I.S. EN 13476-2:2007
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY (VINYLCHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 2: SPECIFICATIONS FOR PIPES AND FITTINGS WITH SMOOTH INTERNAL AND EXTERNAL SURFACE AND THE SYSTEM, TYPE A
Hardcopy , PDF
05-06-2018
English
01-01-2007
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
National Foreword
European foreword
Introduction
1 Scope
2 Normative references
3 Terms, definitions, symbols and abbreviations
4 Material
5 Designation of wall constructions and examples of
typical jointing methods
6 Appearance and colour
7 Geometrical characteristics
8 Physical characteristics
9 Mechanical characteristics
10 Performance requirements
11 Marking
Annex A (normative) - Compound/formulation PVC-U material
Annex B (normative) - Utilization of non-virgin PVC-U material
Annex C (normative) - Compound/formulation PP material
Annex D (normative) - Utilization of non-virgin PP material
Annex E (normative) - Compound/formulation for PE material
Annex F (normative) - Utilization of non-virgin PE material
Annex G (normative) - Impact test at 23 degree C
Annex H (normative) - Impact test at - 10 degree C
Annex I (normative) - Ring flexibility test at 20% diametric
deflection
Annex J (informative) - Survey of possible use of
reprocessed and recycled material
Annex K (normative) - Impact test for large diameter pipes
with structured wall
Bibliography
Describes the definitions and requirements for pipes, fittings and the system based on unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene PE) structured-wall piping systems that are intended to be used for non-pressure underground drainage and sewerage systems.
| DocumentType |
Standard
|
| Pages |
46
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| Standards | Relationship |
| BS EN 13476-2:2007 | Identical |
| NS EN 13476-2 : 1ED 2007 | Identical |
| UNE-EN 13476-2:2007 | Identical |
| DIN EN 13476-2:2015-11 (Draft) | Identical |
| NF EN 13476-2 : 2007 | Identical |
| UNI EN 13476-2 : 2008 | Identical |
| ONORM EN 13476-2 : 2015 | Identical |
| SN EN 13476-2 : 2007 | Identical |
| NBN EN 13476-2 : 2007 | Identical |
| DIN EN 13476-2:2007-08 | Identical |
| EN 13476-2:2018 | Identical |
| NEN EN 13476-2 : 2018 | Identical |
| ISO 580:2005 | Plastics piping and ducting systems — Injection-moulded thermoplastics fittings — Methods for visually assessing the effects of heating |
| EN ISO 3126:2005 | Plastics piping systems - Plastics components - Determination of dimensions (ISO 3126:2005) |
| EN ISO 13229:2011 | Thermoplastics piping systems for non-pressure applications - Unplasticized poly(vinyl chloride) (PVC-U) pipes and fittings - Determination of the viscosity number and K-value (ISO 13229:2010) |
| ISO 3451-1:2008 | Plastics Determination of ash Part 1: General methods |
| ISO 13229:2010 | Thermoplastics piping systems for non-pressure applications Unplasticized poly(vinyl chloride) (PVC-U) pipes and fittings Determination of the viscosity number and K-value |
| EN ISO 9967:2016 | Thermoplastics pipes - Determination of creep ratio (ISO 9967:2016) |
| ISO 13263:2010 | Thermoplastics piping systems for non-pressure underground drainage and sewerage Thermoplastics fittings Test method for impact strength |
| EN ISO 1158:1998 | Plastics - Vinyl chloride homopolymers and copolymers - Determination of chlorine content (ISO 1158:1998) |
| ISO 1167-2:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces |
| ISO 1133-1:2011 | Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 1: Standard method |
| ISO 11173:1994 | Thermoplastics pipes — Determination of resistance to external blows — Staircase method |
| ISO 2507-1:1995 | Thermoplastics pipes and fittings — Vicat softening temperature — Part 1: General test method |
| EN ISO 11173:2017 | Thermoplastics pipes - Determination of resistance to external blows - Staircase method (ISO 11173:1994) |
| ISO 3127:1994 | Thermoplastics pipes — Determination of resistance to external blows — Round-the-clock method |
| EN ISO 3451-1:2008 | Plastics - Determination of ash - Part 1: General methods (ISO 3451-1:2008) |
| EN ISO 1167-2:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 2: Preparation of pipe test pieces (ISO 1167-2:2006) |
| EN 15346:2014 | Plastics - Recycled plastics - Characterization of poly(vinyl chloride) (PVC) recyclates |
| EN ISO 1167-1:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 1: General method (ISO 1167-1:2006) |
| ISO 13968:2008 | Plastics piping and ducting systems — Thermoplastics pipes — Determination of ring flexibility |
| EN ISO 6259-1:2015 | Thermoplastics pipes - Determination of tensile properties - Part 1: General test method (ISO 6259-1:2015) |
| EN 14680:2015 | Adhesives for non-pressure thermoplastics piping systems - Specifications |
