I.S. EN 12079-1:2006
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
OFFSHORE CONTAINERS AND ASSOCIATED LIFTING SETS - PART 1: OFFSHORE CONTAINERS - DESIGN, MANUFACTURE AND MARKING
Hardcopy , PDF
07-23-2013
English
01-01-2006
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols
5 Design
5.1 General
5.2 Structural strength
5.3 Welding
5.4 Additional design details
5.5 Tank containers
5.6 Containers for bulk solids
6 Materials
6.1 Steel - General
6.2 Rolled and extruded steels in offshore container
structures
6.3 Aluminium
6.4 Non-metallic materials
6.5 Material certificates
7 Type testing
7.1 General
7.2 Test equipment and calibration
7.3 Lifting test
7.4 Vertical impact test
7.5 Other tests
8 Production
8.1 General
8.2 Primary structure
8.3 Secondary structure
8.4 Production testing
8.5 Failure of production containers
9 Marking
9.1 Safety marking
9.2 Identification markings
9.3 Information markings
9.4 Other markings
10 Container Data Plate
10.1 General
10.2 Contents of Data Plate
11 Certificate of conformity
11.1 General
11.2 Documentation
11.3 Contents of the certificate of conformity
Annex A (Informative) Certification Requirements for
Containers
Bibliography
States requirements for the design, manufacture and marking of offshore freight and service containers with maximum gross mass not exceeding 25000 kg, intended for repeated use to, from and between offshore installations and ships.
| DevelopmentNote |
Together with I.S. EN 12079-3 supersedes I.S. EN 12079. (07/2006)
|
| DocumentType |
Standard
|
| Pages |
36
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| UNE-EN 12079-1:2007 | Identical |
| NF EN 12079-1 : 2006 | Identical |
| UNI EN 12079-1 : 2006 | Identical |
| NBN EN 12079-1 : 2006 | Identical |
| SN EN 12079-1 : 2006 | Identical |
| EN 12079-1:2006 | Identical |
| DIN EN 12079-1:2006-07 | Identical |
| BS EN 12079-1:2006 | Identical |
| NS EN 12079-1 : 1ED 2006 | Identical |
| NEN EN 12079-1 : 2006 | Identical |
| EN 10002-1 : 2001 | METALLIC MATERIALS - TENSILE TESTING - PART 1: METHOD OF TEST AT AMBIENT TEMPERATURE |
| EN ISO 5817:2014 | Welding - Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) - Quality levels for imperfections (ISO 5817:2014) |
| ISO 209-1:1989 | Wrought aluminium and aluminium alloys Chemical composition and forms of products Part 1: Chemical composition |
| ISO 9606-2:2004 | Qualification test of welders — Fusion welding — Part 2: Aluminium and aluminium alloys |
| EN 10025-4:2004 | Hot rolled products of structural steels - Part 4: Technical delivery conditions for thermomechanical rolled weldable fine grain structural steels |
| ISO 1496-1:2013 | Series 1 freight containers — Specification and testing — Part 1: General cargo containers for general purposes |
| EN 30042 : 1994 | ARC WELDED JOINTS IN ALUMINIUM AND ITS WELDABLE ALLOYS - GUIDANCE ON QUALITY LEVELS FOR IMPERFECTIONS |
| ISO 10042:2005 | Welding Arc-welded joints in aluminium and its alloys Quality levels for imperfections |
| ISO 15614-2:2005 | Specification and qualification of welding procedures for metallic materials Welding procedure test Part 2: Arc welding of aluminium and its alloys |
| EN 10164:2004 | Steel products with improved deformation properties perpendicular to the surface of the product - Technical delivery conditions |
| EN 1011-1:2009 | Welding - Recommendations for welding of metallic materials - Part 1: General guidance for arc welding |
| EN 10025-1:2004 | Hot rolled products of structural steels - Part 1: General technical delivery conditions |
| EN 473:2008 | Non-destructive testing - Qualification and certification of NDT personnel - General principles |
| EN 10210-1:2006 | Hot finished structural hollow sections of non-alloy and fine grain steels - Part 1: Technical delivery conditions |
| EN 10045-1 : 1990 | METALLIC MATERIALS - CHARPY IMPACT TEST - PART 1: TEST METHOD |
