EN ISO 15607:2003
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Specification and qualification of welding procedures for metallic materials - General rules (ISO 15607:2003)
Superseded date
11-04-2019
Superseded by
Published date
12-15-2003
Publisher
Sorry this product is not available in your region.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Abbreviations
5 Welding procedure specification format
6 Development and qualification of welding procedures
6.1 General
6.2 Qualification based on welding procedure test
6.3 Qualification based on tested welding consumables
6.4 Qualification based on previous welding experience
6.5 Qualification based on a standard welding procedure
6.6 Qualification based on a pre-production welding test
7 Validity
Annex A (informative) New numbering system - Details of the
standards dealing with specification
and qualification of welding procedures
Annex B (informative) Different phases in welding procedure
qualification
Annex C (informative) Flow diagram for the development and
qualification of a WPS
Bibliography
ISO 15607:2003 defines general rules for the specification and qualification of welding procedures for metallic materials.It also refers to several other standards as regards detailed rules for specific applications. ISO 15607:2003 is applicable to manual, mechanized and automatic welding.
| Committee |
CEN/TC 121
|
| DevelopmentNote |
Supersedes EN 288-1 (12/2003)
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| DIN EN ISO 15607:2004-03 | Identical |
| ONORM EN ISO 15607 : 2004 | Identical |
| ISO 15607:2003 | Identical |
| UNE-EN ISO 15607:2004 | Identical |
| NBN EN ISO 15607 : 2004 | Identical |
| NF EN ISO 15607 : 2004 | Identical |
| NEN EN ISO 15607 : 2003 | Identical |
| NS EN ISO 15607 : 1ED 2004 | Identical |
| I.S. EN ISO 15607:2004 | Identical |
| PN EN ISO 15607 : 2007 | Identical |
| SN EN ISO 15607 : 2004 | Identical |
| UNI EN ISO 15607 : 2005 | Identical |
| DIN EN ISO 15607:2018-11 (Draft) | Identical |
| SS-EN ISO 15607:2004 | Identical |
| BS EN ISO 15607:2003 | Identical |
| 14/30294476 DC : 0 | BS EN 448 - DISTRICT HEATING PIPES - PREINSULATED BONDED PIPE SYSTEMS FOR DIRECTLY BURIED HOT WATER NETWORKS - FITTING ASSEMBLIES OF STEEL SERVICE PIPES, POLYURETHANE THERMAL INSULATION AND OUTER CASING OF POLYETHYLENE |
| I.S. EN ISO 15611:2004 | SPECIFICATION AND QUALIFICATION OF WELDING PROCEDURES FOR METALLIC MATERIALS - QUALIFICATION BASED ON PREVIOUS WELDING EXPERIENCE |
| I.S. EN 12079-1:2006 | OFFSHORE CONTAINERS AND ASSOCIATED LIFTING SETS - PART 1: OFFSHORE CONTAINERS - DESIGN, MANUFACTURE AND MARKING |
| I.S. EN ISO 15614-2:2005 | SPECIFICATION AND QUALIFICATION OF WELDING PROCEDURES FOR METALLIC MATERIALS - WELDING PROCEDURE TEST - PART 2: ARC WELDING OF ALUMINIUM AND ITS ALLOYS |
| I.S. EN 14341:2006 | INDUSTRIAL VALVES - STEEL CHECK VALVES |
| I.S. EN 287-1:2011 | QUALIFICATION TEST OF WELDERS - FUSION WELDING - PART 1: STEELS |
| BS EN 593:2017 | Industrial valves. Metallic butterfly valves for general purposes |
| BS EN 16767:2016 | Industrial valves. Steel and cast iron check valves |
| 14/30258527 DC : 0 | BS EN 16725 - RAILWAY APPLICATIONS - TRACK - RESTORATION AND REPAIR OF MANGANESE CROSSINGS |
| 09/30186082 DC : 0 | BS EN 13110 - LPG EQUIPMENT AND ACCESSORIES - TRANSPORTABLE REFILLABLE WELDED ALUMINIUM CYLINDERS FOR LIQUEFIED PETROLEUM GAS - DESIGN AND CONSTRUCTION |
| UNE-EN 16767:2017 | Industrial valves - Steel and cast iron check valves |
| DIN EN 12496:2014-02 | GALVANIC ANODES FOR CATHODIC PROTECTION IN SEAWATER AND SALINE MUD |
| 11/30253745 DC : 0 | BS EN 14025 - TANKS FOR THE TRANSPORT OF DANGEROUS GOODS - METALLIC PRESSURE TANKS - DESIGN AND CONSTRUCTION |
| 14/30301577 DC : 0 | BS EN 16767 - INDUSTRIAL VALVES - STEEL AND CAST IRON CHECK VALVES |
| BS EN 15594:2009 | Railway applications. Track. Restoration of rails by electric arc welding |
| PREN 1069-2 : DRAFT 2015 | WATER SLIDES - PART 2: INSTRUCTIONS |
| I.S. EN 16725:2016 | RAILWAY APPLICATIONS - TRACK - RESTORATION AND REPAIR OF MANGANESE CROSSINGS |
| I.S. EN ISO 15612:2004 | SPECIFICATION AND QUALIFICATION OF WELDING PROCEDURES FOR METALLIC MATERIALS - QUALIFICATION BY ADOPTION OF A STANDARD WELDING PROCEDURE |
| 16/30334287 DC : 0 | BS EN 334 - GAS PRESSURE REGULATORS FOR INLET PRESSURE UP TO 100 BAR |
| 18/30369304 DC : DRAFT APR 2018 | BS EN 1473 - INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN OF ONSHORE INSTALLATIONS |
| 16/30319005 DC : 0 | BS EN 12285-1 - WORKSHOP FABRICATED STEEL TANKS - PART 1: HORIZONTAL CYLINDRICAL SINGLE SKIN AND DOUBLE SKIN TANKS FOR THE UNDERGROUND STORAGE OF FLAMMABLE AND NONFLAMMABLE WATER POLLUTING LIQUIDS OTHER THAN FOR HEATING AND COOLING OF BUILDINGS |
| 17/30362892 DC : 0 | BS EN 14025 - TANKS FOR THE TRANSPORT OF DANGEROUS GOODS - METALLIC PRESSURE TANKS - DESIGN AND CONSTRUCTION |
| UNI EN 1090-1 : 2012 | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 1: REQUIREMENTS FOR CONFORMITY ASSESSMENT OF STRUCTURAL COMPONENTS |
| DIN EN 334:2016-05 (Draft) | GAS PRESSURE REGULATORS FOR INLET PRESSURES UP TO 100 BAR |
| ISO 15614-2:2005 | Specification and qualification of welding procedures for metallic materials Welding procedure test Part 2: Arc welding of aluminium and its alloys |
| I.S. EN 14382:2005 | SAFETY DEVICES FOR GAS PRESSURE REGULATING STATIONS AND INSTALLATIONS - GAS SAFETY SHUT-OFF DEVICES FOR INLET PRESSURES UP TO 100 BAR |
| I.S. EN ISO 15609-1:2004 | SPECIFICATION AND QUALIFICATION OF WELDING PROCEDURES FOR METALLIC MATERIALS - WELDING PROCEDURE SPECIFICATION - PART 1: ARC WELDING |
| DIN EN 15085-2:2008-01 | RAILWAY APPLICATIONS - WELDING OF RAILWAY VEHICLES AND COMPONENTS - PART 2: QUALITY REQUIREMENTS AND CERTIFICATION OF WELDING MANUFACTURER |
| UNI EN ISO 15609-1 : 2006 | SPECIFICATION AND QUALIFICATION OF WELDING PROCEDURES FOR METALLIC MATERIALS - WELDING PROCEDURE SPECIFICATION - PART 1: ARC WELDING |
| I.S. EN 448:2015 | DISTRICT HEATING PIPES - PREINSULATED BONDED PIPE SYSTEMS FOR DIRECTLY BURIED HOT WATER NETWORKS - FITTING ASSEMBLIES OF STEEL SERVICE PIPES, POLYURETHANE THERMAL INSULATION AND OUTER CASING OF POLYETHYLENE |
