I.S. EN 12201-4:2012
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PLASTICS PIPING SYSTEMS FOR WATER SUPPLY, AND FOR DRAINAGE AND SEWERAGE UNDER PRESSURE - POLYETHYLENE (PE) - PART 4: VALVES FOR WATER SUPPLY SYSTEMS
Hardcopy , PDF
02-08-2024
English
01-01-2012
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions, symbols and abbreviations
4 Material
5 General characteristics
6 Geometric characteristics
7 Mechanical characteristics for assembled valves
8 Physical characteristics
9 Performance requirements
10 Marking
11 Delivery Conditions
Annex A (normative) - Determination of the leaktightness
of seat and packing
Bibliography
Defines the characteristics of valves or valve bodies made from polyethylene (PE 100 and PE 80) for buried and above ground applications, intended for the conveyance of water for human consumption, raw water prior to treatment, drainage and sewerage under pressure, vacuum sewer systems, and water for other purposes.
| DevelopmentNote |
Supersedes I.S. EN 13244-4. (02/2012)
|
| DocumentType |
Standard
|
| Pages |
22
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| ONORM EN 12201-4 : 2012 | Identical |
| UNI EN 12201-4 : 2012 | Identical |
| NS EN 12201-4 : 2012 | Identical |
| NBN EN 12201-4 : 2012 | Identical |
| UNE-EN 12201-4:2012 | Identical |
| DIN EN 12201-4:2012-04 | Identical |
| BS EN 12201-4:2012 | Identical |
| NEN EN 12201-4 : 2012 | Identical |
| SN EN 12201-4:2012 | Identical |
| EN 12201-4:2012 | Identical |
| NF EN 12201-4 : 2012 | Identical |
| EN ISO 3126:2005 | Plastics piping systems - Plastics components - Determination of dimensions (ISO 3126:2005) |
| EN 1705:1996 | Plastics piping systems - Thermoplastics valves - Test method for the integrity of a valve after an external blow |
| ISO 5210:2017 | Industrial valves — Multi-turn valve actuator attachments |
| EN ISO 5210:2017 | Industrial valves - Multi-turn valve actuator attachments (ISO 5210:2017) |
| EN 12201-3:2011+A1:2012 | Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 3: Fittings |
| EN 28233:1990 | Thermoplastics valves - Torque - Test method (ISO 8233:1988) |
| EN ISO 1167-1:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 1: General method (ISO 1167-1:2006) |
| ISO 1167-4:2007 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 4: Preparation of assemblies |
| EN 12100:1997 | Plastics piping systems - Polyethylene (PE) valves - Test method for resistance to bending between supports |
| EN 1074-1:2000 | Valves for water supply - Fitness for purpose requirements and appropriate verification tests - Part 1: General requirements |
| EN 736-2:2016 | Valves - Terminology - Part 2: Definition of components of valves |
| CEN/TR 15438:2007 | Plastics piping systems - Guidance for coding of products and their intended uses |
| ISO 3126:2005 | Plastics piping systems Plastics components Determination of dimensions |
| EN ISO 1167-4:2007 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 4: Preparation of assemblies (ISO 1167-4:2007) |
| EN 12201-5:2011 | Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 5: Fitness for purpose of the system |
| EN 1680:1997 | Plastics piping systems - Valves for polyethylene (PE) piping systems - Test method for leaktightness under and after bending applied to the operating mechanisms |
| ISO 10933:1997 | Polyethylene (PE) valves for gas distribution systems |
| EN 12201-2:2011+A1:2013 | Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 2: Pipes |
| ISO 11357-6:2008 | Plastics Differential scanning calorimetry (DSC) Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT) |
| EN ISO 1133:2005 | Plastics - Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics (ISO 1133:2005) |
| EN 12201-1:2011 | Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 1: General |
| ISO 1133:2005 | Plastics Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics |
| CEN/TS 12201-7:2014 | Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 7: Guidance for the assessment of conformity |
| EN 736-3:2008 | Valves - Terminology - Part 3: Definition of terms |
| ISO 1167-1:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.