I.S. EN 13617-1:2012
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PETROL FILLING STATIONS - PART 1: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF METERING PUMPS, DISPENSERS AND REMOTE PUMPING UNITS
Available format(s)
Hardcopy , PDF
Superseded date
10-09-2021
Superseded by
Language(s)
English
Published date
01-01-2012
Publisher
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of significant hazards
5 Safety requirements and/or protective measures
6 Tests
7 Information for use
Annex A (normative) - Classification of vapour barriers
Annex B (informative) - Information on explosion protected
equipment
Annex C (informative) - Environmental aspects
Annex ZA (informative) - Relationship between this European
Standard and the Essential Requirements of EU
Directive 94/9/EC
Annex ZB (informative) - Relationship between this European
Standard and the Essential Requirements of EU
Directive 2006/42/EC
Bibliography
Describes all significant hazards, hazardous situations and events relevant to metering pumps, dispensers and remote pumping units, when they are used as intended and under the conditions foreseeable by the manufacturer.
| DocumentType |
Standard
|
| Pages |
54
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| DIN EN 13617-1:2012-08 | Identical |
| UNI EN 13617-1 : 2012 | Identical |
| NBN EN 13617-1 : 2012 | Identical |
| UNE-EN 13617-1:2012 | Identical |
| NEN EN 13617-1 : 2012 | Identical |
| NS EN 13617-1 : 2012 | Identical |
| BS EN 13617-1:2012 | Identical |
| EN 13617-1:2012 | Identical |
| NF EN 13617-1 : 2012 | Identical |
| SN EN 13617-1 : 2012 | Identical |
| ONORM EN 13617-1 : 2012 | Identical |
| IEC 60950-1:2005+AMD1:2009+AMD2:2013 CSV | Information technology equipment - Safety - Part 1: General requirements |
| EN 1127-1:2011 | Explosive atmospheres - Explosion prevention and protection - Part 1: Basic concepts and methodology |
| IEC 60079-1:2014 RLV | Explosive atmospheres - Part 1: Equipment protection by flameproof enclosures "d" |
| CEN/TS 15293:2011 | Automotive fuels - Ethanol (E85) automotive fuel - Requirements and test methods |
| EN 60079-26:2015 | Explosive atmospheres - Part 26: Equipment with Equipment Protection Level (EPL) Ga |
| EN 60079-1:2014 | Explosive atmospheres - Part 1: Equipment protection by flameproof enclosures "d" |
| EN 60079-10-1:2015 | Explosive atmospheres - Part 10-1: Classification of areas - Explosive gas atmospheres |
| ISO 9329-3:1997 | Seamless steel tubes for pressure purposes — Technical delivery conditions — Part 3: Unalloyed and alloyed steels with specified low temperature properties |
| EN 228:2012+A1:2017 | Automotive fuels - Unleaded petrol - Requirements and test methods |
| ISO 1825:2010 | Rubber hoses and hose assemblies for aircraft ground fuelling and defuelling Specification |
| IEC 60730-2-10:2006 | Automatic electrical controls for household and similar use - Part 2-10: Particular requirements for motor-starting relays |
| EN 1057:2006+A1:2010 | Copper and copper alloys - Seamless, round copper tubes for water and gas in sanitary and heating applications |
| EN 60079-0:2012/A11:2013 | EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS (IEC 60079-0:2011, MODIFIED) |
| EN 13617-2:2012 | Petrol filling stations - Part 2: Safety requirements for construction and performance of safe breaks for use on metering pumps and dispensers |
| EN 60079-15:2010 | Explosive atmospheres - Part 15: Equipment protection by type of protection "n" |
| EN 13483:2013 | Rubber and plastic hoses and hose assemblies with internal vapour recovery for measured fuel dispensing systems - Specification |
| EN 13463-1:2009 | Non-electrical equipment for use in potentially explosive atmospheres - Part 1: Basic method and requirements |
| IEC 60204-1:2016 | Safety of machinery - Electrical equipment of machines - Part 1: General requirements |
| IEC 60079-18:2014 RLV | Explosive atmospheres - Part 18: Equipment protection by encapsulation “m” |
| EN 60950-1:2006/A2:2013 | INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60950-1:2005/A2:2013, MODIFIED) |
| EN ISO 1182:2010 | Reaction to fire tests for products - Non-combustibility test (ISO 1182:2010) |
| EN 13617-3:2012 | Petrol filling stations - Part 3: Safety requirements for construction and performance of shear valves |