| EN 10222-1:2017 | Steel forgings for pressure purposes - Part 1: General requirements for open die forgings |
| DIN EN 13709:2010-10 | Industrial valves - Steel globe and globe stop and check valves |
| DIN EN 1759-1:2005-02 | Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, Class designated - Part 1: Steel flanges, NPS 1/2 to 24 |
| DIN EN 12732:2014-07 | Gas infrastructure - Welding steel pipework - Functional requirements (includes Amendment A1:2014) |
| DIN EN 10163-1:2005-03 | DELIVERY REQUIREMENTS FOR SURFACE CONDITION OF HOT-ROLLED STEEL PLATES, WIDE FLATS AND SECTIONS - PART 1: GENERAL REQUIREMENTS |
| DIN EN 12972:2015-04 | TANKS FOR TRANSPORT OF DANGEROUS GOODS - TESTING, INSPECTION AND MARKING OF METALLIC TANKS |
| DIN EN 1473:2016-10 | Installation and equipment for liquefied natural gas - Design of onshore installations |
| DIN EN 10208-1:2009-07 | STEEL PIPES FOR PIPELINES FOR COMBUSTIBLE FLUIDS - TECHNICAL DELIVERY CONDITIONS - PART 1: PIPES OF REQUIREMENT CLASS A |
| 13/30280057 DC : 0 | BS EN 13782 - TEMPORARY STRUCTURE - TENTS - SAFETY |
| UNE-EN 1069-2:2017 | Water slides - Part 2: Instructions |
| BS EN 14208:2004 | Transportable gas cylinders. Specification for welded pressure drums up to 1000 litre capacity for the transport of gases. Design and construction |
| BS EN 13807:2017 | Transportable gas cylinders. Battery vehicles and multiple-element gas containers (MEGCs). Design, manufacture, identification and testing |
| BS EN 12811-2:2004 | Temporary works equipment Information on materials |
| BS EN 14382 : 2005 | SAFETY DEVICES FOR GAS PRESSURE REGULATING STATIONS AND INSTALLATIONS - GAS SAFETY SHUT-OFF DEVICES FOR INLET PRESSURES UP TO 100 BAR |
| I.S. EN 14276-1:2006 | PRESSURE EQUIPMENT FOR REFRIGERATING SYSTEMS AND HEAT PUMPS - PART 1: VESSELS - GENERAL REQUIREMENTS |
| BS EN 14015:2004 | Specification for the design and manufacture of site built, vertical, cylindrical, flat-bottomed, above ground, welded, steel tanks for the storage of liquids at ambient temperature and above |
| BS EN 1984:2010 | Industrial valves. Steel gate valves |
| BS EN 489:2009 | District heating pipes. Preinsulated bonded pipe systems for directly buried hot water networks. Joint assembly for steel service pipes, polyurethane thermal insulation and outer casing of polyethylene |
| BS EN ISO 15609-3:2004 | Specification and qualification of welding procedures for metallic materials. Welding procedure specification Electron beam welding |
| I.S. EN 10222-1:2017 | STEEL FORGINGS FOR PRESSURE PURPOSES - PART 1: GENERAL REQUIREMENTS FOR OPEN DIE FORGINGS |
| I.S. EN 1069-2:2017 | WATER SLIDES - PART 2: INSTRUCTIONS |
| EN 12811-2:2004 | Temporary works equipment - Part 2: Information on materials |
| EN 12496:2013 | Galvanic anodes for cathodic protection in seawater and saline mud |
| EN 12285-2:2005 | Workshop fabricated steel tanks - Part 2: Horizontal cylindrical single skin and double skin tanks for the aboveground storage of flammable and non-flammable water polluting liquids |
| EN 10219-1:2006 | Cold formed welded structural hollow sections of non-alloy and fine grain steels - Part 1: Technical delivery conditions |
| EN 10210-1:2006 | Hot finished structural hollow sections of non-alloy and fine grain steels - Part 1: Technical delivery conditions |
| EN 1069-2:2017 | Water slides - Part 2: Instructions |
| EN 10311:2005 | Joints for the connection of steel tubes and fittings for the conveyance of water and other aqueous liquids |
| DIN EN 12811-2:2004-04 | Temporary works equipment - Part 2: Information on materials; German version EN 12811-2:2004 |
| EN 10208-1:2009 | Steel pipes for pipelines for combustible fluids - Technical delivery condi-tions - Part 1: Pipes of requirement class A |
| EN 1090-1:2009+A1:2011 | Execution of steel structures and aluminium structures - Part 1: Requirements for conformity assessment of structural components |
| EN 12693:2008 | Refrigerating systems and heat pumps - Safety and environmental requirements - Positive displacement refrigerant compressors |
| EN 1011-1:2009 | Welding - Recommendations for welding of metallic materials - Part 1: General guidance for arc welding |
| EN 13110:2012+A1:2017 | LPG equipment and accessories - Transportable refillable welded aluminium cylinders for liquefied petroleum gas (LPG) - Design and construction |
| UNI EN 12732 : 2014 | GAS INFRASTRUCTURE - WELDING STEEL PIPEWORK - FUNCTIONAL REQUIREMENTS |
| EN 14423:2013+A1:2016 | Clamp type coupling assemblies for use with steam hoses rated for pressures up to 18 bar |
| DIN EN ISO 15612:2016-09 (Draft) | SPECIFICATION AND QUALIFICATION OF WELDING PROCEDURES FOR METALLIC MATERIALS - QUALIFICATION BY ADOPTION OF A STANDARD WELDING PROCEDURE |
| 09/30186448 DC : 0 | BS EN 13941 - DESIGN AND INSTALLATION OF REINSULATED BONDED PIPE SYSTEMS FOR DISTRICT HEATING |
| I.S. EN ISO 15613:2004 | SPECIFICATION AND QUALIFICATION OF WELDING PROCEDURES FOR METALLIC MATERIALS - QUALIFICATION BASED ON PRE-PRODUCTION WELDING TEST |
| I.S. EN ISO 15609-3:2004 | SPECIFICATION AND QUALIFICATION OF WELDING PROCEDURES FOR METALLIC MATERIALS - WELDING PROCEDURES SPECIFICATION - PART 3: ELECTRON BEAM WELDING |
| BS EN 1090-1 : 2009 | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 1: REQUIREMENTS FOR CONFORMITY ASSESSMENT OF STRUCTURAL COMPONENTS |
| I.S. EN 13611:2015 | SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS AND/OR LIQUID FUELS - GENERAL REQUIREMENTS |
| 12/30270633 DC : 0 | BS EN 10222-1 - STEEL FORGINGS FOR PRESSURE PURPOSES - PART 1: GENERAL REQUIREMENTS |
| DIN EN 15001-1:2011-02 | Gas infrastructure - Gas installation pipework with an operating pressure greater than 0,5 bar for industrial installations and greater than 5 bar for industrial and non-industrial installations - Part 1: Detailed functional requirements for design, materials, construction, inspection and testing |
