I.S. EN 13480-8:2017&LC:2019
Current
Current
The latest, up-to-date edition.
METALLIC INDUSTRIAL PIPING - PART 8: ADDITIONAL REQUIREMENTS FOR ALUMINIUM AND ALUMINIUM ALLOY PIPING
Available format(s)
Hardcopy , PDF
Language(s)
English
Published date
01-01-2017
Publisher
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
National Foreword
European foreword
1 Scope
2 Normative references
3 Terms, definitions, symbols and units
4 General requirements
5 Materials
6 Design
7 Fabrication and installation
8 Inspection and testing
9 Final assessment and documentation
Annex A (informative) - Dimensional tolerances
Annex B (normative) - Transition joints
Annex C (normative) - Nominal design stress values
Annex Y (informative) - History of EN 13480-8
Annex ZA (informative) - Relationship between this
European Standard and the Essential
Requirements of EU Directive 2014/68/EU
aimed to be covered
Bibliography
Defines requirements for industrial piping systems made of aluminium and aluminium alloys in addition to the general requirements for industrial piping according to the series of standards EN 13480 and CEN/TR 13480-7.
| Committee |
CEN/TC 267
|
| DocumentType |
Standard
|
| Pages |
52
|
| ProductNote |
CORRECTION VERSION IS AVAILABLE FOR THIS STANDARD NOTE: The date of any NSAI previous adoption may not match the date of its original CEN/CENELEC document.
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Current
|
| Standards | Relationship |
| BS EN 13480-8:2017 | Identical |
| DIN EN 13480-8:2014-12 | Identical |
| UNI EN 13480-8 : 2014 | Identical |
| NS EN 13480-8 : 2017 | Identical |
| NBN EN 13480-8 : 2012 AMD 2 2015 | Identical |
| NEN EN 13480-8 : 2017 | Identical |
| EN 13480-8:2017 | Identical |
| ISO 16823:2012 | Non-destructive testing — Ultrasonic testing — Transmission technique |
| ISO 17636-1:2013 | Non-destructive testing of welds — Radiographic testing — Part 1: X- and gamma-ray techniques with film |
| ISO 16828:2012 | Non-destructive testing — Ultrasonic testing — Time-of-flight diffraction technique as a method for detection and sizing of discontinuities |
| EN 13480-2:2017 | Metallic industrial piping - Part 2: Materials |
| EN ISO 16811:2014 | Non-destructive testing - Ultrasonic testing - Sensitivity and range setting (ISO 16811:2012) |
| EN ISO 3834-3:2005 | Quality requirements for fusion welding of metallic materials - Part 3: Standard quality requirements (ISO 3834-3:2005) |
| EN ISO 3834-2:2005 | Quality requirements for fusion welding of metallic materials - Part 2: Comprehensive quality requirements (ISO 3834-2:2005) |
| ISO 13920:1996 | Welding — General tolerances for welded constructions — Dimensions for lengths and angles — Shape and position |
| ISO 9606-2:2004 | Qualification test of welders — Fusion welding — Part 2: Aluminium and aluminium alloys |
| EN ISO 16827:2014 | Non-destructive testing - Ultrasonic testing - Characterization and sizing of discontinuities (ISO 16827:2012) |
| EN ISO 16826:2014 | Non-destructive testing - Ultrasonic testing - Examination for discontinuities perpendicular to the surface (ISO 16826:2012) |
| ISO 11666:2010 | Non-destructive testing of welds Ultrasonic testing Acceptance levels |
| EN ISO 10893-11:2011 | Non-destructive testing of steel tubes - Part 11: Automated ultrasonic testing of the weld seam of welded steel tubes for the detection of longitudinal and/or transverse imperfections (ISO 10893-11:2011) |
| ISO 10042:2005 | Welding Arc-welded joints in aluminium and its alloys Quality levels for imperfections |
| EN ISO 3452-1:2013 | Non-destructive testing - Penetrant testing - Part 1: General principles (ISO 3452-1:2013, Corrected version 2014-05-01) |