| ISO 9329-1:1989 | Seamless steel tubes for pressure purposes — Technical delivery conditions — Part 1: Unalloyed steels with specified room temperature properties |
| IEC 60079-10-1:2015 | Explosive atmospheres - Part 10-1: Classification of areas - Explosive gas atmospheres |
| EN 60079-6:2015 | Explosive atmospheres - Part 6: Equipment protection by liquid immersion "o" |
| ISO 12100:2010 | Safety of machinery — General principles for design — Risk assessment and risk reduction |
| ISO 9329-4:1997 | Seamless steel tubes for pressure purposes — Technical delivery conditions — Part 4: Austenitic stainless steels |
| IEC 60079-5:2015 RLV | Explosive atmospheres - Part 5: Equipment protection by powder filling "q" |
| EN 14125:2013 | Thermoplastic and flexible metal pipework for underground installation at petrol filling stations |
| ISO 1182:2010 | Reaction to fire tests for products Non-combustibility test |
| EN 60947-3:2009/A2:2015 | LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 3: SWITCHES, DISCONNECTORS, SWITCH-DISCONNECTORS AND FUSE-COMBINATION UNITS (IEC 60947-3:2008/A2:2015) |
| EN 60079-11:2012 | Explosive atmospheres - Part 11: Equipment protection by intrinsic safety "i" |
| IEC 60079-11:2011 | Explosive atmospheres - Part 11: Equipment protection by intrinsic safety "i" |
| ISO 9329-2:1997 | Seamless steel tubes for pressure purposes — Technical delivery conditions — Part 2: Unalloyed and alloyed steels with specified elevated temperature properties |
| ISO 11925-3:1997 | Reaction to fire tests — Ignitability of building products subjected to direct impingement of flame — Part 3: Multi-source test |
| EN 60079-25:2010/AC:2013 | EXPLOSIVE ATMOSPHERES - PART 25: INTRINSICALLY SAFE ELECTRICAL SYSTEMS (IEC 60079-25:2010) |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| IEC 60079-25:2010 | Explosive atmospheres - Part 25: Intrinsically safe electrical systems |
| IEC 60079-6:2015 | Explosive atmospheres - Part 6: Equipment protection by liquid immersion "o" |
| IEC 60079-0:2011 | Explosive atmospheres - Part 0: Equipment - General requirements |
| ISO 16852:2016 | Flame arresters — Performance requirements, test methods and limits for use |
| IEC 60079-14:2013 | Explosive atmospheres - Part 14: Electrical installations design, selection and erection |
| EN ISO 12100:2010 | Safety of machinery - General principles for design - Risk assessment and risk reduction (ISO 12100:2010) |
| EN 60079-14:2014/AC:2016 | EXPLOSIVE ATMOSPHERES - PART 14: ELECTRICAL INSTALLATIONS DESIGN, SELECTION AND ERECTION (IEC 60079-14:2013/COR1:2016) |
| EN ISO 13849-1:2015 | Safety of machinery - Safety-related parts of control systems - Part 1: General principles for design (ISO 13849-1:2015) |
| EN 60079-5:2015 | Explosive atmospheres - Part 5: Equipment protection by powder filling "q" |
| EN 13012:2012 | Petrol filling stations - Construction and performance of automatic nozzles for use on fuel dispensers |
| IEC 60947-3:2008+AMD1:2012+AMD2:2015 CSV | Low-voltage switchgear and controlgear - Part 3: Switches, disconnectors, switch-disconnectors and fuse-combination units |
| EN 1360:2013 | Rubber and plastic hoses and hose assemblies for measured fuel dispensing systems - Specification |
| EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
| ISO 13849-1:2015 | Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design |
| EN 60730-2-10:2007 | Automatic electrical controls for household and similar use - Part 2-10: Particular requirements for motor-starting relays |
| IEC 60079-15:2010 | Explosive atmospheres - Part 15: Equipment protection by type of protection "n" |
| IEC 60079-26:2014 RLV | Explosive atmospheres - Part 26: Equipment with Equipment Protection Level (EPL) Ga |
| EN ISO 16852:2016 | Flame arresters - Performance requirements, test methods and limits for use (ISO 16852:2016) |
| CLC/TR 50404:2003 | Electrostatics - Code of practice for the avoidance of hazards due to static electricity |
| EN 60204-1 : 2006 COR 2010 | SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS |
| EN 60079-2:2014/AC:2015 | EXPLOSIVE ATMOSPHERES - PART 2: EQUIPMENT PROTECTION BY PRESSURIZED ENCLOSURE 'P' (IEC 60079-2:2014) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.