| DIN EN 15594:2009-08 | RAILWAY APPLICATIONS - TRACK - RESTORATION OF RAILS BY ELECTRIC ARC WELDING |
| PREN 13709 : DRAFT 2009 | INDUSTRIAL VALVES - STEEL GLOBE AND GLOBE STOP AND CHECK VALVES |
| PREN 1984 : DRAFT 2009 | INDUSTRIAL VALVES - STEEL GATE VALVES |
| UNE-EN 1090-1:2011 | Execution of steel structures and aluminium structures - Part 1: Requirements for conformity assessment of structural components |
| BS EN 12693:2008 | Refrigerating systems and heat pumps. Safety and environmental requirements. Positive displacement refrigerant compressors |
| I.S. EN 593:2017 | INDUSTRIAL VALVES - METALLIC BUTTERFLY VALVES FOR GENERAL PURPOSES |
| ONORM EN 334 : JUN 2009 | GAS PRESSURE REGULATORS FOR INLET PRESSURES UP TO 100 BAR |
| PREN 764-4 : DRAFT 2012 | PRESSURE EQUIPMENT - PART 4: ESTABLISHMENT OF TECHNICAL DELIVERY CONDITIONS FOR METALLIC MATERIALS |
| 16/30328759 DC : 0 | BS EN 13814-1 - SAFETY OF AMUSEMENT RIDES AND AMUSEMENT DEVICES - PART 1: DESIGN AND MANUFACTURE |
| PREN 448 : DRAFT 2018 | DISTRICT HEATING PIPES - PREINSULATED BONDED PIPE SYSTEMS FOR DIRECTLY BURIED HOT WATER NETWORKS - FITTING ASSEMBLIES OF STEEL SERVICE PIPES, POLYURETHANE THERMAL INSULATION AND OUTER CASING OF POLYETHYLENE |
| BS EN 13611:2015 | Safety and control devices for burners and appliances burning gaseous and/or liquid fuels. General requirements |
| 17/30360051 DC : 0 | BS EN 13611 - SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS AND/OR LIQUID FUELS - GENERAL REQUIREMENTS |
| DIN EN 1011-1:2009-07 | WELDING - RECOMMENDATIONS FOR WELDING OF METALLIC MATERIALS - PART 1: GENERAL GUIDANCE FOR ARC WELDING |
| DIN EN 12285-2:2005-05 | WORKSHOP FABRICATED STEEL TANKS - PART 2: HORIZONTAL CYLINDRICAL SINGLE SKIN AND DOUBLE SKIN TANKS FOR THE ABOVEGROUND STORAGE OF FLAMMABLE AND NON-FLAMMABLE WATER POLLUTING LIQUIDS |
| DIN EN 1984:2010-10 | Industrial valves - Steel gate valves |
| DIN EN ISO 15614-2:2005-07 | Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 2: Arc welding of aluminium and its alloys (ISO 15614-2:2005); German version EN ISO 15614-2:2005 |
| BS EN 334 : 2005 | GAS PRESSURE REGULATORS FOR INLET PRESSURES UP TO 100 BAR |
| BS EN 287-1:2011 | Qualification test of welders. Fusion welding Steels |
| BS EN 1473:2016 | Installation and equipment for liquefied natural gas. Design of onshore installations |
| UNE-EN 593:2009 | Industrial valves - Metallic butterfly valves |
| BS EN 13709:2002 | Industrial valves. Steel globe and globe stop and check valves |
| ISO 15609-3:2004 | Specification and qualification of welding procedures for metallic materials — Welding procedure specification — Part 3: Electron beam welding |
| DIN EN 1775:2007-10 | Gas supply - Gas pipework for buildings - Maximum operating pressure less than or equal to 5 bar - Functional recommendations |
| DIN EN 1473:1997-11 | INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN OF ONSHORE INSTALLATIONS |
| DIN EN 13611:2019-06 | Safety and control devices for burners and appliances burning gaseous and/or liquid fuels - General requirements |
| DIN EN 10208-1:1998-02 | STEEL PIPES FOR PIPELINES FOR COMBUSTIBLE FLUIDS - TECHNICAL DELIVERY CONDITIONS - PART 1: PIPES OF REQUIREMENT CLASS A |
| DIN EN 10210-1:2006-07 | Hot finished structural hollow sections of non-alloy and fine grain steels - Part 1: Technical delivery conditions |
| DIN EN 13084-1:2007-05 | Free-standing chimneys - Part 1: General requirements |
| I.S. EN 1984:2010 | INDUSTRIAL VALVES - STEEL GATE VALVES |
| I.S. EN 1011-1:2009 | WELDING - RECOMMENDATIONS FOR WELDING OF METALLIC MATERIALS - PART 1: GENERAL GUIDANCE FOR ARC WELDING |
| I.S. EN 12732:2013 | GAS INFRASTRUCTURE - WELDING STEEL PIPEWORK - FUNCTIONAL REQUIREMENTS |
| I.S. EN 13807:2017 | TRANSPORTABLE GAS CYLINDERS - BATTERY VEHICLES - DESIGN, MANUFACTURE, IDENTIFICATION AND TESTING |
| I.S. EN 10163-1:2005 | DELIVERY REQUIREMENTS FOR SURFACE CONDITION OF HOT-ROLLED STEEL PLATES, WIDE FLATS AND SECTIONS - PART 1: GENERAL REQUIREMENTS |
| DIN EN 13110:2017-05 | LPG EQUIPMENT AND ACCESSORIES - TRANSPORTABLE REFILLABLE WELDED ALUMINIUM CYLINDERS FOR LIQUEFIED PETROLEUM GAS (LPG) - DESIGN AND CONSTRUCTION |
| I.S. EN 10219-1:2006 | COLD FORMED WELDED STRUCTURAL HOLLOW SECTIONS OF NON-ALLOY AND FINE GRAIN STEELS - PART 1: TECHNICAL DELIVERY CONDITIONS |
| I.S. EN 1473:2016 | INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN OF ONSHORE INSTALLATIONS |
| I.S. EN 13941:2009 | DESIGN AND INSTALLATION OF PREINSULATED BONDED PIPE SYSTEMS FOR DISTRICT HEATING |
| I.S. EN 13084-1:2007 | FREE-STANDING CHIMNEYS - PART 1: GENERAL REQUIREMENTS |
| I.S. EN 14394:2006 | HEATING BOILERS - HEATING BOILERS WITH FORCED DRAUGHT BURNERS - NOMINAL HEAT OUTPUT NOT EXCEEDING 10 MW AND MAXIMUM OPERATING TEMPERATURE OF 110 DEGREE C |
| I.S. EN 10210-1:2006 | HOT FINISHED STRUCTURAL HOLLOW SECTIONS OF NON-ALLOY AND FINE GRAIN STEELS - PART 1: TECHNICAL DELIVERY CONDITIONS |
| NF EN 14276-1 : 2006 + A1 2011 | PRESSURE EQUIPMENT FOR REFRIGERATING SYSTEMS AND HEAT PUMPS - PART 1: VESSELS - GENERAL REQUIREMENTS |
| I.S. EN 13709:2010 | INDUSTRIAL VALVES - STEEL GLOBE AND GLOBE STOP AND CHECK VALVES |
| I.S. EN 764-4:2014 | PRESSURE EQUIPMENT - PART 4: ESTABLISHMENT OF TECHNICAL DELIVERY CONDITIONS FOR METALLIC MATERIALS |
| I.S. EN 1775:2007 | GAS SUPPLY - GAS PIPEWORK FOR BUILDINGS - MAXIMUM OPERATING PRESSURE LESS THAN OR EQUAL TO 5 BAR - FUNCTIONAL RECOMMENDATIONS |
| DIN EN 12732:2000-09 | GAS INFRASTRUCTURE - WELDING STEEL PIPEWORK - FUNCTIONAL REQUIREMENTS |
| UNI EN ISO 15613 : 2005 | SPECIFICATION AND QUALIFICATION OF WELDING PROCEDURES FOR METALLIC MATERIALS - QUALIFICATION BASED ON PRE-PRODUCTION WELDING TEST |
| 16/30332608 DC : DRAFT JAN 2016 | BS EN 10210-2 - HOT FINISHED STRUCTURAL STEEL HOLLOW SECTIONS - PART 2: TECHNICAL DELIVERY CONDITIONS |
| 06/30156796 DC : 0 | BS EN 15594 - RAILWAY APPLICATIONS - TRACK - RESTORATION OF RAILS BY ELECTRIC ARC WELDING |
| UNI EN 12693 : 2008 | REFRIGERATING SYSTEMS AND HEAT PUMPS - SAFETY AND ENVIRONMENTAL REQUIREMENTS - POSITIVE DISPLACEMENT REFRIGERANT COMPRESSORS |
