EN ISO 6892-2:2011
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Metallic materials - Tensile testing - Part 2: Method of test at elevated temperature (ISO 6892-2:2011)
Superseded date
07-29-2019
Superseded by
Published date
02-15-2011
Publisher
Sorry this product is not available in your region.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and designations
5 Principle
6 Test piece
7 Determination of original cross-sectional area (S[o])
8 Marking the original gauge length (L[o])
9 Apparatus
10 Test conditions
11 Determination or calculation of the properties
12 Test report
13 Measurement uncertainty
14 Figures
15 Annexes
Annex A (informative) - Addition to Annexes B and D
of ISO 6892-1:2009
Annex B (informative) - Measurement uncertainty
Bibliography
ISO 6892-2:2011 specifies a method of tensile testing of metallic materials at temperatures higher than room temperature.
| Committee |
CEN/TC 459/SC 1
|
| DevelopmentNote |
Supersedes EN 10002-5. (03/2011)
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| NBN EN ISO 6892-2 : 2011 | Identical |
| NF EN ISO 6892-2 : 2011 | Identical |
| NS EN ISO 6892-2 : 2011 | Identical |
| UNI EN ISO 6892-2:2018 | Identical |
| SN EN ISO 6892-2 : 2011 | Identical |
| I.S. EN ISO 6892-2:2018 | Identical |
| BS EN ISO 6892-2:2011 | Identical |
| UNI EN ISO 6892-2 : 2011 | Identical |
| UNE-EN ISO 6892-2:2018 | Identical |
| DIN EN ISO 6892-2:2011-05 | Identical |
| BS EN ISO 6892-2:2018 | Identical |
| PN EN ISO 6892-2:2018 | Identical |
| ÖNORM EN ISO 6892-2:2018 | Identical |
| ONORM EN ISO 6892-2 : 2011 | Identical |
| NS EN ISO 6892-2 : 2018 | Identical |
| NEN EN ISO 6892-2 : 2011 | Identical |
| PN EN ISO 6892-2 : 2011 | Identical |
| I.S. EN ISO 6892-2:2011 | Identical |
| UNE-EN ISO 6892-2:2011 | Identical |
| ISO 6892-2:2011 | Identical |
| ISO 6892-2:2018 | Identical |
| DIN EN ISO 6892-2:2018-09 | Identical |
| PREN 10253-2 : DRAFT 2017 | BUTT-WELDING PIPE FITTINGS - PART 2: NON ALLOY AND FERRITIC ALLOY STEELS WITH SPECIFIC INSPECTION REQUIREMENTS |
| 13/30290101 DC : 0 | BS EN 4700-2 - AEROSPACE SERIES - STEEL AND HEAT RESISTING ALLOYS - WROUGHT PRODUCTS - TECHNICAL SPECIFICATION - PART 002: BAR AND SECTION |
| BS EN 15566:2016 | Railway applications. Railway rolling stock. Draw gear and screw coupling |
| PREN 10207 : DRAFT 2015 | STEELS FOR SIMPLE PRESSURE VESSELS - TECHNICAL DELIVERY REQUIREMENTS FOR PLATES, STRIPS AND BARS |
| PREN 10028-1 : DRAFT 2014 | FLAT PRODUCTS MADE OF STEELS FOR PRESSURE PURPOSES - PART 1: GENERAL REQUIREMENTS |
| NF EN 4700-007 : 2012 | AEROSPACE SERIES - STEEL AND HEAT RESISTING ALLOYS - WROUGHT PRODUCTS - TECHNICAL SPECIFICATION - PART 007: REMELTING STOCK |
| I.S. EN 10216-2:2013 | SEAMLESS STEEL TUBES FOR PRESSURE PURPOSES - TECHNICAL DELIVERY CONDITIONS - PART 2: NON-ALLOY AND ALLOY STEEL TUBES WITH SPECIFIED ELEVATED TEMPERATURE PROPERTIES |
| BS EN 13480-8:2017+A1:2019 | Metallic industrial piping Additional requirements for aluminium and aluminium alloy piping |
| EN 10222-1:2017 | Steel forgings for pressure purposes - Part 1: General requirements for open die forgings |
| BS EN 13480-8:2017 | Metallic industrial piping Additional requirements for aluminium and aluminium alloy piping |
