GEIA TA HB 0009 : 2013
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
RELIABILITY PROGRAM HANDBOOK
Available format(s)
Hardcopy , PDF
Superseded date
06-21-2022
Superseded by
Language(s)
English
Published date
01-01-2013
Important note : All end users must be registered with an Account prior to user licenses being assigned.
1. Introduction
2. Activities
3. METHODS
Annex A - List of References (Informative)
Annex B - Symbols and Abbreviated Terms (Informative)
Specifies 'how to' guidance to industry and government for the reliability Activities and Methods contained in ANSI/GEIA-STD-0009 for developing reliable products and systems, successfully demonstrating them during test and evaluation, and sustaining them throughout the system/product life cycle.
| Committee |
G-41
|
| DevelopmentNote |
Supersedes GEIA HB 0009. (04/2013)
|
| DocumentType |
Standard
|
| Pages |
475
|
| PublisherName |
Government Electronics & Information Technology Association
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| IEC 61025:2006 | Fault tree analysis (FTA) |
| MIL-STD-2119 Revision A:1990 | DESIGN REQUIREMENTS FOR PRINTED WIRING ELECTRICAL BACKPLANE ASSEMBLIES |
| IPC 6011 : 0 | GENERIC PERFORMANCE SPECIFICATION FOR PRINTED BOARDS |
| MIL-HDBK-965 Base Document:1996 | ACQUISITION PRACTICES FOR PARTS MANAGEMENT |
| MIL-STD-1530 Revision D:2016 | AIRCRAFT STRUCTURAL INTEGRITY PROGRAM (ASIP) |
| SAE ARP 5580 : 2012 | RECOMMENDED FAILURE MODES AND EFFECTS ANALYSIS (FMEA) PRACTICES FOR NON-AUTOMOBILE APPLICATIONS |
| ISO 2859-3:2005 | Sampling procedures for inspection by attributes — Part 3: Skip-lot sampling procedures |
| QML 31032 : 20171107 | QUALIFIED PRODUCT LIST OF PRODUCTS QUALIFIED UNDER PERFORMANCE SPECIFICATION - MIL-PRF-31032 - PRINTED CIRCUIT BOARD/PRINTED WIRING BOARD, GENERAL SPECIFICATION FOR |
| SAE JA 1012 : 2011 | A GUIDE TO THE RELIABILITY-CENTERED MAINTENANCE (RCM) STANDARD |
| MIL-STD-883 Revision K:2016 | TEST METHOD STANDARD - MICROCIRCUITS |
| SAE JA1011_200908 | EVALUATION CRITERIA FOR RELIABILITY-CENTERED MAINTENANCE (RCM) PROCESSES |
| IEC 60812:2006 | Analysis techniques for system reliability - Procedure for failure mode and effects analysis (FMEA) |
| DEFSTAN 00-42(PT1)/2(2008) : 2008 | RELIABILITY AND MAINTAINABILITY (R&M) ASSURANCE ACTIVITY - PART 1: ONE-SHOT DEVICES/SYSTEMS |
| MIL-STD-810 Revision G:2008 | ENVIRONMENTAL ENGINEERING CONSIDERATIONS AND LABORATORY TESTS |
| IEC 62628:2012 | Guidance on software aspects of dependability |
| IEC 61014:2003 | Programmes for reliability growth |
| MIL-STD-975 Revision M:1994 | NASA STANDARD (EEE) PARTS LIST |
| GEIA TB 0003 : 2009 | COUNTERFEIT PARTS & MATERIALS RISK MITIGATION |
| MIL-HDBK-83578 Base Document:1999 | CRITERIA FOR EXPLOSIVE SYSTEMS AND DEVICES USED ON SPACE VEHICLES |
| AIAG FMEA 3 : 2001 | POTENTIAL FAILURE MODE AND EFFECTS ANALYSIS (FMEA) |
| IEC 61165:2006 | Application of Markov techniques |
| MIL-HDBK-2173 Base Document:1998 | RELIABILITY-CENTERED MAINTENANCE REQUIREMENTS FOR NAVAL AIRCRAFT, WEAPONS SYSTEMS & SUPPORT EQUIPMENT |
| MIL-HDBK-781 Revision A:1996 | RELIABILITY TEST METHODS, PLANS, AND ENVIRONMENTS FOR ENGINEERING DEVELOPMENT, QUALIFICATION AND PRODUCTION |
| MIL-STD-750 Revision F:2011 | TEST METHODS FOR SEMICONDUCTOR DEVICES |
| MIL-STD-1916 Base Document:1996 | DOD PREFERRED METHODS FOR ACCEPTANCE OF PRODUCT |