| 16/30319008 DC : 0 | BS EN 12285-3 - WORKSHOP FABRICATED STEEL TANKS - PART 3: HORIZONTAL CYLINDRICAL SINGLE SKIN AND DOUBLE SKIN TANKS FOR THE UNDERGROUND STORAGE OF FLAMMABLE AND NONFLAMMABLE WATER POLLUTING LIQUIDS FOR HEATING AND COOLING OF BUILDINGS |
| PREN 1473 : DRAFT 2018 | INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN OF ONSHORE INSTALLATIONS |
| 09/30205877 DC : 0 | BS EN 1984 - INDUSTRIAL VALVES - STEEL GATE VALVES |
| 12/30259070 DC : 0 | BS EN 764-4 - PRESSURE EQUIPMENT - PART 4: ESTABLISHMENT OF TECHNICAL DELIVERY CONDITIONS FOR METALLIC MATERIALS |
| I.S. EN 15001-1:2009 | GAS INFRASTRUCTURE - GAS INSTALLATION PIPEWORK WITH AN OPERATING PRESSURE GREATER THAN 0,5 BAR FOR INDUSTRIAL INSTALLATIONS AND GREATER THAN 5 BAR FOR INDUSTRIAL AND NON-INDUSTRIAL INSTALLATIONS - PART 1: DETAILED FUNCTIONAL REQUIREMENTS FOR DESIGN, MATERIALS, CONSTRUCTION, INSPECTION AND TESTING |
| DIN EN 10253-4:2008-06 | BUTT-WELDING PIPE FITTINGS - PART 4: WROUGHT AUSTENITIC AND AUSTENITIC-FERRITIC (DUPLEX) STAINLESS STEELS WITH SPECIFIC INSPECTION REQUIREMENTS |
| 13/30247837 DC : 0 | BS EN 13094 - TANKS FOR THE TRANSPORT OF DANGEROUS GOODS - METALLIC TANKS WITH A WORKING PRESSURE NOT EXCEEDING 0,5 BAR - DESIGN AND CONSTRUCTION |
| EN 1473:2016 | Installation and equipment for liquefied natural gas - Design of onshore installations |
| DD CEN/TS 14421:2006 | Hose tail and ferrule for crimping and swaging |
| 09/30205883 DC : 0 | BS EN 13709 - INDUSTRIAL VALVES - STEEL GLOBE AND GLOBE STOP AND CHECK VALVES |
| 14/30287821 DC : 0 | BS EN 13807 - TRANSPORTABLE GAS CYLINDERS - BATTERY VEHICLES - DESIGN, MANUFACTURE, IDENTIFICATION AND TESTING |
| PREN 10222-1 : DRAFT 2012 | STEEL FORGINGS FOR PRESSURE PURPOSES - PART 1: GENERAL REQUIREMENTS |
| PREN 13941 : DRAFT 2009 | DESIGN AND INSTALLATION OF REINSULATED BONDED PIPE SYSTEMS FOR DISTRICT HEATING |
| 14/30260020 DC : 0 | BS EN 12285-1 - WORKSHOP FABRICATED STEEL TANKS - PART 1: HORIZONTAL CYLINDRICAL SINGLE SKIN AND DOUBLE SKIN TANKS FOR THE UNDERGROUND STORAGE OF FLAMMABLE AND NONFLAMMABLE WATER POLLUTING LIQUIDS |
| SN EN ISO 15611 : 2004 | SPECIFICATION AND QUALIFICATION OF WELDING PROCEDURES FOR METALLIC MATERIALS - QUALIFICATION BASED ON PREVIOUS WELDING EXPERIENCE (ISO 15611:2003) |
| PREN 12285-1 : DRAFT 2016 | WORKSHOP FABRICATED STEEL TANKS - PART 1: HORIZONTAL CYLINDRICAL SINGLE SKIN AND DOUBLE SKIN TANKS FOR THE UNDERGROUND STORAGE OF FLAMMABLE AND NONFLAMMABLE WATER POLLUTING LIQUIDS OTHER THAN FOR HEATING AND COOLING OF BUILDINGS |
| UNI EN 10253-4 : 2009 | BUTT-WELDING PIPE FITTINGS - PART 4: WROUGHT AUSTENITIC AND AUSTENITIC-FERRITIC (DUPLEX) STAINLESS STEELS WITH SPECIFIC INSPECTION REQUIREMENTS |
| UNI EN ISO 15612 : 2006 | SPECIFICATION AND QUALIFICATION OF WELDING PROCEDURES FOR METALLIC MATERIALS - QUALIFICATION BY ADOPTION OF A STANDARD WELDING PROCEDURE |
| UNI EN 334 : 2009 | GAS PRESSURE REGULATORS FOR INLET PRESSURES UP TO 100 BAR |
| PREN 10210-2 : DRAFT 2016 | HOT FINISHED STRUCTURAL STEEL HOLLOW SECTIONS - PART 2: TECHNICAL DELIVERY CONDITIONS |
| PREN 287-1 : DRAFT 2010 | QUALIFICATION TEST OF WELDERS - FUSION WELDING - PART 1: STEELS |
| I.S. EN 16767:2016 | INDUSTRIAL VALVES - STEEL AND CAST IRON CHECK VALVES |
| I.S. EN 13110:2012 | LPG EQUIPMENT AND ACCESSORIES - TRANSPORTABLE REFILLABLE WELDED ALUMINIUM CYLINDERS FOR LIQUEFIED PETROLEUM GAS (LPG) - DESIGN AND CONSTRUCTION |
| UNI EN 1092-1 : 2013 | FLANGES AND THEIR JOINTS - CIRCULAR FLANGES FOR PIPES, VALVES, FITTINGS AND ACCESSORIES, PN DESIGNATED - PART 1: STEEL FLANGES |
| DIN EN 1092-1:2016-05 (Draft) | FLANGES AND THEIR JOINTS - CIRCULAR FLANGES FOR PIPES, VALVES, FITTINGS AND ACCESSORIES, PN DESIGNATED - PART 1: STEEL FLANGES |
| BS EN 14025 : 2013 | TANKS FOR THE TRANSPORT OF DANGEROUS GOODS - METALLIC PRESSURE TANKS - DESIGN AND CONSTRUCTION |
| EN 14025:2013+A1:2016 | Tanks for the transport of dangerous goods - Metallic pressure tanks - Design and construction |
| ISO 15612:2004 | Specification and qualification of welding procedures for metallic materials Qualification by adoption of a standard welding procedure |
| I.S. EN 1092-1:2007 | FLANGES AND THEIR JOINTS - CIRCULAR FLANGES FOR PIPES, VALVES,FITTINGS AND ACCESSORIES, PN DESIGNATED - PART 1: STEEL FLANGES |
| I.S. EN 14423:2013 | CLAMP TYPE COUPLING ASSEMBLIES FOR USE WITH STEAM HOSES RATED FOR PRESSURES UP TO 18 BAR |
| ISO 15609-2:2001 | Specification and qualification of welding procedures for metallic materials Welding procedure specification Part 2: Gas welding |
| DIN EN 13110:2012-07 | LPG EQUIPMENT AND ACCESSORIES - TRANSPORTABLE REFILLABLE WELDED ALUMINIUM CYLINDERS FOR LIQUEFIED PETROLEUM GAS (LPG) - DESIGN AND CONSTRUCTION |
| DIN EN ISO 15609-1:2005-01 | SPECIFICATION AND QUALIFICATION OF WELDING PROCEDURES FOR METALLIC MATERIALS - WELDING PROCEDURE SPECIFICATION - PART 1: ARC WELDING |
| DIN EN 287-1:2011-11 | QUALIFICATION TEST OF WELDERS - FUSION WELDING - PART 1: STEELS |
| DIN EN ISO 15609-3:2004-10 | Specification and qualification of welding procedures for metallic materials - Welding procedure specification - Part 3: Electron beam welding (ISO 15609-3:2004) |
| UNE-EN 10208-1:2011 | Steel pipes for pipelines for combustible fluids - Technical delivery conditions - Part 1: Pipes of requirement class A |
| DIN EN 14276-1:2011-05 | PRESSURE EQUIPMENT FOR REFRIGERATING SYSTEMS AND HEAT PUMPS - PART 1: VESSELS - GENERAL REQUIREMENTS |
| DIN EN 448:2016-02 | DISTRICT HEATING PIPES - PREINSULATED BONDED PIPE SYSTEMS FOR DIRECTLY BURIED HOT WATER NETWORKS - FITTING ASSEMBLIES OF STEEL SERVICE PIPES, POLYURETHANE THERMAL INSULATION AND OUTER CASING OF POLYETHYLENE |
| DIN EN 13807:2016-02 (Draft) | TRANSPORTABLE GAS CYLINDERS - BATTERY VEHICLES AND MULTIPLE-ELEMENT GAS CONTAINERS (MEGCS) - DESIGN, MANUFACTURE, IDENTIFICATION AND TESTING |
| DIN EN 14394:2008-12 | HEATING BOILERS - HEATING BOILERS WITH FORCED DRAUGHT BURNERS - NOMINAL HEAT OUTPUT NOT EXCEEDING 10 MW AND MAXIMUM OPERATING TEMPERATURE OF 110 DEGREE C |
