I.S. EN 12101-3:2015
Current
The latest, up-to-date edition.
SMOKE AND HEAT CONTROL SYSTEMS - PART 3: SPECIFICATION FOR POWERED SMOKE AND HEAT CONTROL VENTILATORS (FANS)
Hardcopy , PDF
English
01-01-2015
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
National Foreword
European foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions, symbols and abbreviations
4 Requirements
5 Testing, assessment and sampling methods
6 Assessment and verification of constancy of
performance - AVCP
7 Marking, labelling and packaging
Annex A (normative) - Criteria to determine family of fans
in order to select the sizes to be tested
Annex B (normative) - Criteria to determine a family of
motors in order to select the sizes to be tested
Annex C (normative) - Test method for the determination
of fire resistance of powered smoke and heat control
ventilators (fans)
Annex D (normative) - Test methods for electric motors to
determine the impact of the changes on the product
characteristics
Annex E (normative) - Test method for assessing the
response delay and ability to open under environmental
conditions
Annex F (informative) - Explanatory notes
Annex G (informative) - General guidance for installation
and maintenance
Annex ZA (informative) - Clauses of this European Standard
addressing the provisions of the EU Construction
Products Regulation
Bibliography
Defines the products characteristics of powered smoke and heat control ventilators (fans) intended to be used as part of a powered smoke and heat control ventilation system in construction works.
| DevelopmentNote |
2002 COR 2005 Issued on 15/08/2010. (09/2010)
|
| DocumentType |
Standard
|
| Pages |
106
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| SN EN 12101-3:2015 | Identical |
| UNE-EN 12101-3:2016 | Identical |
| NEN EN 12101-3 : 2015 | Identical |
| NBN EN 12101-3 : 2015 | Identical |
| NS EN 12101-3 : 2002 | Identical |
| NF EN 12101-3 : 2015 | Identical |
| UNI EN 12101-3 : 2004 | Identical |
| BS EN 12101-3:2015 | Identical |
| EN 12101-3:2015 | Identical |
| DIN EN 12101-3:2015-12 | Identical |
| ASTM E 228 : 2017 : REDLINE | Standard Test Method for Linear Thermal Expansion of Solid Materials With a Push-Rod Dilatometer |
| EN ISO 6892-1:2016 | Metallic materials - Tensile testing - Part 1: Method of test at room temperature (ISO 6892-1:2016) |
| EN 12101-2:2017 | Smoke and heat control systems - Part 2: Natural smoke and heat exhaust ventilators |
| EN 60085:2008 | Electrical insulation - Thermal evaluation and designation |
| EN 60034-1:2010/corrigendum Oct. 2010 | ROTATING ELECTRICAL MACHINES - PART 1: RATING AND PERFORMANCE |
| ISO 6892-1:2016 | Metallic materials Tensile testing Part 1: Method of test at room temperature |
| EN 13501-4:2016 | Fire classification of construction products and building elements - Part 4: Classification using data from fire resistance tests on components of smoke control systems |
| ISO 3:1973 | Preferred numbers Series of preferred numbers |
| EN ISO 204:2009 | Metallic materials - Uniaxial creep testing in tension - Method of test (ISO 204:2009) |
| ISO 281:2007 | Rolling bearings Dynamic load ratings and rating life |
| EN 60034-18-41:2014 | Rotating electrical machines - Part 18-41: Partial discharge free electrical insulation systems (Type I) used in rotating electrical machines fed from voltage converters - Qualification and quality control tests |
| ASTM E 1461 : 2013 : REDLINE | Standard Test Method for Thermal Diffusivity by the Flash Method |
| EN ISO 5801:2017 | Fans - Performance testing using standardized airways (ISO 5801:2017) |
| ISO 5801:2017 | Fans — Performance testing using standardized airways |
| IEC 60085:2007 | Electrical insulation - Thermal evaluation and designation |
| IEC 60034-2-1:2014 | Rotating electrical machines - Part 2-1: Standard methods for determining losses and efficiency from tests (excluding machines for traction vehicles) |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| IEC TS 60034-17:2006 | Rotating electrical machines - Part 17: Cage induction motors when fed from converters - Application guide |
| IEC 60034-18-41:2014 | Rotating electrical machines - Part 18-41: Partial discharge free electrical insulation systems (Type I) used in rotating electrical machines fed from voltage converters - Qualification and quality control tests |
| EN 60034-2-1:2014 | Rotating electrical machines - Part 2-1: Standard methods for determining losses and efficiency from tests (excluding machines for traction vehicles) |
| IEC 60034-1:2017 | Rotating electrical machines - Part 1: Rating and performance |
| EN ISO 6892-2:2011 | Metallic materials - Tensile testing - Part 2: Method of test at elevated temperature (ISO 6892-2:2011) |
| ISO 9001:2015 | Quality management systems — Requirements |
| ISO 14520-1:2015 | Gaseous fire-extinguishing systems — Physical properties and system design — Part 1: General requirements |
| ISO 6892-2:2011 | Metallic materials Tensile testing Part 2: Method of test at elevated temperature |
| ISO 1099:2017 | Metallic materials — Fatigue testing — Axial force-controlled method |
| CLC/TS 60034-17:2004 | Rotating electrical machines - Part 17: Cage induction motors when fed from converters - Application guide |
| ISO 834-1:1999 | Fire-resistance tests Elements of building construction Part 1: General requirements |
| ISO 204:2009 | Metallic materials Uniaxial creep testing in tension Method of test |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.