| BS EN 10216-2:2013 | Seamless steel tubes for pressure purposes. Technical delivery conditions Non-alloy and alloy steel tubes with specified elevated temperature properties |
| BS EN 12101-3:2015 | Smoke and heat control systems Specification for powered smoke and heat control ventilators (Fans) |
| UNE-EN 10272:2016 | Stainless steel bars for pressure purposes |
| BS EN 10272:2007 | Stainless steel bars for pressure purposes |
| UNE-EN 10314:2016 | Method for the derivation of minimum values of proof strength of steel at elevated temperatures |
| I.S. EN 10222-1:2017 | STEEL FORGINGS FOR PRESSURE PURPOSES - PART 1: GENERAL REQUIREMENTS FOR OPEN DIE FORGINGS |
| I.S. EN 10218-1:2012 | STEEL WIRE AND WIRE PRODUCTS - GENERAL - PART 1: TEST METHODS |
| EN 12101-3:2015 | Smoke and heat control systems - Part 3: Specification for powered smoke and heat control ventilators (Fans) |
| EN 12952-2:2011 | Water-tube boilers and auxiliary installations - Part 2: Materials for pressure parts of boilers and accessories |
| EN 10088-2:2014 | Stainless steels - Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes |
| EN 10314:2016 | Method for the derivation of minimum values of proof strength of steel at elevated temperatures |
| EN 10273:2016 | Hot rolled weldable steel bars for pressure purposes with specified elevated temperature properties |
| EN 10088-3:2014 | Stainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes |
| DIN EN 10218-1:2012-03 | STEEL WIRE AND WIRE PRODUCTS - GENERAL - PART 1: TEST METHODS |
| EN 10272:2016 | Stainless steel bars for pressure purposes |
| EN 10269:2013 | Steels and nickel alloys for fasteners with specified elevated and/or low temperature properties |
| EN 10207:2017 | Steels for simple pressure vessels - Technical delivery requirements for plates, strips and bars |
| EN 10218-1:2012 | Steel wire and wire products - General - Part 1: Test methods |
| EN 10028-1:2017 | Flat products made of steels for pressure purposes - Part 1: General requirements |
| 12/30270633 DC : 0 | BS EN 10222-1 - STEEL FORGINGS FOR PRESSURE PURPOSES - PART 1: GENERAL REQUIREMENTS |
| 11/30253751 DC : 0 | BS EN 10269 - STEELS AND NICKEL ALLOYS FOR FASTENERS WITH SPECIFIED ELEVATED AND/OR LOW TEMPERATURE PROPERTIES |
| EN 4700-002:2016 | Aerospace series - Steel and heat resisting alloys - Wrought products - Technical specification - Part 002: Bar and section |
| UNI EN 10217-7 : 2014 | WELDED STEEL TUBES FOR PRESSURE PURPOSES - TECHNICAL DELIVERY CONDITIONS - PART 7: STAINLESS STEEL TUBES |
| PREN 10088-2 : DRAFT 2011 | STAINLESS STEELS - PART 2: TECHNICAL DELIVERY CONDITIONS FOR SHEET/PLATE AND STRIP OF CORROSION RESISTING STEELS FOR GENERAL PURPOSES |
| NF EN 4700-005 : 2012 | AEROSPACE SERIES - STEEL AND HEAT RESISTING ALLOYS - WROUGHT PRODUCTS - TECHNICAL SPECIFICATION - PART 005: FORGING STOCK |
| UNE-EN 13480-8:2017 | Metallic industrial piping - Part 8: Additional requirements for aluminium and aluminium alloy piping |
| NF EN 4800-003 : 2012 | AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 003: TUBE |
| PREN 764-4 : DRAFT 2012 | PRESSURE EQUIPMENT - PART 4: ESTABLISHMENT OF TECHNICAL DELIVERY CONDITIONS FOR METALLIC MATERIALS |
| PREN 10272 : DRAFT 2013 | STAINLESS STEEL BARS FOR PRESSURE PURPOSES |
| NF EN 4800-006 : 2012 | AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 006: PRE-PRODUCTION AND PRODUCTION FORGINGS |