| DIN EN 14382:2016-05 (Draft) | SAFETY DEVICES FOR GAS PRESSURE REGULATING STATIONS AND INSTALLATIONS - GAS SAFETY SHUT-OFF DEVICES FOR INLET PRESSURES UP TO 100 BAR |
| BS EN 15085-2:2007 | Railway applications. Welding of railway vehicles and components Quality requirements and certification of welding manufacturer |
| BS EN 10163-1:2004 | Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections General requirements |
| UNE-EN 764-4:2015 | Pressure equipment - Part 4: Establishment of technical delivery conditions for metallic materials |
| UNE-EN 13807:2017 | Transportable gas cylinders - Battery vehicles and multiple-element gas containers (MEGCs) - Design, manufacture, identification and testing |
| EN 14276-1:2020 | Pressure equipment for refrigerating systems and heat pumps - Part 1: Vessels - General requirements |
| UNI EN 14276-1 : 2011 | PRESSURE EQUIPMENT FOR REFRIGERATING SYSTEMS AND HEAT PUMPS - PART 1: VESSELS - GENERAL REQUIREMENTS |
| I.S. EN 15085-2:2007 | RAILWAY APPLICATIONS - WELDING OF RAILWAY VEHICLES AND COMPONENTS - PART 2: QUALITY REQUIREMENTS AND CERTIFICATION OF WELDING MANUFACTURER |
| UNE-EN 287-1:2011 | Qualification test of welders - Fusion welding - Part 1: Steels |
| EN 13094:2015 | Tanks for the transport of dangerous goods - Metallic tanks with a working pressure not exceeding 0,5 bar - Design and construction |
| I.S. EN 13094:2015 | TANKS FOR THE TRANSPORT OF DANGEROUS GOODS - METALLIC TANKS WITH A WORKING PRESSURE NOT EXCEEDING 0,5 BAR - DESIGN AND CONSTRUCTION |
| EN 15085-2:2007 | Railway applications - Welding of railway vehicles and components - Part 2: Quality requirements and certification of welding manufacturer |
| I.S. EN 489:2009 | DISTRICT HEATING PIPES - PREINSULATED BONDED PIPE SYSTEMS FOR DIRECTLY BURIED HOT WATER NETWORKS - JOINT ASSEMBLY FOR STEEL SERVICE PIPES, POLYURETHANE THERMAL INSULATION AND OUTER CASING OF POLYETHYLENE |
| EN ISO 15610:2003 | Specification and qualification of welding procedures for metallic materials - Qualification based on tested welding consumables (ISO 15610:2003) |
| EN ISO 15613:2004 | Specification and qualification of welding procedures for metallic materials - Qualification based on pre-production welding test (ISO 15613:2004) |
| UNI EN 489 : 2009 | DISTRICT HEATING PIPES - PREINSULATED BONDED PIPE SYSTEMS FOR DIRECTLY BURIED HOT WATER NETWORKS - JOINT ASSEMBLY FOR STEEL SERVICE PIPES, POLYURETHANE THERMAL INSULATION AND OUTER CASING OF POLYETHYLENE |
| UNI EN 13941 : 2011 | DESIGN AND INSTALLATION OF PREINSULATED BONDED PIPE SYSTEMS FOR DISTRICT HEATING |
| UNI EN ISO 15614-2 : 2006 | SPECIFICATION AND QUALIFICATION OF WELDING PROCEDURES FOR METALLIC MATERIALS - WELDING PROCEDURE TEST - PART 2: ARC WELDING OF ALUMINIUM AND ITS ALLOYS |
| UNI EN 14394 : 2008 | HEATING BOILERS - HEATING BOILERS WITH FORCED DRAUGHT BURNERS - NOMINAL HEAT OUTPUT NOT EXCEEDING 10 MW AND MAXIMUM OPERATING TEMPERATURE OF 110 DEGREES C |
| UNI EN 10219-1 : 2006 | COLD FORMED WELDED STRUCTURAL HOLLOW SECTIONS OF NON-ALLOY AND FINE GRAIN STEELS - PART 1: TECHNICAL DELIVERY CONDITIONS |
| UNI EN 10208-1 : 2009 | STEEL PIPES FOR PIPELINES FOR COMBUSTIBLE FLUIDS - TECHNICAL DELIVERY CONDITIONS - PART 1: PIPES OF REQUIREMENT CLASS A |
| UNI EN 12496 : 2013 | GALVANIC ANODES FOR CATHODIC PROTECTION IN SEAWATER AND SALINE MUD |
| UNI EN 1775 : 2007 | GAS SUPPLY - GAS PIPEWORK FOR BUILDINGS - MAXIMUM OPERATING PRESSURE LESS THAN OR EQUAL TO 5 BAR - FUNCTIONAL RECOMMENDATIONS |
| UNI EN 15001-1 : 2009 | GAS INFRASTRUCTURE - GAS INSTALLATION PIPEWORK WITH AN OPERATING PRESSURE GREATER THAN 0,5 BAR FOR INDUSTRIAL INSTALLATIONS AND GREATER THAN 5 BAR FOR INDUSTRIAL AND NON-INDUSTRIAL INSTALLATIONS - PART 1: DETAILED FUNCTIONAL REQUIREMENTS FOR DESIGN, MATERIALS, CONSTRUCTION, INSPECTION AND TESTING |
| UNI EN 14382 : 2009 | SAFETY DEVICES FOR GAS PRESSURE REGULATING STATIONS AND INSTALLATIONS - GAS SAFETY SHUT-OFF DEVICES FOR INLET PRESSURES UP TO 100 BAR |
| UNI EN ISO 9606-2 : 2006 | Qualification test of welders - Fusion welding - Part 1: Aluminium and aluminium alloys |
| UNI EN 1011-1 : 2009 | WELDING - RECOMMENDATIONS FOR WELDING OF METALLIC MATERIALS - PART 1: GENERAL GUIDANCE FOR ARC WELDING |
| I.S. EN ISO 15614-4:2005 | SPECIFICATION AND QUALIFICATION OF WELDING PROCEDURES FOR METALLIC MATERIALS - WELDING PROCEDURE TEST - PART 4: FINISHING WELDING OF ALUMINIUM CASTINGS |
| UNI EN 287-1 : 2012 | QUALIFICATION TEST OF WELDERS - FUSION WELDING - PART 1: STEELS |
| UNI EN 1984 : 2010 | INDUSTRIAL VALVES - STEEL GATE VALVES |
| UNI EN 13709 : 2010 | INDUSTRIAL VALVES - STEEL GLOBE AND GLOBE STOP AND CHECK VALVES |
| UNI EN 15594 : 2009 | RAILWAY APPLICATIONS - TRACK - RESTORATION OF RAILS BY ELECTRIC ARC WELDING |
| 04/19989519 DC : DRAFT AUG 2004 | BS EN ISO 15614-7 - SPECIFICATION AND QUALIFICATION OF WELDING PROCEDURES FOR METALLIC MATERIALS - WELDING PROCEDURE TEST - PART 7: OVERLAY WELDING |
| BS EN 16725:2016 | Railway applications. Track. Restoration and repair of manganese crossings |
| 16/30336440 DC : DRAFT MAR 2016 | BS EN 1092-1 - FLANGES AND THEIR JOINTS - CIRCULAR FLANGES FOR PIPES, VALVES, FITTINGS AND ACCESSORIES, PN DESIGNATED - PART 1: STEEL FLANGES |
| PREN 13807 : DRAFT 2014 | TRANSPORTABLE GAS CYLINDERS - BATTERY VEHICLES - DESIGN, MANUFACTURE, IDENTIFICATION AND TESTING |
| 08/30182454 DC : DRAFT JULY 2008 | BS EN 10208-1 - STEEL PIPES FOR PIPELINES FOR COMBUSTIBLE FLUIDS - TECHNICAL DELIVERY CONDITIONS - PART 1: PIPES OF REQUIREMENT CLASS A |
| I.S. EN ISO 15610:2004 | SPECIFICATION AND QUALIFICATION OF WELDING PROCEDURES FOR METALLIC MATERIALS - QUALIFICATION BASED ON TESTED WELDING CONSUMABLES |
| BS EN 12496:2013 | Galvanic anodes for cathodic protection in seawater and saline mud |
| 16/30339483 DC : 0 | BS EN 593 - INDUSTRIAL VALVES - METALLIC BUTTERFLY VALVES FOR GENERAL PURPOSES |
| 08/30181449 DC : DRAFT JULY 2008 | BS EN 1069-2 - WATER SLIDES - PART 2: INSTRUCTIONS |
| 12/30257022 DC : 0 | BS EN 13611 - SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS OR LIQUID FUELS - GENERAL REQUIREMENTS |
