels - Part 3: Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steels |
| ISO 228-1:2000 | Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation |
| EN ISO 15607:2003 | Specification and qualification of welding procedures for metallic materials - General rules (ISO 15607:2003) |
| EN 1561:2011 | Founding - Grey cast irons |
| EN 10216-3:2013 | Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 3: Alloy fine grain steel tubes |
| EN 10088-1:2014 | Stainless steels - Part 1: List of stainless steels |
| EN 287-1:2011 | Qualification test of welders - Fusion welding - Part 1: Steels |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.