| NF EN 4800-002 : 2012 | AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 002: BAR AND SECTION |
| NF EN 4700-002 : 2012 | AEROSPACE SERIES - STEEL AND HEAT RESISTING ALLOYS - WROUGHT PRODUCTS - TECHNICAL SPECIFICATION - PART 002: BAR AND SECTION |
| DIN EN 10216-5:2014-03 | Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 5: Stainless steel tubes |
| DIN EN 12101-3:2015-12 | SMOKE AND HEAT CONTROL SYSTEMS - PART 3: SPECIFICATION FOR POWERED SMOKE AND HEAT CONTROL VENTILATORS (FANS) |
| DIN EN 10269:2014-02 | STEELS AND NICKEL ALLOYS FOR FASTENERS WITH SPECIFIED ELEVATED AND/OR LOW TEMPERATURE PROPERTIES |
| DIN EN 10216-2:2014-03 | SEAMLESS STEEL TUBES FOR PRESSURE PURPOSES - TECHNICAL DELIVERY CONDITIONS - PART 2: NON-ALLOY AND ALLOY STEEL TUBES WITH SPECIFIED ELEVATED TEMPERATURE PROPERTIES |
| UNE-EN 12101-3:2016 | Smoke and heat control systems - Part 3: Specification for powered smoke and heat control ventilators (Fans) |
| DIN EN 1559-2:2014-12 | FOUNDING - TECHNICAL CONDITIONS OF DELIVERY - PART 2: ADDITIONAL REQUIREMENTS FOR STEEL CASTINGS |
| I.S. EN 10216-3:2013 | SEAMLESS STEEL TUBES FOR PRESSURE PURPOSES - TECHNICAL DELIVERY CONDITIONS - PART 3: ALLOY FINE GRAIN STEEL TUBES |
| I.S. EN 10273:2016 | HOT ROLLED WELDABLE STEEL BARS FOR PRESSURE PURPOSES WITH SPECIFIED ELEVATED TEMPERATURE PROPERTIES |
| I.S. EN 10314:2016 | METHOD FOR THE DERIVATION OF MINIMUM VALUES OF PROOF STRENGTH OF STEEL AT ELEVATED TEMPERATURES |
| DIN EN 10028-1:2017-10 | FLAT PRODUCTS MADE OF STEELS FOR PRESSURE PURPOSES - PART 1: GENERAL REQUIREMENTS |
| I.S. EN 10216-5:2013 | SEAMLESS STEEL TUBES FOR PRESSURE PURPOSES - TECHNICAL DELIVERY CONDITIONS - PART 5: STAINLESS STEEL TUBES |
| I.S. EN 10088-2:2014 | STAINLESS STEELS - PART 2: TECHNICAL DELIVERY CONDITIONS FOR SHEET/PLATE AND STRIP OF CORROSION RESISTING STEELS FOR GENERAL PURPOSES |
| I.S. EN 10217-7:2014 | WELDED STEEL TUBES FOR PRESSURE PURPOSES - TECHNICAL DELIVERY CONDITIONS - PART 7: STAINLESS STEEL TUBES |
| DIN EN 10088-2:2014-12 | STAINLESS STEELS - PART 2: TECHNICAL DELIVERY CONDITIONS FOR SHEET/PLATE AND STRIP OF CORROSION RESISTING STEELS FOR GENERAL PURPOSES |
| I.S. EN 12101-3:2015 | SMOKE AND HEAT CONTROL SYSTEMS - PART 3: SPECIFICATION FOR POWERED SMOKE AND HEAT CONTROL VENTILATORS (FANS) |
| I.S. EN 10269:2013 | STEELS AND NICKEL ALLOYS FOR FASTENERS WITH SPECIFIED ELEVATED AND/OR LOW TEMPERATURE PROPERTIES |
| I.S. EN 12952-2:2011 | WATER-TUBE BOILERS AND AUXILIARY INSTALLATIONS - PART 2: MATERIALS FOR PRESSURE PARTS OF BOILERS AND ACCESSORIES |
| I.S. EN 1559-2:2014 | FOUNDING - TECHNICAL CONDITIONS OF DELIVERY - PART 2 - ADDITIONAL REQUIREMENTS FOR STEEL CASTINGS |
| I.S. EN 10272:2016&LC:2016 | STAINLESS STEEL BARS FOR PRESSURE PURPOSES |
| I.S. EN 13480-8:2017&LC:2019 | METALLIC INDUSTRIAL PIPING - PART 8: ADDITIONAL REQUIREMENTS FOR ALUMINIUM AND ALUMINIUM ALLOY PIPING |
| I.S. EN 10088-3:2014 | STAINLESS STEELS - PART 3: TECHNICAL DELIVERY CONDITIONS FOR SEMI-FINISHED PRODUCTS, BARS, RODS, WIRE, SECTIONS AND BRIGHT PRODUCTS OF CORROSION RESISTING STEELS FOR GENERAL PURPOSES |
| DIN EN 10088-3:2014-12 | Stainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes |
| I.S. EN 764-4:2014 | PRESSURE EQUIPMENT - PART 4: ESTABLISHMENT OF TECHNICAL DELIVERY CONDITIONS FOR METALLIC MATERIALS |
| I.S. EN 10028-1:2017 | FLAT PRODUCTS MADE OF STEELS FOR PRESSURE PURPOSES - PART 1: GENERAL REQUIREMENTS |
| NF EN 12952-2 : 2011 | WATER-TUBE BOILERS AND AUXILIARY INSTALLATIONS - PART 2: MATERIALS FOR PRESSURE PARTS OF BOILERS AND ACCESSORIES |
| VDI 2700 Blatt 14:2011-09 | Securing of loads on road vehicles - Determination of coefficients of friction |
| VDI 3405 Blatt 2:2013-08 | Additive manufacturing processes, rapid manufacturing - Beam melting of metallic parts - Qualification, quality assurance and post processing |
| 12/30259070 DC : 0 | BS EN 764-4 - PRESSURE EQUIPMENT - PART 4: ESTABLISHMENT OF TECHNICAL DELIVERY CONDITIONS FOR METALLIC MATERIALS |
| EN 10217-7:2014 | Welded steel tubes for pressure purposes - Technical delivery conditions - Part 7: Stainless steel tubes |
| 13/30288578 DC : 0 | BS EN 10314 - METHOD FOR THE DERIVATION OF MINIMUM VALUES OF PROOF STRENGTH OF STEEL AT ELEVATED TEMPERATURES |
| NF EN 4800-005 : 2012 | AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 005: FORGING STOCK |
| I.S. EN 15566:2016 | RAILWAY APPLICATIONS - RAILWAY ROLLING STOCK - DRAW GEAR AND SCREW COUPLING |
| BS EN 4700-002:2016 | Aerospace series. Steel and heat resisting alloys. Wrought products. Technical specification Bar and section |
| 11/30254171 DC : 0 | BS EN 10088-2 - STAINLESS STEELS - PART 2: TECHNICAL DELIVERY CONDITIONS FOR SHEET/PLATE AND STRIP OF CORROSION RESISTING STEELS FOR GENERAL PURPOSES |
| BS EN 4800-006:2010 | Aerospace series. Titanium and titanium alloys. Technical specification Pre-production and production forgings |
| UNI EN 10216-5 : 2014 | SEAMLESS STEEL TUBES FOR PRESSURE PURPOSES - TECHNICAL DELIVERY CONDITIONS - PART 5: STAINLESS STEEL TUBES |
| 13/30288572 DC : 0 | BS EN 10272 - STAINLESS STEEL BARS FOR PRESSURE PURPOSES |
| BS EN 4800-005:2010 | Aerospace series. Titanium and titanium alloys. Technical specification Forging stock |
| 13/30288575 DC : 0 | BS EN 10273 - HOT ROLLED WELDABLE STEEL BARS FOR PRESSURE PURPOSES WITH SPECIFIED ELEVATED TEMPERATURE PROPERTIES |
| NF EN 4700-006 : 2012 | AEROSPACE SERIES - STEEL AND HEAT RESISTING ALLOYS - WROUGHT PRODUCTS - TECHNICAL SPECIFICATION - PART 006: PRE-PRODUCTION AND PRODUCTION FORGINGS |
| PREN 10222-1 : DRAFT 2012 | STEEL FORGINGS FOR PRESSURE PURPOSES - PART 1: GENERAL REQUIREMENTS |
| NF EN 4700-003 : 2012 | AEROSPACE SERIES - STEEL AND HEAT RESISTING ALLOYS - WROUGHT PRODUCTS - TECHNICAL SPECIFICATION - PART 003: TUBE |
| KTA 3211.1 : 2015 | PRESSURE AND ACTIVITY RETAINING COMPONENTS OF SYSTEMS OUTSIDE THE PRIMARY CIRCUIT - PART 1: MATERIALS |
| PREN 1559-2 : DRAFT 2012 | FOUNDING - TECHNICAL CONDITIONS OF DELIVERY - PART 2: ADDITIONAL REQUIREMENTS FOR STEEL CASTINGS |
| UNE-EN 10088-2:2015 | Stainless steels - Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes |
| DIN EN 10216-3:2014-03 | SEAMLESS STEEL TUBES FOR PRESSURE PURPOSES - TECHNICAL DELIVERY CONDITIONS - PART 3: ALLOY FINE GRAIN STEEL TUBES |
| UNI EN 10216-2 : 2014 | SEAMLESS STEEL TUBES FOR PRESSURE PURPOSES - TECHNICAL DELIVERY CONDITIONS - PART 2: NON-ALLOY AND ALLOY STEEL TUBES WITH SPECIFIED ELEVATED TEMPERATURE PROPERTIES |
| UNE-EN 10216-2:2014 | Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 2: Non-alloy and alloy steel tubes with specified elevated temperature properties |