| ISO 5817:2014 | Welding — Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) — Quality levels for imperfections |
| EN 12079-3:2006 | Offshore containers and associated lifting sets - Part 3: Periodic inspection, examination and testing |
| ISO 15614-1:2017 | Specification and qualification of welding procedures for metallic materials — Welding procedure test — Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys |
| ISO 15609-1:2004 | Specification and qualification of welding procedures for metallic materials Welding procedure specification Part 1: Arc welding |
| EN 10219-1:2006 | Cold formed welded structural hollow sections of non-alloy and fine grain steels - Part 1: Technical delivery conditions |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| EN 1289:1998/A2:2003 | NON-DESTRUCTIVE TESTING OF WELDS - PENETRANT TESTING OF WELDS - ACCEPTANCE LEVELS |
| EN ISO 15614-2:2005 | Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 2: Arc welding of aluminium and its alloys (ISO 15614-2:2005) |
| ISO 1496-3:1995 | Series 1 freight containers Specification and testing Part 3: Tank containers for liquids, gases and pressurized dry bulk |
| EN ISO 9606-2:2004 | Qualification test of welders - Fusion welding - Part 2: Aluminium and aluminium alloys (ISO 9606-2:2004) |
| EN 10250-2:1999 | Open die steel forgings for general engineering purposes - Part 2: Non-alloy quality and special steels |
| ISO 668:2013 | Series 1 freight containers Classification, dimensions and ratings |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| ISO 9001:2015 | Quality management systems — Requirements |
| EN ISO 15609-1:2004 | Specification and qualification of welding procedures for metallic materials - Welding procedure specification - Part 1: Arc welding (ISO 15609-1:2004) |
| ISO 1496-4:1991 | Series 1 freight containers — Specification and testing — Part 4: Non-pressurized containers for dry bulk |
| EN 1712:1997/A2:2004 | NON-DESTRUCTIVE TESTING OF WELDS - ULTRASONIC TESTING OF WELDED JOINTS - ACCEPTANCE LEVELS |
| EN 12079-2:2006 | Offshore containers and associated lifting sets - Part 2: Lifting sets - Design, manufacture and marking |
| ISO 7500-1:2015 | Metallic materials Calibration and verification of static uniaxial testing machines Part 1: Tension/compression testing machines Calibration and verification of the force-measuring system |
| EN 12517-1:2006 | Non-destructive testing of welds - Part 1: Evaluation of welded joints in steel, nickel, titanium and their alloys by radiography - Acceptance levels |
| EN 1291:1998/A2:2003 | NON-DESTRUCTIVE TESTING OF WELDS - MAGNETIC PARTICLE TESTING OF WELDS - ACCEPTANCE LEVELS |
| ISO 15607:2003 | Specification and qualification of welding procedures for metallic materials General rules |
| EN 571-1:1997 | Non destructive testing - Penetrant testing - Part 1: General principles |
| EN 970:1997 | Non-destructive examination of fusion welds - Visual examination |
| EN 1290:1998/A2:2003 | NON-DESTRUCTIVE EXAMINATION OF WELDS - MAGNETIC PARTICLE EXAMINATION OF WELDS |
| EN 10025-3:2004 | Hot rolled products of structural steels - Part 3: Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steels |
| EN 10250-3:1999 | Open die steel forgings for general engineering purposes - Part 3: Alloy special steels |
| EN ISO 15607:2003 | Specification and qualification of welding procedures for metallic materials - General rules (ISO 15607:2003) |
| 1994/9/EC : 1994 | DIRECTIVE 94/9/EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL OF 23 MARCH 1994 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES CONCERNING EQUIPMENT AND PROTECTIVE SYSTEMS INTENDED FOR USE IN POTENTIALLY EXPLOSIVE ATMOSPHERES |
| ISO 1161:2016 | Series 1 freight containers — Corner and intermediate fittings — Specifications |
| EN 287-1:2011 | Qualification test of welders - Fusion welding - Part 1: Steels |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.