I.S. EN 1011-8:2004
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
WELDING - RECOMMENDATIONS FOR WELDING OF METALLIC MATERIALS - PART 8: WELDING OF CAST IRONS
Hardcopy , PDF
06-10-2020
English
01-01-2004
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
National foreword
European foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Abbreviations and symbols
5 Provision for quality assurance requirements
6 Storage, handling and identification of parent metal
7 Fusion welding processes
8 Welding consumables
9 Equipment
10 Fabrication
11 Weld preparation
12 Fabrication and inspection feasibility
13 Pre-heat temperature and interpass temperature
14 Tack welds
15 Temporary attachments
16 Run-on plates and run-off plates
17 Arc strikes
18 Weld run sequence
19 Heat input
20 Welding procedure specification (WPS)
21 Traceability
22 Elimination of distortion or inherent stresses
23 Inspection and testing
24 Quality requirements
25 Non-conformance and corrective actions
26 Distortion
27 Post weld heat treatment
28 Surface cleaning and treatment
Annex A (normative) - Quality requirements
Annex B (informative) - Welding technology for cast
iron castings
Bibliography
Provides the requirements for fusion welding of unalloyed and low-alloy cast iron castings produced in accordance with: - EN 1561, Founding - Grey cast irons; - EN 1562, Founding - Malleable cast irons; - EN 1563, Founding - Spheroidal graphite cast irons.
| DocumentType |
Standard
|
| Pages |
22
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| UNI EN 1011-8 : 2006 | Identical |
| DIN EN 1011-8:2016-03 (Draft) | Identical |
| NF EN 1011-8 : 2005 | Identical |
| SN EN 1011-8 : 2005 | Identical |
| NS EN 1011-8 : 1ED 2004 | Identical |
| UNE-EN 1011-8:2005 | Identical |
| ONORM EN 1011-8 : 2005 | Identical |
| NBN EN 1011-8 : 2005 | Identical |
| BS EN 1011-8:2004 | Identical |
| EN 1011-8:2018 | Identical |
| ISO 3834-1:2005 | Quality requirements for fusion welding of metallic materials Part 1: Criteria for the selection of the appropriate level of quality requirements |
| ISO 14341:2010 | Welding consumables Wire electrodes and weld deposits for gas shielded metal arc welding of non alloy and fine grain steels Classification |
| ISO 2560:2009 | Welding consumables Covered electrodes for manual metal arc welding of non-alloy and fine grain steels Classification |
| EN 1011-1:2009 | Welding - Recommendations for welding of metallic materials - Part 1: General guidance for arc welding |
| EN 1562:2012 | Founding - Malleable cast irons |
| EN ISO 4063:2010 | Welding and allied processes - Nomenclature of processes and reference numbers (ISO 4063:2009, Corrected version 2010-03-01) |
| EN 12536:2000 | Welding consumables - Rods for gas welding of non alloy and creep-resisting steels - Classification |
| ISO 15609-1:2004 | Specification and qualification of welding procedures for metallic materials Welding procedure specification Part 1: Arc welding |
| EN ISO 14341:2011 | Welding consumables - Wire electrodes and weld deposits for gas shielded metal arc welding of non alloy and fine grain steels - Classification (ISO 14341:2010) |
| EN ISO 2560:2009 | Welding consumables - Covered electrodes for manual metal arc welding of non-alloy and fine grain steels - Classification (ISO 2560:2009) |
| ISO 17632:2015 | Welding consumables Tubular cored electrodes for gas shielded and non-gas shielded metal arc welding of non-alloy and fine grain steels Classification |
| EN ISO 17632:2015 | Welding consumables - Tubular cored electrodes for gas shielded and non-gas shielded metal arc welding of non-alloy and fine grain steels - Classification (ISO 17632:2015) |
| EN 1563:2011 | Founding - Spheroidal graphite cast irons |
| EN ISO 15609-1:2004 | Specification and qualification of welding procedures for metallic materials - Welding procedure specification - Part 1: Arc welding (ISO 15609-1:2004) |
| EN ISO 1071:2015 | Welding consumables - Covered electrodes, wires, rods and tubular cored electrodes for fusion welding of cast iron - Classification (ISO 1071:2015) |
| EN ISO 3834-1:2005 | Quality requirements for fusion welding of metallic materials - Part 1: Criteria for the selection of the appropriate level of quality requirements (ISO 3834-1:2005) |
| ISO 15609-2:2001 | Specification and qualification of welding procedures for metallic materials Welding procedure specification Part 2: Gas welding |
| ISO 9692-2:1998 | Welding and allied processes — Joint preparation — Part 2: Submerged arc welding of steels |
| ISO 1071:2015 | Welding consumables Covered electrodes, wires, rods and tubular cored electrodes for fusion welding of cast iron Classification |
| EN ISO 636:2017 | Welding consumables - Rods, wires and deposits for tungsten inert gas welding of non-alloy and fine-grain steels - Classification (ISO 636:2017) |
| ISO 636:2017 | Welding consumables — Rods, wires and deposits for tungsten inert gas welding of non-alloy and fine-grain steels — Classification |
| EN 1561:2011 | Founding - Grey cast irons |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.