| ISO 23277:2015 | Non-destructive testing of welds Penetrant testing Acceptance levels |
| EN ISO 6892-1:2016 | Metallic materials - Tensile testing - Part 1: Method of test at room temperature (ISO 6892-1:2016) |
| EN 13480-4:2017 | Metallic industrial piping - Part 4: Fabrication and installation |
| ISO 15614-2:2005 | Specification and qualification of welding procedures for metallic materials Welding procedure test Part 2: Arc welding of aluminium and its alloys |
| EN ISO 16823:2014 | Non-destructive testing - Ultrasonic testing - Transmission technique (ISO 16823:2012) |
| EN 485-3:2003 | Aluminium and aluminium alloys - Sheet, strip and plate - Part 3: Tolerances on dimensions and form for hot-rolled products |
| EN 485-2:2016 | Aluminium and aluminium alloys - Sheet, strip and plate - Part 2: Mechanical properties |
| EN 485-4:1993 | Aluminium and aluminium alloys - Sheet, strip and plate - Part 4: Tolerances on shape and dimensions for cold-rolled products |
| ISO 10893-8:2011 | Non-destructive testing of steel tubes Part 8: Automated ultrasonic testing of seamless and welded steel tubes for the detection of laminar imperfections |
| ISO 6892-1:2016 | Metallic materials Tensile testing Part 1: Method of test at room temperature |
| EN 586-2:1994 | Aluminium and aluminium alloys - Forgings - Part 2: Mechanical properties and additional property requirements |
| EN ISO 4063:2010 | Welding and allied processes - Nomenclature of processes and reference numbers (ISO 4063:2009, Corrected version 2010-03-01) |
| EN ISO 23277:2015 | Non-destructive testing of welds - Penetrant testing - Acceptance levels (ISO 23277:2015) |
| ISO 10893-11:2011 | Non-destructive testing of steel tubes Part 11: Automated ultrasonic testing of the weld seam of welded steel tubes for the detection of longitudinal and/or transverse imperfections |
| EN 13480-1:2017 | Metallic industrial piping - Part 1: General |
| EN 764-5:2014 | Pressure equipment - Part 5: Inspection documentation of metallic materials and compliance with the material specification |
| EN ISO 10893-8:2011 | Non-destructive testing of steel tubes - Part 8: Automated ultrasonic testing of seamless and welded steel tubes for the detection of laminar imperfections (ISO 10893-8:2011) |
| ISO 5173:2009 | Destructive tests on welds in metallic materials — Bend tests |
| EN ISO 16828:2014 | Non-destructive testing - Ultrasonic testing - Time-of-flight diffraction technique as a method for detection and sizing of discontinuities (ISO 16828:2012) |
| EN 13445-8 : 2014 COR 2017 | UNFIRED PRESSURE VESSELS - PART 8: ADDITIONAL REQUIREMENTS FOR PRESSURE VESSELS OF ALUMINIUM AND ALUMINIUM ALLOYS |
| ISO 17640:2017 | Non-destructive testing of welds Ultrasonic testing Techniques, testing levels, and assessment |
| ISO 148-1:2016 | Metallic materials — Charpy pendulum impact test — Part 1: Test method |
| ISO 16827:2012 | Non-destructive testing — Ultrasonic testing — Characterization and sizing of discontinuities |
| ISO 3452-1:2013 | Non-destructive testing Penetrant testing Part 1: General principles |
| ISO 16810:2012 | Non-destructive testing — Ultrasonic testing — General principles |
| ISO 7438:2016 | Metallic materials Bend test |
| EN 13480-3:2017 | Metallic industrial piping - Part 3: Design and calculation |
| EN ISO 16810:2014 | Non-destructive testing - Ultrasonic testing - General principles (ISO 16810:2012) |
| EN 13445-4 : 2014 COR 2017 | UNFIRED PRESSURE VESSELS - PART 4: FABRICATION |
| CEN/TR 13480-7:2017 | Metallic industrial piping - Part 7: Guidance on the use of conformity assessment procedures |
| EN ISO 17637:2016 | Non-destructive testing of welds - Visual testing of fusion-welded joints (ISO 17637:2016) |