| BS EN 10217-7:2014 | Welded steel tubes for pressure purposes. Technical delivery conditions Stainless steel tubes |
| UNE-EN 764-4:2015 | Pressure equipment - Part 4: Establishment of technical delivery conditions for metallic materials |
| UNE-EN 10088-3:2015 | Stainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes |
| UNI EN 10269 : 2013 | Nickel steels and alloys for fasteners with specific properties at high and / or low temperatures |
| UNI EN 10088-3 : 2014 | STAINLESS STEELS - PART 3: TECHNICAL DELIVERY CONDITIONS FOR SEMIFINISHED PRODUCTS, BARS, RODS, WIRE, SECTIONS AND BRIGHT PRODUCTS OF CORROSION RESISTING STEELS FOR GENERAL PURPOSES |
| EN 1559-2:2014 | Founding - Technical conditions of delivery - Part 2: Additional requirements for steel castings |
| UNI EN 12952-2 : 2011 | WATER-TUBE BOILERS AND AUXILIARY INSTALLATIONS - PART 2: MATERIALS FOR PRESSURE PARTS OF BOILERS AND ACCESSORIES |
| UNI EN 1559-2 : 2014 | FOUNDING - TECHNICAL CONDITIONS OF DELIVERY - PART 2: ADDITIONAL REQUIREMENTS FOR STEEL CASTINGS |
| UNI EN 10218-1 : 2012 | STEEL WIRE AND WIRE PRODUCTS - GENERAL - PART 1: TEST METHODS |
| UNI EN 10088-2:2014 | STAINLESS STEELS - PART 2: TECHNICAL DELIVERY CONDITIONS FOR SHEET/PLATE AND STRIP OF CORROSION RESISTING STEELS FOR GENERAL PURPOSES |
| UNI EN 10216-3 : 2014 | SEAMLESS STEEL TUBES FOR PRESSURE PURPOSES - TECHNICAL DELIVERY CONDITIONS - PART 3: ALLOY FINE GRAIN STEEL TUBES |
| 16/30352446 DC : 0 | BS EN 3833 - AEROSPACE SERIES - BOLTS, MJ THREADS, IN HEAT RESISTING NICKEL BASE ALLOY NI-PH2601 (INCONEL 718), PASSIVATED - CLASSIFICATION: 1550 MPA (AT AMBIENT TEMPERATURE)/650 DEGREES C - TECHNICAL SPECIFICATION |
| NF EN 4800-008 : 2012 | AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 008: PRE-PRODUCTION AND PRODUCTION CASTINGS |
| NF EN 4800-007 : 2012 | AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 007: REMELTING STOCK |
| EN 10216-5:2013 | Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 5: Stainless steel tubes |
| 12/30266615 DC : 0 | BS EN 1559-2 - FOUNDING - TECHNICAL CONDITIONS OF DELIVERY - PART 2: ADDITIONAL REQUIREMENTS FOR STEEL CASTINGS |
| 11/30254168 DC : 0 | BS EN 10088-3 - STAINLESS STEELS - PART 3: TECHNICAL DELIVERY CONDITIONS FOR SEMI-FINISHED PRODUCTS, BARS, RODS, WIRE, SECTIONS AND BRIGHT PRODUCTS OF CORROSION RESISTING STEELS FOR GENERAL PURPOSES |
| PREN 10253-4 : DRAFT 2017 | BUTT-WELDING PIPE FITTINGS - PART 4: WROUGHT AUSTENITIC & AUSTENITIC-FERRITIC (DUPLEX) STAINLESS STEELS WITH SPECIFIC INSPECTION REQUIREMENTS |
| 11/30253929 DC : 0 | BS EN 4820 - AEROSPACE SERIES - COPPER AND COPPER ALLOYS - WROUGHT PRODUCTS - TECHNICAL SPECIFICATION |
| NF EN 4700-001 : 2012 | AEROSPACE SERIES - STEEL AND HEAT RESISTING ALLOYS - WROUGHT PRODUCTS - TECHNICAL SPECIFICATION - PART 001: PLATE, SHEET AND STRIP |
| NF EN 4700-004 : 2012 | AEROSPACE SERIES - STEEL AND HEAT RESISTING ALLOYS - WROUGHT PRODUCTS - TECHNICAL SPECIFICATION - PART 004: WIRE |
| NF EN 4800-004 : 2012 | AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 004: WIRE |
| PREN 3833 : 200P3 | AEROSPACE SERIES - BOLTS, MJ THREADS, IN HEAT RESISTING NICKEL BASE ALLOY NI-PH2601 (INCONEL 718), PASSIVATED - CLASSIFICATION: 1550 MPA (AT AMBIENT TEMPERATURE)/650 DEGREES C - TECHNICAL SPECIFICATION |