| EN ISO 3451-5:2002 | Plastics - Determination of ash - Part 5: Poly(vinyl chloride) (ISO 3451-5:2002) |
| ISO 6259-1:2015 | Thermoplastics pipes Determination of tensile properties Part 1: General test method |
| ISO 3126:2005 | Plastics piping systems Plastics components Determination of dimensions |
| EN ISO 9852:2017 | Unplasticized poly(vinyl chloride) (PVC-U) pipes - Dichloromethane resistance at specified temperature (DCMT) - Test method (ISO 9852:2007) |
| EN 476:2011 | General requirements for components used in drains and sewers |
| EN ISO 1133-1:2011 | Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics - Part 1: Standard method (ISO 1133-1:2011) |
| ISO 13260:2010 | Thermoplastics piping systems for non-pressure underground drainage and sewerage Test method for resistance to combined temperature cycling and external loading |
| ISO 13262:2010 | Thermoplastics piping systems for non-pressure underground drainage and sewerage Thermoplastics spirally-formed structured-wall pipes Determination of the tensile strength of a seam |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| EN ISO 3127:2017 | Thermoplastics pipes - Determination of resistance to external blows - Round-the-clock method (ISO 3127:1994) |
| EN 14758-1:2012 | Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene with mineral modifiers (PP-MD) - Part 1: Specifications for pipes, fittings and the system |
| ISO 1158:1998 | Plastics — Vinyl chloride homopolymers and copolymers — Determination of chlorine content |
| EN ISO 13968:2008 | Plastics piping and ducting systems - Thermoplastics pipes - Determination of ring flexibility (ISO 13968:2008) |
| ISO 1183-1:2012 | Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method |
| EN ISO 13967:2009 | Thermoplastics fittings - Determination of ring stiffness (ISO 13967:2009) |
| EN 12666-1:2005+A1:2011 | Plastics piping systems for non-pressure underground drainage and sewerage - Polyethylene (PE) - Part 1: Specifications for pipes, fittings and the system |
| EN ISO 9969:2016 | Thermoplastics pipes - Determination of ring stiffness (ISO 9969:2016) |
| EN ISO 13262:2017 | Thermoplastics piping systems for non-pressure underground drainage and sewerage - Thermoplastics spirally-formed structured-wall pipes - Determination of the tensile strength of a seam (ISO 13262:2010) |
| ISO 9001:2015 | Quality management systems — Requirements |
| EN ISO 580:2005 | Plastics piping and ducting systems - Injection-moulded thermoplastics fittings - Methods for visually assessing the effects of heating (ISO 580:2005) |
| EN ISO 13254:2017 | Thermoplastics piping systems for non-pressure applications - Test method for watertightness (ISO 13254:2010) |
| EN 1401-1:2009 | Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system |
| ISO 11357-6:2008 | Plastics Differential scanning calorimetry (DSC) Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT) |
| ISO 3451-5:2002 | Plastics — Determination of ash — Part 5: Poly(vinyl chloride) |
| ISO 9967:2016 | Thermoplastics pipes Determination of creep ratio |
| EN ISO 2505:2005 | Thermoplastics pipes - Longitudinal reversion - Test method and parameters (ISO 2505:2005) |
| ISO 13967:2009 | Thermoplastics fittings Determination of ring stiffness |
| ISO 13257:2010 | Thermoplastics piping systems for non-pressure applications Test method for resistance to elevated temperature cycling |
| EN ISO 13257:2017 | Thermoplastics piping systems for non-pressure applications - Test method for resistance to elevated temperature cycling (ISO 13257:2010) |
| ISO 13254:2010 | Thermoplastics piping systems for non-pressure applications Test method for watertightness |
| ISO 13264:2010 | Thermoplastics piping systems for non-pressure underground drainage and sewerage Thermoplastics fittings Test method for mechanical strength or flexibility of fabricated fittings |
| ISO 9969:2016 | Thermoplastics pipes Determination of ring stiffness |
| EN 12099:1997 | Plastics piping systems - Polyethylene piping materials and components - Determination of volatile content |
| ISO 9852:2007 | Unplasticized poly(vinyl chloride) (PVC-U) pipes — Dichloromethane resistance at specified temperature (DCMT) — Test method |
| EN ISO 1183-1:2012 | Plastics - Methods for determining the density of non-cellular plastics - Part 1: Immersion method, liquid pyknometer method and titration method (ISO 1183-1:2012) |
| CEN/TS 14541:2013 | Plastics pipes and fittings - Characteristics for utilisation of non-virgin PVC-U, PP and PE materials |
| ISO 1167-1:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method |
| ISO 2505:2005 | Thermoplastics pipes — Longitudinal reversion — Test method and parameters |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.