| ISO 2859-2:1985 | Sampling procedures for inspection by attributes — Part 2: Sampling plans indexed by limiting quality (LQ) for isolated lot inspection |
| SAE ARP 1332 : 2013 | WAVE SOLDERING PROCEDURE |
| ISO 2859-0:1995 | Sampling procedures for inspection by attributes — Part 0: Introduction to the ISO 2859 attribute sampling system |
| ARMP-8 : 1991 | RELIABILITY & MAINTAINABILITY (R&M) IN THE PROCUREMENT OF OFF-THE-SHELF (OTS) EQUIPMENT |
| MIL STD 1843 : 0 | RELIABILITY-CENTERED MAINTENANCE FOR AIRCRAFT, ENGINES AND EQUIPMENT |
| SAE AS 9100D : 2016 | QUALITY MANAGEMENT SYSTEMS - REQUIREMENTS FOR AVIATION, SPACE AND DEFENSE ORGANIZATIONS |
| MIL-STD-414 Base Document:1957 | SAMPLING PROCEDURE AND TABLE FOR INSPECTION BY VARIABLES FOR PERCENT DEFECTIVE |
| AIAA R 013 : 1992 | RECOMMENDED PRACTICE FOR SOFTWARE RELIABILITY |
| MIL-HDBK-338 Revision B:1998 | ELECTRONIC RELIABILITY DESIGN HANDBOOK |
| MIL-STD-965 Revision B:1993 | PARTS CONTROL PROGRAM |
| ISO 8422:2006 | Sequential sampling plans for inspection by attributes |
| DEFSTAN 00-42(PT3)/4(2011) : 2011 | RELIABILITY AND MAINTAINABILITY ASSURANCE GUIDE - PART 3: R&M CASE |
| MIL-HDBK-472 Base Document:1966 | MAINTAINABILITY PREDICTION |
| SAE J 1739 : 2009 | POTENTIAL FAILURE MODE AND EFFECTS ANALYSIS IN DESIGN (DESIGN FMEA), POTENTIAL FAILURE MODE AND EFFECTS ANALYSIS IN MANUFACTURING AND ASSEMBLY PROCESSES (PROCESS FMEA) |
| MIL-STD-2000 Revision A:1991 | STANDARD REQUIREMENTS FOR SOLDERED ELECTRICAL AND ELECTRONIC ASSEMBLIES |
| ISO/TR 8550:1994 | Guide for the selection of an acceptance sampling system, scheme or plan for inspection of discrete items in lots |
| MIL-STD-882 Revision E:2012 | System Safety |
| MIL-HDBK-2165 Base Document:1995 | Testability Program for Systems and Equipments |
| MIL-HDBK-108 Base Document:1960 | QUALITY CONTROL AND RELIABILITY SAMPLING PROCEDURES AND TABLES FOR LIFE AND RELIABILITY TESTING (BASED ON EXPONENTIAL DISTRIBUTION) |
| IEC 60300-3-11:2009 | Dependability management - Part 3-11: Application guide - Reliability centred maintenance |
| MIL-STD-1472 Revision G:2012 | HUMAN ENGINEERING |
| MIL H 38534 : B (1) | HYBRID MICROCIRCUITS, GENERAL SPECIFICATION FOR |
| IEEE 1633-2016 REDLINE | IEEE Recommended Practice on Software Reliability |
| MIL-HDBK-310 Base Document:1997 | DEPARTMENT OF DEFENSE HANDBOOK - GLOBAL CLIMATIC DATA FOR DEVELOPING MILITARY PRODUCTS |
| GEIA STD 0009 : 2008 | RELIABILITY PROGRAM STANDARD FOR SYSTEMS DESIGN, DEVELOPMENT AND MANUFACTURING |
| AIAG QS 9000 : 3ED 98 | QUALITY SYSTEM REQUIREMENTS |
| MIL-HDBK-470 Revision A:1997 | Designing and Developing Maintainable Products and Systems, Volume I |
| MIL-STD-3018 Base Document:2007 | Parts Management (S/S by MIL-STD-11991) |
| MIL-STD-1629 Revision A:1980 | PROCEDURES FOR PERFORMING A FAILURE MODE, EFFECTS AND CRITICALITY ANALYSIS |
| MIL-HDBK-189 Revision C:2011 | RELIABILITY GROWTH MANAGEMENT |
| MIL-STD-690 Revision D:2005 | Failure Rate (FR) Sampling Plans and Procedures |
| MIL-STD-105 Revision E:1989 | SAMPLING PROCEDURES AND TABLES FOR INSPECTION BY ATTRIBUTES |
| SAE ARP 1612 : 2014 | POLYIMIDE PRINTED CIRCUIT BOARDS, FABRICATION OF |
| MIL-HDBK-727 Base Document:1984 | DESIGN GUIDANCE FOR PRODUCIBILITY |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.