| NF EN 4800-001 : 2012 | AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 001: PLATE, SHEET AND STRIP |
| I.S. EN 10207:2017 | STEELS FOR SIMPLE PRESSURE VESSELS - TECHNICAL DELIVERY REQUIREMENTS FOR PLATES, STRIPS AND BARS |
| PREN 10269 : DRAFT 2011 | STEELS AND NICKEL ALLOYS FOR FASTENERS WITH SPECIFIED ELEVATED AND/OR LOW TEMPERATURE PROPERTIES |
| PREN 10273 : DRAFT 2013 | HOT ROLLED WELDABLE STEEL BARS FOR PRESSURE PURPOSES WITH SPECIFIED ELEVATED TEMPERATURE PROPERTIES |
| BS EN 10207:2017 | Steels for simple pressure vessels. Technical delivery requirements for plates, strips and bars |
| EN 10216-2:2013 | Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 2: Non-alloy and alloy steel tubes with specified elevated temperature properties |
| DIN EN 10217-7:2015-01 | Welded steel tubes for pressure purposes - Technical delivery conditions - Part 7: Stainless steel tubes |
| DIN EN 10314:2016-10 | METHOD FOR THE DERIVATION OF MINIMUM VALUES OF PROOF STRENGTH OF STEEL AT ELEVATED TEMPERATURES |
| DIN EN 10272:2016-10 | STAINLESS STEEL BARS FOR PRESSURE PURPOSES |
| BS EN 1559-2:2014 | Founding. Technical conditions of delivery Additional requirements for steel castings |
| BS EN 10216-5:2013 | Seamless steel tubes for pressure purposes. Technical delivery conditions Stainless steel tubes |
| BS EN 10216-3:2013 | Seamless steel tubes for pressure purposes. Technical delivery conditions Alloy fine grain steel tubes |
| UNE-EN 12952-2:2012 | Water-tube boilers and auxiliary installations - Part 2: Materials for pressure parts of boilers and accessories |
| BS EN 10218-1:2012 | Steel wire and wire products. General Test methods |
| BS EN 764-4:2014 | Pressure equipment Establishment of technical delivery conditions for metallic materials |
| BS EN 10314:2002 | Method for the derivation of minimum values of proof strength of steel at elevated temperatures |
| BS EN 10088-3:2014 | Stainless steels Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes |
| UNE-EN 10269:2014 | Steels and nickel alloys for fasteners with specified elevated and/or low temperature properties |
| UNE-EN 10216-3:2014 | Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 3: Alloy fine grain steel tubes |
| UNE-EN 10028-1:2017 | Flat products made of steels for pressure purposes - Part 1: General requirements |
| UNE-EN 10216-5:2014 | Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 5: Stainless steel tubes |
| UNE-EN 10218-1:2012 | Steel wire and wire products - General - Part 1: Test methods |
| EN 15566:2016 | Railway applications - Railway rolling stock - Draw gear and screw coupling |
| EN 4800-006:2010 | Aerospace series - Titanium and titanium alloys - Technical specification - Part 006: Pre-production and production forgings |
| EN 4800-005:2010 | Aerospace series - Titanium and titanium alloys - Technical specification - Part 005: Forging stock |
| EN 764-4:2014 | Pressure equipment - Part 4: Establishment of technical delivery conditions for metallic materials |
| EN 13480-8:2017 | Metallic industrial piping - Part 8: Additional requirements for aluminium and aluminium alloy piping |
| UNE-EN 15566:2017 | Railway applications - Railway rolling stock - Draw gear and screw coupling |
