I.S. EN 1071-3:2005
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
ADVANCED TECHNICAL CERAMICS - METHODS OF TEST FOR CERAMIC COATINGS - PART 3: DETERMINATION OF ADHESION AND OTHER MECHANICAL FAILURE MODES BY A SCRATCH TEST
Hardcopy , PDF
05-08-2016
English
01-01-2005
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Principle
4 Apparatus and materials
4.1 Scratch tester
4.2 Diamond stylus
5 Preparation of the test piece
5.1 General requirements
5.2 Surface roughness, waviness and levelling
5.3 Specimen cleaning
5.4 Coating-substrate specific parameters
6 Test procedure
6.1 General
6.2 Equipment preparation
6.3 Environmental conditions
6.4 Scratching procedure
6.5 Scratch evaluation and critical load
determination
6.6 Microscope observation
6.7 Acoustic emission (AE) and frictional force
(FF) recording
7 Repeatability and limits
8 Test report
Annex A (normative) Procedure for calibration of a
scratch testing system
A.1 Introduction
A.2 Scope
A.3 Principle
A.4 Apparatus
A.5 Calibration procedures
A.6 Recording results
Annex B (informative) Typical failure modes obtained
in scratch testing
B.1 Introduction
B.2 Experimental
B.3 Results
B.4 Conclusions
B.5 The scratch test atlas of failure
modes
Bibliography
Defines a method of testing ceramic coatings by scratching with a loaded diamond stylus so as to promote adhesive and/or cohesive failure of the coating-substrate system.
| DevelopmentNote |
Supersedes I.S. ENV 1071-3. (11/2005)
|
| DocumentType |
Standard
|
| Pages |
49
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| UNI EN 1071-3 : 2005 | Identical |
| NF EN 1071-3 : 2005 | Identical |
| NS EN 1071-3 : 1ED 2005 | Identical |
| NBN EN 1071-3 : 2005 | Identical |
| EN 1071-3:2005 | Identical |
| SN EN 1071-3 : 2005 | Identical |
| BS EN 1071-3:2005 | Identical |
| NEN EN 1071-3 : 2005 | Identical |
| DIN EN 1071-3:2005-10 | Identical |
| ISO/IEC 17025:2005 | General requirements for the competence of testing and calibration laboratories |
| ISO 4287:1997 | Geometrical Product Specifications (GPS) — Surface texture: Profile method — Terms, definitions and surface texture parameters |
| ISO 6508-2:2015 | Metallic materials — Rockwell hardness test — Part 2: Verification and calibration of testing machines and indenters |
| EN ISO 6508-2:2015 | Metallic materials - Rockwell hardness test - Part 2: Verification and calibration of testing machines and indenters (ISO 6508-2:2015) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.