| 15/30325364 DC : 0 | BS EN 1069-2 - WATER SLIDES - PART 2: INSTRUCTIONS |
| 17/30351224 DC : 0 | BS EN 14276-1 - PRESSURE EQUIPMENT FOR REFRIGERATING SYSTEMS AND HEAT PUMPS - PART 1: VESSELS - GENERAL REQUIREMENTS |
| DIN EN 10210-1:2016-01 (Draft) | Hot finished structural steel hollow sections - Part 1: General; German and English version prEN 10210-1:2016 |
| PREN 593 : DRAFT 2016 | INDUSTRIAL VALVES - METALLIC BUTTERFLY VALVES FOR GENERAL PURPOSES |
| PREN 12972 : DRAFT 2017 | TANKS FOR TRANSPORT OF DANGEROUS GOODS - TESTING, INSPECTION AND MARKING OF METALLIC TANKS |
| 07/30165568 DC : 0 | BS EN 448 - DISTRICT HEATING PIPES - PREINSULATED BONDED PIPE SYSTEMS FOR DIRECTLY BURIED HOT WATER NETWORKS - FITTING ASSEMBLIES OF STEEL SERVICE PIPES, POLYURETHANE THERMAL INSULATION AND OUTER CASING OF POLYETHYLENE |
| BS EN 10253-4:2008 | Butt-welding pipe fittings Wrought austenitic and austenitic-ferritic (duplex) stainless steels with specific inspection requirements |
| I.S. EN 334:2005 | GAS PRESSURE REGULATORS FOR INLET PRESSURES UP TO 100 BAR |
| 03/115441 DC : DRAFT OCT 2003 | BS EN ISO 15614-6 - SPECIFICATION AND QUALIFICATION OF WELDING PROCEDURES FOR METALLIC MATERIALS - WELDING PROCEDURE TEST - ARC WELDING OF COPPER AND ITS ALLOYS |
| I.S. EN 12693:2008 | REFRIGERATING SYSTEMS AND HEAT PUMPS - SAFETY AND ENVIRONMENTAL REQUIREMENTS - POSITIVE DISPLACEMENT REFRIGERANT COMPRESSORS |
| EN 1092-1:2018 | Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 1: Steel flanges |
| 17/30360691 DC : 0 | BS EN 12972 - TANKS FOR TRANSPORT OF DANGEROUS GOODS - TESTING, INSPECTION AND MARKING OF METALLIC TANKS |
| DIN EN 13611:2016-09 | SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS AND/OR LIQUID FUELS - GENERAL REQUIREMENTS |
| PREN 13611 : DRAFT 2017 | SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS AND/OR LIQUID FUELS - GENERAL REQUIREMENTS |
| DIN EN 12693:2016-10 (Draft) | REFRIGERATING SYSTEMS AND HEAT PUMPS - SAFETY AND ENVIRONMENTAL REQUIREMENTS - POSITIVE DISPLACEMENT REFRIGERANT COMPRESSORS |
| UNE-EN 14423:2014 | Clamp type coupling assemblies for use with steam hoses rated for pressures up to 18 bar |
| EN ISO 15612:2004 | Specification and qualification of welding procedures for metallic materials - Qualification by adoption of a standard welding procedure (ISO 15612:2004) |
| EN 12480:2018 | Gas meters - Rotary displacement gas meters |
| I.S. CEN TS 14421:2006 | HOSE TAIL AND FERRULE FOR CRIMPING AND SWAGING |
| I.S. EN 12480:2018 | GAS METERS - ROTARY DISPLACEMENT GAS METERS |
| DIN EN 13094:2015-07 | TANKS FOR THE TRANSPORT OF DANGEROUS GOODS - METALLIC TANKS WITH A WORKING PRESSURE NOT EXCEEDING 0,5 BAR - DESIGN AND CONSTRUCTION |
| DIN EN 14015:2005-02 | Specification for the design and manufacture of site built, vertical, cylindrical, flat-bottomed, above ground, welded, steel tanks for the storage of liquids at ambient temperature and above |
| DIN EN 14208:2004-05 | Transportable gas cylinders - Specification for welded pressure drums up to 1000 litre capacity for the transport of gases - Design and construction |
| DIN EN 10219-1:2016-01 (Draft) | Cold formed welded structural steel hollow sections - Part 1: General; German and English version prEN 10219-1:2016 |
| DIN EN 489:2009-07 | District heating pipes - Preinsulated bonded pipe systems for directly buried hot water networks - Joint assembly for steel service pipes, polyurethane thermal insulation and outer casing of polyethylene; German and English version EN 489:2009 |
| BS EN 14394 : 2005 | HEATING BOILERS - HEATING BOILERS WITH FORCED DRAUGHT BURNERS - NOMINAL HEAT OUTPUT NOT EXCEEDING 10 MW AND MAXIMUM OPERATING TEMPERATURE OF 110 DEGREE C |
| BS EN 1069-2:2017 | Water slides Instructions |
| BS EN 14341:2006 | Industrial valves. Steel check valves |
| BS EN ISO 15613:2004 | Specification and qualification of welding procedures for metallic materials. Qualification based on pre-production welding test |
| EN 16767:2016 | Industrial valves - Steel and cast iron check valves |
| BS EN 14620-2:2006 | Design and manufacture of site built, vertical, cylindrical, flat-bottomed steel tanks for the storage of refrigerated, liquefied gases with operating temperatures between 0°C and -165°C Metallic components |
| UNE-EN 15001-1:2010 | Gas Infrastructure - Gas installation pipework with an operating pressure greater than 0,5 bar for industrial installations and greater than 5 bar for industrial and non-industrial installations - Part 1: Detailed functional requirements for design, materials, construction, inspection and testing |
| BS EN ISO 9606-2:2004 | Qualification test of welders. Fusion welding Aluminium and aluminium alloys |
| BS EN 10311:2005 | Joints for the connection of steel tubes and fittings for the conveyance of water and other aqueous liquids |
| BS EN 764-4:2014 | Pressure equipment Establishment of technical delivery conditions for metallic materials |
| BS EN 14638-1:2006 | Transportable gas cylinders. Refillable welded receptacles of a capacity not exceeding 150 litres Welded austenitic stainless steel cylinders made to a design justified by experimental methods |
| UNE-EN 12496:2013 | Galvanic anodes for cathodic protection in seawater and saline mud |
| BS EN ISO 15610:2003 | Specification and qualification of welding procedures for metallic materials. Qualification based on tested welding consumables |
| ISO 15613:2004 | Specification and qualification of welding procedures for metallic materials Qualification based on pre-production welding test |
| BS EN 1011-1:2009 | Welding. Recommendations for welding of metallic materials General guidance for arc welding |
| BS EN ISO 15614-2:2005 | Specification and qualification of welding procedures for metallic materials. Welding procedure test Arc welding of aluminium and its alloys |
| UNE-EN 13110:2012 | LPG equipment and accessories - Transportable refillable welded aluminium cylinders for liquefied petroleum gas (LPG) - Design and construction |