| I.S. EN 4700-002:2016 | AEROSPACE SERIES - STEEL AND HEAT RESISTING ALLOYS - WROUGHT PRODUCTS - TECHNICAL SPECIFICATION - PART 002: BAR AND SECTION |
| 14/30312182 DC : 0 | BS EN 10028-1 - FLAT PRODUCTS MADE OF STEELS FOR PRESSURE PURPOSES - PART 1: GENERAL REQUIREMENTS |
| PREN 10088-3 : DRAFT 2011 | STAINLESS STEELS - PART 3: TECHNICAL DELIVERY CONDITIONS FOR SEMI-FINISHED PRODUCTS, BARS, RODS, WIRE, SECTIONS AND BRIGHT PRODUCTS OF CORROSION RESISTING STEELS FOR GENERAL PURPOSES |
| 15/30317351 DC : 0 | BS EN 13480-8:2012/A2 - METALLIC INDUSTRIAL PIPING - PART 8: ADDITIONAL REQUIREMENTS FOR ALUMINIUM AND ALUMINIUM ALLOY PIPING |
| 15/30331537 DC : 0 | BS EN 10207 - STEELS FOR SIMPLE PRESSURE VESSELS - TECHNICAL DELIVERY REQUIREMENTS FOR PLATES, STRIPS AND BARS |
| PREN 4700-002 : 200P3 | AEROSPACE SERIES - STEEL AND HEAT RESISTING ALLOYS WROUGHT PRODUCTS - TECHNICAL SPECIFICATION - PART 002: BAR AND SECTION |
| KTA 3206 : 2014(R2017)Berichtigung:2019 | BREAK PRECLUSION VERIFICATIONS FOR PRESSURE-RETAINING COMPONENTS IN NUCLEAR POWER PLANTS |
| DIN EN 764-4:2015-03 | PRESSURE EQUIPMENT - PART 4: ESTABLISHMENT OF TECHNICAL DELIVERY CONDITIONS FOR METALLIC MATERIALS |
| DIN EN 12952-2:2011-10 | Water-tube boilers and auxiliary installations - Part 2: Materials for pressure parts of boilers and accessories |
| BS EN 10269:2013 | Steels and nickel alloys for fasteners with specified elevated and/or low temperature properties |
| BS EN 10088-2:2014 | Stainless steels Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes |
| UNE-EN 10273:2016 | Hot rolled weldable steel bars for pressure purposes with specified elevated temperature properties |
| UNE-EN 10222-1:2017 | Steel forgings for pressure purposes - Part 1: General requirements for open die forgings |
| BS EN 10222-1:2017 | Steel forgings for pressure purposes General requirements for open die forgings |
| BS EN 12952-2:2011 | Water-tube boilers and auxiliary installations Materials for pressure parts of boilers and accessories |
| BS EN 10028-1:2017 | Flat products made of steels for pressure purposes General requirements |
| BS EN 10273:2016 | Hot rolled weldable steel bars for pressure purposes with specified elevated temperature properties |
| EN 10216-3:2013 | Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 3: Alloy fine grain steel tubes |
| ISO 2566-2:1984 | Steel Conversion of elongation values Part 2: Austenitic steels |
| ISO 6892-1:2016 | Metallic materials Tensile testing Part 1: Method of test at room temperature |
| ISO 9513:2012 | Metallic materials — Calibration of extensometer systems used in uniaxial testing |
| ISO 2566-1:1984 | Steel Conversion of elongation values Part 1: Carbon and low alloy steels |
| ISO 80000-1:2009 | Quantities and units — Part 1: General |
| ISO 7500-1:2015 | Metallic materials Calibration and verification of static uniaxial testing machines Part 1: Tension/compression testing machines Calibration and verification of the force-measuring system |
| ISO 377:2017 | Steel and steel products — Location and preparation of samples and test pieces for mechanical testing |
| ISO 2142:1981 | Wrought aluminium, magnesium and their alloys Selection of specimens and test pieces for mechanical testing |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.