I.S. EN 13924-1:2015
Current
The latest, up-to-date edition.
BITUMEN AND BITUMINOUS BINDERS - SPECIFICATION FRAMEWORK FOR SPECIAL PAVING GRADE BITUMEN - PART 1: HARD PAVING GRADE BITUMENS
Hardcopy , PDF
English
01-01-2015
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
National Foreword
European foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Sampling
5 Requirements and test methods
6 Assessment and verification of constancy of performance - AVCP
Annex A (normative) - Calculation of the penetration index
Annex B (informative) - Informative properties
Annex ZA (informative) - Clauses of this European Standard
addressing the provisions of the EU
Construction Products Regulation
Bibliography
Gives a framework for specifying the properties and relevant test method for hard paving grade bitumens which are suitable for use in the construction and Maintenance of roads , airfields and other paved areas.
| DevelopmentNote |
Supersedes I.S. EN 13924. (01/2016)
|
| DocumentType |
Standard
|
| Pages |
34
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| EN 13924-1:2015 | Identical |
| EN 12592:2014 | Bitumen and bituminous binders - Determination of solubility |
| EN 1426:2015 | Bitumen and bituminous binders - Determination of needle penetration |
| ISO 2719:2016 | Determination of flash point — Pensky-Martens closed cup method |
| EN 12697-12:2008 | Bituminous mixtures - Test methods for hot mix asphalt - Part 12: Determination of the water sensitivity of bituminous specimens |
| ISO/IEC Guide 62:1996 | General requirements for bodies operating assessment and certification/registration of quality systems |
| EN 12697-1 : 2012 COR 2012 | BITUMINOUS MIXTURES - TEST METHODS FOR HOT MIX ASPHALT - PART 1: SOLUBLE BINDER CONTENT |
| EN 12596:2014 | Bitumen and bituminous binders - Determination of dynamic viscosity by vacuum capillary |
| EN 12697-11:2012 | Bituminous mixtures - Test methods for hot mix asphalt - Part 11: Determination of the affinity between aggregate and bitumen |
| EN 1427:2015 | Bitumen and bituminous binders - Determination of the softening point - Ring and Ball method |
| EN 15326:2007+A1:2009 | Bitumen and bituminous binders - Measurement of density and specific gravity - Capillary-stoppered pyknometer method |
| EN 14770:2012 | Bitumen and bituminous binders - Determination of complex shear modulus and phase angle - Dynamic Shear Rheometer (DSR) |
| EN 12597:2014 | Bitumen and bituminous binders - Terminology |
| EN 12697-26:2012 | Bituminous mixtures - Test methods for hot mix asphalt - Part 26: Stiffness |
| EN 58:2012 | Bitumen and bituminous binders - Sampling bituminous binders |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| ISO 4259:2006 | Petroleum products Determination and application of precision data in relation to methods of test |
| EN 12594:2014 | Bitumen and bituminous binders - Preparation of test samples |
| ISO 9001:2015 | Quality management systems — Requirements |
| EN 12607-3:2014 | Bitumen and bituminous binders - Determination of the resistance to hardening under influence of heat and air - Part 3: RFT method |
| EN ISO 2719:2016 | Determination of flash point - Pensky-Martens closed cup method (ISO 2719:2016) |
| EN 12607-1:2014 | Bitumen and bituminous binders - Determination of the resistance to hardening under influence of heat and air - Part 1: RTFOT method |
| EN 12593:2015 | Bitumen and bituminous binders - Determination of the Fraass breaking point |
| EN ISO 2592:2017 | Petroleum and related products - Determination of flash and fire points - Cleveland open cup method (ISO 2592:2017) |
| EN 12591:2009 | Bitumen and bituminous binders - Specifications for paving grade bitumens |
| EN 14771:2012 | Bitumen and bituminous binders - Determination of the flexural creep stiffness - Bending Beam Rheometer (BBR) |
| EN ISO 4259:2006 | Petroleum products - Determination and application of precision data in relation to methods of test (ISO 4259:2006) |
| EN 12595:2014 | Bitumen and bituminous binders - Determination of kinematic viscosity |
| CEN/TR 15352:2006 | Bitumen and bituminous binders - Development of performance-related specifications: status report 2005 |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.