I.S. EN 12184:2014
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
ELECTRICALLY POWERED WHEELCHAIRS, SCOOTERS AND THEIR CHARGERS - REQUIREMENTS AND TEST METHODS
Hardcopy , PDF
10-07-2024
English
01-01-2014
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Test apparatus
5 Type classes
6 General requirements
7 Preparation for testing
8 Wheelchair performance
9 Component properties
10 Propulsion and braking systems
11 Operations
12 Electrical systems
13 Information supplied by the manufacturer
14 Test report
15 Tables
16 Figures
Annex A (informative) - Recommendations for dimensions
and manoeuvring space of electrically powered
wheelchairs
Annex B (informative) - Recommended design features
Annex C (informative) - Recommendations for lighting
and reflectors
Annex D (informative) - EN 12184 and rail interoperability
Annex E (informative) - Recommendations for safety in
freewheel mode
Annex F (informative) - Wheelchairs with nominal speed
of not less than 10 km/h - Dynamic stability
for slopes of 10 DEGREE or steeper
Annex G (informative) - Technical changes from previous
editions of EN 12184
Annex ZA (informative) - Relationship between this European
Standard and the Essential Requirements of
Council Directive 93/42/EEC
Bibliography
Describes requirements and test methods for electrically powered wheelchairs, including electrically powered scooters with three or more wheels, with a maximum speed not exceeding 15 km/h intended to carry one person of mass not greater than 300 kg.
| DocumentType |
Standard
|
| Pages |
64
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| ONORM EN 12184 : 2014 | Identical |
| NS EN 12184 : 2014 | Identical |
| UNI EN 12184 : 2014 | Identical |
| DIN EN 12184:2014-06 | Identical |
| NBN EN 12184 : 2014 | Identical |
| UNE-EN 12184:2014 | Identical |
| NEN EN 12184 : 2014 | Identical |
| NF EN 12184 : 2014 | Identical |
| EN 12184:2014 | Identical |
| BS EN 12184:2014 | Identical |
| SN EN 12184:2014 | Identical |
| ISO 7176-10:2008 | Wheelchairs — Part 10: Determination of obstacle-climbing ability of electrically powered wheelchairs |
| ISO 7176-2:2017 | Wheelchairs — Part 2: Determination of dynamic stability of electrically powered wheelchairs |
| ISO 8191-2:1988 | Furniture — Assessment of ignitability of upholstered furniture — Part 2: Ignition source: match-flame equivalent |
| IEC 60601-1:2005+AMD1:2012 CSV | Medical electrical equipment - Part 1: General requirements for basic safety and essential performance |
| ISO 7193:1985 | Wheelchairs Maximum overall dimensions |
| ISO 7176-15:1996 | Wheelchairs — Part 15: Requirements for information disclosure, documentation and labelling |
| ISO 7176-1:2014 | Wheelchairs Part 1: Determination of static stability |
| ISO 7176-22:2014 | Wheelchairs — Part 22: Set-up procedures |
| EN 62304:2006/A1:2015 | MEDICAL DEVICE SOFTWARE - SOFTWARE LIFE-CYCLE PROCESSES (IEC 62304:2006/A1:2015) |
| EN 12182:2012 | Assistive products for persons with disability - General requirements and test methods |
| ISO 7176-3:2012 | Wheelchairs — Part 3: Determination of effectiveness of brakes |
| ISO 7176-7:1998 | Wheelchairs — Part 7: Measurement of seating and wheel dimensions |
| IEC 62304:2006+AMD1:2015 CSV | Medical device software - Software life cycle processes |
| ISO 7176-5:2008 | Wheelchairs — Part 5: Determination of dimensions, mass and manoeuvring space |
| ISO 68-1:1998 | ISO general purpose screw threads — Basic profile — Part 1: Metric screw threads |
| ISO 7176-13:1989 | Wheelchairs — Part 13: Determination of coefficient of friction of test surfaces |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| ISO 7176-8:2014 | Wheelchairs Part 8: Requirements and test methods for static, impact and fatigue strengths |
| ISO 7176-21:2009 | Wheelchairs Part 21: Requirements and test methods for electromagnetic compatibility of electrically powered wheelchairs and scooters, and battery chargers |
| ISO 7176-19:2008 | Wheelchairs Part 19: Wheeled mobility devices for use as seats in motor vehicles |
| EN ISO 14971:2012 | Medical devices - Application of risk management to medical devices (ISO 14971:2007, Corrected version 2007-10-01) |
| ISO 7176-11:2012 | Wheelchairs — Part 11: Test dummies |
| EN 60335-1:2012/A13:2017 | HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60335-1:2010, MODIFIED) |
| ISO 14971:2007 | Medical devices Application of risk management to medical devices |
| EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
| EN 1021-2:2014 | Furniture - Assessment of the ignitability of upholstered furniture - Part 2: Ignition source match flame equivalent |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.