I.S. EN 12201-1:2011
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PLASTICS PIPING SYSTEMS FOR WATER SUPPLY, AND FOR DRAINAGE AND SEWERAGE UNDER PRESSURE - POLYETHYLENE (PE) - PART 1: GENERAL
Available format(s)
Hardcopy , PDF
Superseded date
02-08-2024
Superseded by
Language(s)
English
Published date
01-01-2011
Publisher
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions, symbols and abbreviations
4 Compound
5 Effect on water quality
Annex A (normative) - Pressure reduction coefficients
Bibliography
Defines the general aspects of polyethylene (PE) pressure piping systems (mains and service pipes) for buried or above ground applications, intended for the conveyance of water for human consumption, raw water prior to treatment, drainage and sewerage under pressure, vacuum sewer systems, and water for other purposes.
| DevelopmentNote |
Supersedes I.S. EN 13244-1. (09/2011) Supersedes I.S. 134 & I.S. 135. (11/2014)
|
| DocumentType |
Standard
|
| Pages |
22
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| ONORM EN 12201-1 : 2015 | Identical |
| BS EN 12201-1:2011 | Identical |
| NBN EN 12201-1 : 2011 | Identical |
| UNI EN 12201-1 : 2012 | Identical |
| NF EN 12201-1 : 2011 | Identical |
| NEN EN 12201-1 : 2011 | Identical |
| DIN EN 12201-1:2011-11 | Identical |
| SN EN 12201-1:2011 | Identical |
| EN 12201-1:2011 | Identical |
| UNE-EN 12201-1:2012 | Identical |
| NS EN 12201-1 : 2011 | Identical |
| EN ISO 12162:2009 | Thermoplastics materials for pipes and fittings for pressure applications - Classification, designation and design coefficient (ISO 12162:2009) |
| ISO 13953:2001 | Polyethylene (PE) pipes and fittings — Determination of the tensile strength and failure mode of test pieces from a butt-fused joint |
| ISO 1167-2:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces |
| EN 12201-3:2011+A1:2012 | Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 3: Fittings |
| 89/106/EEC : 1988 | COUNCIL DIRECTIVE OF 21 DECEMBER 1988 ON THE APPROXIMATION OF LAWS, REGULATIONS AND ADMINISTRATIVE PROVISIONS OF THE MEMBER STATES RELATING TO CONSTRUCTION PRODUCTS |
| EN ISO 16871:2003 | Plastics piping and ducting systems - Plastics pipes and fittings - Method for exposure to direct (natural) weathering (ISO 16871:2003) |
| ISO 6964:1986 | Polyolefin pipes and fittings Determination of carbon black content by calcination and pyrolysis Test method and basic specification |
| EN ISO 1167-2:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 2: Preparation of pipe test pieces (ISO 1167-2:2006) |
| EN ISO 1167-1:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 1: General method (ISO 1167-1:2006) |
| EN ISO 15512:2016 | Plastics - Determination of water content (ISO 15512:2016) |
| ISO 13477:2008 | Thermoplastics pipes for the conveyance of fluids — Determination of resistance to rapid crack propagation (RCP) — Small-scale steady-state test (S4 test) |
| ISO 3:1973 | Preferred numbers Series of preferred numbers |
| EN ISO 13477:2008 | Thermoplastics pipes for the conveyance of fluids - Determination of resistance to rapid crack propagation (RCP) - Small-scale steady-state test (S4 test) (ISO 13477:2008) |
| ISO 18553:2002 | Method for the assessment of the degree of pigment or carbon black dispersion in polyolefin pipes, fittings and compounds |
| ISO 13479:2009 | Polyolefin pipes for the conveyance of fluids Determination of resistance to crack propagation Test method for slow crack growth on notched pipes |
| EN ISO 6259-1:2015 | Thermoplastics pipes - Determination of tensile properties - Part 1: General test method (ISO 6259-1:2015) |
| EN ISO 13478:2007 | Thermoplastics pipes for the conveyance of fluids - Determination of resistance to rapid crack propagation (RCP) - Full-scale test (FST) (ISO 13478:2007) |
| EN ISO 13479:2009 | Polyolefin pipes for the conveyance of fluids - Determination of resistance to crack propagation - Test method for slow crack growth on notched pipes (ISO 13479:2009) |
| ISO 11414:2009 | Plastics pipes and fittings Preparation of polyethylene (PE) pipe/pipe or pipe/fitting test piece assemblies by butt fusion |
| ISO 12162:2009 | Thermoplastics materials for pipes and fittings for pressure applications Classification, designation and design coefficient |
| ISO 6259-1:2015 | Thermoplastics pipes Determination of tensile properties Part 1: General test method |
| ISO 13478:2007 | Thermoplastics pipes for the conveyance of fluids — Determination of resistance to rapid crack propagation (RCP) — Full-scale test (FST) |
| ISO 16871:2003 | Plastics piping and ducting systems — Plastics pipes and fittings — Method for exposure to direct (natural) weathering |
| ISO 472:2013 | Plastics — Vocabulary |
| EN 12201-5:2011 | Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 5: Fitness for purpose of the system |
| ISO 13954:1997 | Plastics pipes and fittings Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm |
| ISO 1183-1:2012 | Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method |
| ISO 1183-2:2004 | Plastics Methods for determining the density of non-cellular plastics Part 2: Density gradient column method |
| EN 12201-2:2011+A1:2013 | Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 2: Pipes |
| ISO 15512:2016 | Plastics Determination of water content |
| ISO 11357-6:2008 | Plastics Differential scanning calorimetry (DSC) Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT) |
| ISO 4065:1996 | Thermoplastics pipes Universal wall thickness table |
| ISO 497:1973 | Guide to the choice of series of preferred numbers and of series containing more rounded values of preferred numbers |
| ISO 13761:2017 | Plastics pipes and fittings — Pressure reduction factors for polyethylene pipeline systems for use at temperatures above 20 degrees C |
| ISO 6259-3:2015 | Thermoplastics pipes Determination of tensile properties Part 3: Polyolefin pipes |
| EN ISO 1133:2005 | Plastics - Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics (ISO 1133:2005) |
| ISO 760:1978 | Determination of water Karl Fischer method (General method) |
| ISO 11413:2008 | Plastics pipes and fittings Preparation of test piece assemblies between a polyethylene (PE) pipe and an electrofusion fitting |
| ISO 1043-1:2011 | Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics |
| ISO 1133:2005 | Plastics Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics |
| EN ISO 472:2013 | Plastics - Vocabulary (ISO 472:2013) |
| EN 12099:1997 | Plastics piping systems - Polyethylene piping materials and components - Determination of volatile content |
| CEN/TS 12201-7:2014 | Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 7: Guidance for the assessment of conformity |
| EN ISO 1183-1:2012 | Plastics - Methods for determining the density of non-cellular plastics - Part 1: Immersion method, liquid pyknometer method and titration method (ISO 1183-1:2012) |
| EN ISO 1183-2:2004 | Plastics - Methods for determining the density of non-cellular plastics - Part 2: Density gradient column method (ISO 1183-2:2004) |
| ISO 1167-1:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.