| EN 1092-4:2002 | Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 4: Aluminium alloy flanges |
| EN ISO 13920:1996 | Welding - General tolerances for welded constructions - Dimensions for lengths and angles - Shape and position (ISO 13920:1996) |
| EN ISO 17639:2013 | Destructive tests on welds in metallic materials - Macroscopic and microscopic examination of welds (ISO 17639:2003) |
| ISO 3834-2:2005 | Quality requirements for fusion welding of metallic materials Part 2: Comprehensive quality requirements |
| EN ISO 15614-2:2005 | Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 2: Arc welding of aluminium and its alloys (ISO 15614-2:2005) |
| ISO 17636-2:2013 | Non-destructive testing of welds — Radiographic testing — Part 2: X- and gamma-ray techniques with digital detectors |
| ISO 16811:2012 | Non-destructive testing — Ultrasonic testing — Sensitivity and range setting |
| EN ISO 9606-2:2004 | Qualification test of welders - Fusion welding - Part 2: Aluminium and aluminium alloys (ISO 9606-2:2004) |
| ISO 857-1:1998 | Welding and allied processes Vocabulary Part 1: Metal welding processes |
| ISO 17639:2003 | Destructive tests on welds in metallic materials Macroscopic and microscopic examination of welds |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| 2014/68/EU : 2014 COR 1 2015 | DIRECTIVE 2014/68/EU OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 15 MAY 2014 ON THE HARMONISATION OF THE LAWS OF THE MEMBER STATES RELATING TO THE MAKING AVAILABLE ON THE MARKET OF PRESSURE EQUIPMENT TEXT WITH EEA RELEVANCE |
| CEN ISO/TR 15608:2017 | Welding - Guidelines for a metallic materials grouping system (ISO/TR 15608:2017) |
| EN ISO 6892-2:2011 | Metallic materials - Tensile testing - Part 2: Method of test at elevated temperature (ISO 6892-2:2011) |
| ISO 17637:2016 | Non-destructive testing of welds Visual testing of fusion-welded joints |
| EN 12392:2016 | Aluminium and aluminium alloys - Wrought products and cast products - Special requirements for products intended for the production of pressure equipment |
| EN ISO 17636-2:2013 | Non-destructive testing of welds - Radiographic testing - Part 2: X- and gamma-ray techniques with digital detectors (ISO 17636-2:2013) |
| ISO 6892-2:2011 | Metallic materials Tensile testing Part 2: Method of test at elevated temperature |
| EN ISO 4136:2012 | Destructive tests on welds in metallic materials - Transverse tensile test (ISO 4136:2012) |
| ISO 16826:2012 | Non-destructive testing — Ultrasonic testing — Examination for discontinuities perpendicular to the surface |
| ISO 4136:2012 | Destructive tests on welds in metallic materials Transverse tensile test |
| EN ISO 148-1:2016 | Metallic materials - Charpy pendulum impact test - Part 1: Test method (ISO 148-1:2016) |
| ISO 4063:2009 | Welding and allied processes — Nomenclature of processes and reference numbers |
| EN ISO 17636-1:2013 | Non-destructive testing of welds - Radiographic testing - Part 1: X- and gamma-ray techniques with film (ISO 17636-1:2013) |
| EN 14717:2005 | Welding and allied processes - Environmental check list |
| EN 13480-5:2017 | Metallic industrial piping - Part 5: Inspection and testing |
| EN 764-3:2002 | Pressure equipment - Part 3: Definition of parties involved |
| EN 573-3:2013 | Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 3: Chemical composition and form of products |
| EN 764-4:2014 | Pressure equipment - Part 4: Establishment of technical delivery conditions for metallic materials |
| ISO 3834-3:2005 | Quality requirements for fusion welding of metallic materials Part 3: Standard quality requirements |
| EN ISO 7438:2016 | Metallic materials - Bend test (ISO 7438:2016) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.