I.S. EN 13035-2:2008
Current
The latest, up-to-date edition.
MACHINES AND PLANTS FOR THE MANUFACTURE, TREATMENT AND PROCESSING OF FLAT GLASS - SAFETY REQUIREMENTS - PART 2: STORAGE, HANDLING AND TRANSPORTATION EQUIPMENT OUTSIDE THE FACTORY
Hardcopy , PDF
English
01-01-2008
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
3.1 General definitions
3.2 Definitions concerning equipment
4 List of significant hazards
4.1 General
4.2 During transportation
4.3 During loading and unloading
4.4 Flat glass transport by in-loader
5 Safety requirements and/or protective measures
5.1 General
5.2 General requirements
5.3 Angle of lean
5.4 Glass-retaining systems
5.5 Bearers and cladding materials
5.6 Special transport systems
5.6.1 In-loader vehicle
5.6.2 Frail on truck and van
5.6.3 Stillages and pallets
5.7 Vacuum lifting device
6 Verification of safety requirements and/or protective measures
7 Information for use
7.1 General
7.2 Signals and warning devices
7.3 Accompanying documents
7.4 Marking
Annex A (informative) Types of equipment
Annex B (informative) Guidelines for the glass-retention devices
B.1 Hydraulic and pneumatic supports
B.2 Air bags/cushions
B.3 Stanchions for supports on frails
B.4 Protection of the belt against glass impacts by means of
an edge protection
B.5 Straps
Annex C (informative) Symbols for labels and signs
Annex ZA (informative) Relationship between this European Standard
and the Essential Requirements of EU-Directive
98/37/EC
Annex ZB (informative) Relationship between this European Standard
and the Essential Requirements of EU Directive
2006/42/EC
Bibliography
Specifies the requirements for safety for the design and installation of equipment intended for the storage, handling and transportation of flat glass outside the factory and including stillages, pallets, frails fixed to vehicles, in-loader vehicles, specific glass-securing devices, stanchions and vacuum-lifting devices which are used for road transport and on building sites.
| DocumentType |
Standard
|
| Pages |
27
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Current
|
| Standards | Relationship |
| EN 13035-2:2008 | Identical |
| EN 294:1992/AC:1993 | SAFETY OF MACHINERY - SAFETY DISTANCES TO PREVENT DANGER ZONES BEING REACHED BY THE UPPER LIMBS |
| ISO 11202:2010 | Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections |
| EN 1037:1995+A1:2008 | Safety of machinery - Prevention of unexpected start-up |
| ISO 14122-3:2016 | Safety of machinery — Permanent means of access to machinery — Part 3: Stairs, stepladders and guard-rails |
| ISO 14122-1:2016 | Safety of machinery — Permanent means of access to machinery — Part 1: Choice of fixed means and general requirements of access |
| EN 13155:2003+A2:2009 | Cranes - Safety - Non-fixed load lifting attachments |
| EN 13035-3:2003 | Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Part 3: Cutting machines |
| EN 1088:1995+A2:2008 | Safety of machinery - Interlocking devices associated with guards - Principles for design and selection |
| EN 981:1996+A1:2008 | Safety of machinery - System of auditory and visual danger and information signals |
| EN 13035-9:2006+A1:2010 | Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Part 9: Washing installations |
| EN 13035-6:2006+A1:2009 | Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Part 6: Machines for break-out |
| EN 13394:2001 | Packaging - Specification for non-metallic tensional strapping |
| EN 999:1998+A1:2008 | Safety of machinery - The positioning of protective equipment in respect of approach speeds of parts of the human body |
| IEC 60204-1:2016 | Safety of machinery - Electrical equipment of machines - Part 1: General requirements |
| EN ISO 13850:2015 | Safety of machinery - Emergency stop function - Principles for design (ISO 13850:2015) |
| EN 13393:2001 | Packaging - Specification for Edge protectors |
| ISO 14122-4:2016 | Safety of machinery — Permanent means of access to machinery — Part 4: Fixed ladders |
| EN 12195-2:2000 | Load restraint assemblies on road vehicles - Safety - Part 2: Web lashing made from man-made fibres |
| EN ISO 11201:2010 | Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections (ISO 11201:2010) |
| EN ISO 14122-3:2016 | Safety of machinery - Permanent means of access to machinery - Part 3: Stairs, stepladders and guard-rails (ISO 14122-3:2016) |
| EN 953:1997+A1:2009 | Safety of machinery - Guards - General requirements for the design and construction of fixed and movable guards |
| EN 13035-1:2008 | Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Part 1: Storage, handling and transportation equipment inside the factory |
| EN ISO 14122-4:2016 | Safety of machinery - Permanent means of access to machinery - Part 4: Fixed ladders (ISO 14122-4:2016) |
| EN ISO 14122-2:2016 | Safety of machinery - Permanent means of access to machinery - Part 2: Working platforms and walkways (ISO 14122-2:2016) |
| EN 13035-5:2006+A1:2009 | Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Part 5: Machines and installations for stacking and de-stacking |
| ISO 12100-2:2003 | Safety of machinery Basic concepts, general principles for design Part 2: Technical principles |
| ISO 3864-1:2011 | Graphical symbols Safety colours and safety signs Part 1: Design principles for safety signs and safety markings |
| EN 983:1996+A1:2008 | Safety of machinery - Safety requirements for fluid power systems and their components - Pneumatics |
| EN 954-1 : 1996 | SAFETY OF MACHINERY - SAFETY-RELATED PARTS OF CONTROL SYSTEMS - PART 1: GENERAL PRINCIPLES FOR DESIGN |
| ISO 12100-1:2003 | Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology |
| ISO 13850:2015 | Safety of machinery Emergency stop function Principles for design |
| EN 13035-4:2003+A1:2009 | Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Part 4: Tilting tables |
| EN 13246:2001 | Packaging - Specification for tensional steel strapping |
| ISO 14122-2:2016 | Safety of machinery — Permanent means of access to machinery — Part 2: Working platforms and walkways |
| EN 13035-7:2006+A1:2009 | Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Part 7: Cutting machines for laminated glass |
| EN ISO 14122-1:2016 | Safety of machinery - Permanent means of access to machinery - Part 1: Choice of fixed means and general requirements of access (ISO 14122-1:2016) |
| EN ISO 11202:2010 | Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections (ISO 11202:2010) |
| ISO 11201:2010 | Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections |
| EN 13035-11:2006+A1:2010 | Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Part 11: Drilling machines |
| EN 60204-1 : 2006 COR 2010 | SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.