I.S. EN 12897:2016
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
WATER SUPPLY - SPECIFICATION FOR INDIRECTLY HEATED UNVENTED (CLOSED) STORAGE WATER HEATERS
Hardcopy , PDF
02-25-2020
English
01-01-2016
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
National Foreword
European foreword
Introduction
1 Scope
2 Normative references
3 Terms, definitions and symbols
4 Requirements
5 Marking
6 Evaluation of conformity
7 Technical documents
Annex A (normative) - Hot water safety and performance
testing
Annex B (normative) - Measurement of standing heat loss
for factory insulated storage water heaters
Annex C (informative) - Inspection access
Annex ZA (informative) - Relationship between this
European Standard and the requirements of Commission
Delegated Regulation (EU) No 812/2013 of February 2013
supplementing Directive 2010/30/EU regarding energy
labelling for water heaters and hot water storage tanks
Annex ZB (informative) - Relationship between this European
Standard and the requirements of Commission Regulation
(EU) No 814/2013 of 2 August 2013 implementing Directive
2009/125/EC with regard to Ecodesign requirements for
water heaters and hot water storage tanks
Bibliography
Defines the constructional and performance requirements and methods of test for indirectly heated, unvented (closed) storage water heaters of up to 2000 l volume suitable for connection to a water supply at a pressure between 0,05 MPa and 1,0 MPa (0,5 bar and 10 bar), and fitted with control and safety devices designed to prevent the temperature of the stored drinking water from reaching 95 degrees C.
| DocumentType |
Standard
|
| Pages |
38
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| ONORM EN 12897 : 2016 | Identical |
| NBN EN 12897 : 2016 | Identical |
| DIN EN 12897:2006-09 | Identical |
| BS EN 12897:2016 | Identical |
| UNE-EN 12897:2017 | Identical |
| EN 12897:2016 | Identical |
| NEN EN 12897 : 2016 | Identical |
| SN EN 12897 : 2016 | Identical |
| NF EN 12897 : 2016 | Identical |
| NS EN 12897 : 2006 | Identical |
| UNI EN 12897 : 2007 | Identical |
| DIN EN 12897:2016-12 | Identical |
| S.R. 50-2:2012 | BUILDING SERVICES CODE OF PRACTICE - PART 2: THERMAL SOLAR SYSTEMS |
| IEC 60730-2-9:2015 RLV | Automatic electrical controls - Part 2-9: Particular requirements for temperature sensing controls |
| EN 15332:2007 | Heating boilers - Energy assessment of hot water storage systems |
| EN 1490:2000 | Building valves - Combined temperature and pressure relief valves - Tests and requirements |
| EN 60730-2-9:2010 | Automatic electrical controls for household and similar use - Part 2-9: Particular requirements for temperature sensing controls |
| 89/106/EEC : 1988 | COUNCIL DIRECTIVE OF 21 DECEMBER 1988 ON THE APPROXIMATION OF LAWS, REGULATIONS AND ADMINISTRATIVE PROVISIONS OF THE MEMBER STATES RELATING TO CONSTRUCTION PRODUCTS |
| EN 1567:1999 | Building valves - Water pressure reducing valves and combination water pressure reducing valves - Requirements and tests |
| EN 1717:2000 | Protection against pollution of potable water in water installations and general requirements of devices to prevent pollution by backflow |
| IEC 60379:1987 | Methods for measuring the performance of electric storage water-heaters for household purposes |
| EN 1491:2000 | Building valves - Expansion valves - Tests and requirements |
| EN 1488:2000 | Building valves - Expansion groups - Tests and requirements |
| EN 1487:2014 | Building valves - Hydraulic safety groups - Tests and requirements |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| EN 1489:2000 | Building valves - Pressure safety valves - Tests and requirements |
| EN 13959:2004 | Anti-pollution check valves - DN 6 to DN 250 inclusive family E, type A, B, C and D |
| ISO 9001:2015 | Quality management systems — Requirements |
| EN 60379:2004 | Methods for measuring the performance of electric storage water-heaters for household purposes |
| 2009/125/EC : 2009 AMD 1 2012 | DIRECTIVE 2009/125/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 21 OCTOBER 2009 ESTABLISHING A FRAMEWORK FOR THE SETTING OF ECODESIGN REQUIREMENTS FOR ENERGY-RELATED PRODUCTS (RECAST) (TEXT WITH EEA RELEVANCE) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.