| EN 14276-1:2006+A1:2011 | Pressure equipment for refrigerating systems and heat pumps - Part 1: Vessels - General requirements |
| UNE-EN 13094:2015 | Tanks for the transport of dangerous goods - Metallic tanks with a working pressure not exceeding 0,5 bar - Design and construction |
| BS EN 14276-1 : 2006 | PRESSURE EQUIPMENT FOR REFRIGERATING SYSTEMS AND HEAT PUMPS - PART 1: VESSELS - GENERAL REQUIREMENTS |
| UNE-EN 14025:2014 | Tanks for the transport of dangerous goods - Metallic pressure tanks - Design and construction |
| ISO 15611:2003 | Specification and qualification of welding procedures for metallic materials — Qualification based on previous welding experience |
| BS EN 1759-1:2004 | Flanges and their joints. Circular flanges for pipes, valves, fittings and accessories, class-designated Steel flanges, NPS 1/2 to 24 |
| ISO 15609-1:2004 | Specification and qualification of welding procedures for metallic materials Welding procedure specification Part 1: Arc welding |
| BS EN 12732 : 2013 | GAS INFRASTRUCTURE - WELDING STEEL PIPEWORK - FUNCTIONAL REQUIREMENTS |
| UNE-EN 12732:2014+A1:2014 | Gas infrastructure - Welding steel pipework - Functional requirements |
| UNE-EN 13110:2012+A1:2017 | LPG equipment and accessories - Transportable refillable welded aluminium cylinders for liquefied petroleum gas (LPG) - Design and construction |
| UNE-EN 448:2017 | District heating pipes - Preinsulated bonded pipe systems for directly buried hot water networks - Fitting assemblies of steel service pipes, polyurethane thermal insulation and outer casing of polyethylene |
| BS EN 13941 : 2009 | DESIGN AND INSTALLATION OF PREINSULATED BONDED PIPE SYSTEMS FOR DISTRICT HEATING |
| BS EN 13084-1:2007 | Free-standing chimneys General requirements |
| DIN EN ISO 15610:2004-02 | Specification and qualification of welding procedures for metallic materials - Qualification based on tested welding consumables (ISO 15610:2003) |
| EN 15594:2009 | Railway applications - Track - Restoration of rails by electric arc welding |
| EN 1775:2007 | Gas supply - Gas pipework for buildings - Maximum operating pressure less than or equal to 5 bar - Functional recommendations |
| EN 14394:2005+A1:2008 | Heating boilers - Heating boilers with forced draught burners - Nominal heat output not exceeding 10 MW and maximum operating temperature of 110 °C |
| EN 15001-1:2009 | Gas Infrastructure - Gas installation pipework with an operating pressure greater than 0,5 bar for industrial installations and greater than 5 bar for industrial and non-industrial installations - Part 1: Detailed functional requirements for design, materials, construction, inspection and testing |
| EN 13709:2010 | Industrial valves - Steel globe and globe stop and check valves |
| EN 14638-1:2006 | Transportable gas cylinders - Refillable welded receptacles of a capacity not exceeding 150 litres - Part 1: Welded austenitic stainless steel cylinders made to a design justified by experimental methods |
| EN 287-1:2011 | Qualification test of welders - Fusion welding - Part 1: Steels |
| EN 489:2009 | District heating pipes - Preinsulated bonded pipe systems for directly buried hot water networks - Joint assembly for steel service pipes, polyurethane thermal insulation and outer casing of polyethylene |
| EN 13941:2009+A1:2010 | Design and installation of preinsulated bonded pipe systems for district heating |
| EN 14015:2004 | Specification for the design and manufacture of site built, vertical, cylindrical, flat-bottomed, above ground, welded, steel tanks for the storage of liquids at ambient temperature and above |
| EN 1759-1:2004 | Flanges and their joint - Circular flanges for pipes, valves, fittings and accessories, Class designated - Part 1: Steel flanges, NPS 1/2 to 24 |
| EN 14620-2:2006 | Design and manufacture of site built, vertical, cylindrical, flat-bottomed steel tanks for the storage of refrigerated, liquefied gases with operating temperatures between 0 °C and -165 °C - Part 2: Metallic components |
| EN ISO 15614-2:2005 | Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 2: Arc welding of aluminium and its alloys (ISO 15614-2:2005) |
| EN 16725:2016 | Railway applications - Track - Restoration and repair of manganese crossings |
| EN 1984:2010 | Industrial valves - Steel gate valves |
| EN ISO 15609-3:2004 | Specification and qualification of welding procedures for metallic materials - Welding procedures specification - Part 3: Electron beam welding (ISO 15609-3:2004) |
| EN ISO 15609-1:2004 | Specification and qualification of welding procedures for metallic materials - Welding procedure specification - Part 1: Arc welding (ISO 15609-1:2004) |
| EN ISO 9606-2:2004 | Qualification test of welders - Fusion welding - Part 2: Aluminium and aluminium alloys (ISO 9606-2:2004) |
| EN 334:2005+A1:2009 | Gas pressure regulators for inlet pressures up to 100 bar |
| EN 448:2015 | District heating pipes - Preinsulated bonded pipe systems for directly buried hot water networks - Fitting assemblies of steel service pipes, polyurethane thermal insulation and outer casing of polyethylene |
| EN 593:2017 | Industrial valves - Metallic butterfly valves for general purposes |
| EN ISO 15611:2003 | Specification and qualification of welding procedures for metallic materials - Qualification based on previous welding experience (ISO 15611:2003) |
| EN 14208:2004 | Transportable gas cylinders - Specification for welded pressure drums up to 1000 litre capacity for the transport of gases - Design and construction |
| EN 14341:2006 | Industrial valves - Steel check valves |
| EN 13807:2017 | Transportable gas cylinders - Battery vehicles and multiple-element gas containers (MEGCs) - Design, manufacture, identification and testing |
| EN 764-4:2014 | Pressure equipment - Part 4: Establishment of technical delivery conditions for metallic materials |
| I.S. EN 10208-1:2009 | STEEL PIPES FOR PIPELINES FOR COMBUSTIBLE FLUIDS - TECHNICAL DELIVERY CONDITIONS - PART 1: PIPES OF REQUIREMENT CLASS A |
| 10/30235392 DC : 0 | BS EN 287-1 - QUALIFICATION TEST OF WELDERS - FUSION WELDING - PART 1: STEELS |
| UNE-EN 16725:2017 | Railway applications - Track - Restoration and repair of manganese crossings |
| PREN ISO 15614-6 : DRAFT 2003 | SPECIFICATION AND QUALIFICATION OF WELDING PROCEDURES FOR METALLIC MATERIALS - WELDING PROCEDURE TEST - PART 6: ARC WELDING OF COPPER AND ITS ALLOYS |
| 08/30187521 DC : 0 | BS EN 593 - INDUSTRIAL VALVES - METALLIC BUTTERFLY VALVES |
| I.S. EN ISO 9606-2:2005 | QUALIFICATION TEST OF WELDERS - FUSION WELDING - PART 2: ALUMINIUM AND ALUMINIUM ALLOYS |
| BS EN 15001-1:2009 | Gas infrastructure. Gas installation pipework with an operating pressure greater than 0,5 bar for industrial installations and greater than 5 bar for industrial and non-industrial installations Detailed functional requirements for design, materials, construction, inspection and testing |
| DIN EN 16767:2016-08 | INDUSTRIAL VALVES - STEEL AND CAST IRON CHECK VALVES |
| 12/30259217 DC : 0 | BS EN 12972 - TANKS FOR TRANSPORT OF DANGEROUS GOODS - TESTING, INSPECTION AND MARKING OF METALLIC TANKS |
| BS EN ISO 15612:2004 | Specification and qualification of welding procedures for metallic materials. Qualification by adoption of a standard welding procedure |
| 14/30297213 DC : 0 | BS EN 1473 - INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN OF ONSHORE INSTALLATIONS |
| EN 12079-1:2006 | Offshore containers and associated lifting sets - Part 1: Offshore container - Design, manufacture and marking |
| PREN 10219-2 : DRAFT 2016 | COLD FORMED WELDED STRUCTURAL STEEL HOLLOW SECTIONS - PART 2: TECHNICAL DELIVERY CONDITIONS |
| UNE-EN 15594:2010 | Railway applications - Track - Restoration of rails by electric arc welding |
| PREN 14276-1 : DRAFT 2017 | PRESSURE EQUIPMENT FOR REFRIGERATING SYSTEMS AND HEAT PUMPS - PART 1: VESSELS - GENERAL REQUIREMENTS |
| I.S. EN 1090-1:2009 | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 1: REQUIREMENTS FOR CONFORMITY ASSESSMENT OF STRUCTURAL COMPONENTS |
| I.S. EN 15594:2009 | RAILWAY APPLICATIONS - TRACK - RESTORATION OF RAILS BY ELECTRIC ARC WELDING |
| I.S. EN 12496:2013 | GALVANIC ANODES FOR CATHODIC PROTECTION IN SEAWATER AND SALINE MUD |
| 18/30368651 DC : 0 | BS EN 448 - DISTRICT HEATING PIPES - BONDED SINGLE PIPE SYSTEMS FOR DIRECTLY BURIED HOT WATER NETWORKS - FACTORY MADE FITTING ASSEMBLIES OF STEEL SERVICE PIPES, POLYURETHANE THERMAL INSULATION AND A CASING OF POLYETHYLENE |
| I.S. EN 14025:2013 | TANKS FOR THE TRANSPORT OF DANGEROUS GOODS - METALLIC PRESSURE TANKS - DESIGN AND CONSTRUCTION |
| I.S. EN 10253-4:2008 | BUTT-WELDING PIPE FITTINGS - PART 4: WROUGHT AUSTENITIC AND AUSTENITIC-FERRITIC (DUPLEX) STAINLESS STEELS WITH SPECIFIC INSPECTION REQUIREMENTS |
| 16/30332614 DC : 0 | BS EN 10219-2 - COLD FORMED WELDED STRUCTURAL STEEL HOLLOW SECTIONS - PART 2: TECHNICAL DELIVERY CONDITIONS |
| UNE-EN 13611:2016 | Safety and control devices for burners and appliances burning gaseous and/or liquid fuels - General requirements |
| BS EN 14423:2013+A2:2019 | Clamp type coupling assemblies for use with steam hoses rated for pressures up to 18 bar |
| BS EN 448:2015 | District heating pipes. Preinsulated bonded pipe systems for directly buried hot water networks. Fitting assemblies of steel service pipes, polyurethane thermal insulation and outer casing of polyethylene |
| DIN EN 764-4:2015-03 | PRESSURE EQUIPMENT - PART 4: ESTABLISHMENT OF TECHNICAL DELIVERY CONDITIONS FOR METALLIC MATERIALS |
| DIN EN ISO 9606-2:2005-03 | Qualification test of welders - Fusion welding - Part 2: Aluminium and aluminium alloys (ISO 9606-2:2004); German version EN ISO 9606-2:2004 |
| DIN EN 1069-2:2015-09 (Draft) | WATER SLIDES - PART 2: INSTRUCTIONS |
| BS EN 1775:2007 | Gas supply. Gas pipework for buildings. Maximum operating pressure less than or equal to 5 bar. Functional recommendations |
| BS EN ISO 15609-1:2004 | Specification and qualification of welding procedures for metallic materials. Welding procedure specification Arc welding |
| BS EN 12079-1:2006 | Offshore containers and associated lifting sets Offshore containers. Design, manufacture and marking |
| ISO 9606-2:2004 | Qualification test of welders — Fusion welding — Part 2: Aluminium and aluminium alloys |
| BS EN 10208-1:2009 | Steel pipes for pipelines for combustible fluids. Technical delivery conditions Pipes of requirement class A |
| BS EN 10210-1:2006 | Hot finished structural hollow sections of non-alloy and fine grain steels Technical delivery requirements |
| BS EN 1825-1:2004 | Grease separators Principles of design, performance and testing, marking and quality control |
| ISO 15610:2003 | Specification and qualification of welding procedures for metallic materials — Qualification based on tested welding consumables |
| UNE-EN 10222-1:2017 | Steel forgings for pressure purposes - Part 1: General requirements for open die forgings |
| BS EN 10222-1:2017 | Steel forgings for pressure purposes General requirements for open die forgings |
| BS EN ISO 15611:2003 | Specification and qualification of welding procedures for metallic materials. Qualification based on previous welding experience |
| BS EN 13094:2015 | Tanks for the transport of dangerous goods. Metallic tanks with a working pressure not exceeding 0,5 bar. Design and construction |
| BS EN 10219-1:2006 | Cold formed welded structural hollow sections of non-alloy and fine grain steels Technical delivery requirements |
| BS EN 12285-2:2005 | Workshop fabricated steel tanks Horizontal cylindrical single skin and double skin tanks for the aboveground storage of flammable and non-flammable water polluting liquids |
| BS EN 13110 : 2012 | LPG EQUIPMENT AND ACCESSORIES - TRANSPORTABLE REFILLABLE WELDED ALUMINIUM CYLINDERS FOR LIQUEFIED PETROLEUM GAS (LPG) - DESIGN AND CONSTRUCTION |
| DIN EN 12693:2008-09 | REFRIGERATING SYSTEMS AND HEAT PUMPS - SAFETY AND ENVIRONMENTAL REQUIREMENTS - POSITIVE DISPLACEMENT REFRIGERANT COMPRESSORS |
| CEN/TS 14421:2006 | Hose tail and ferrule for crimping and swaging |
| I.S. EN 13611:2015/AC:2016 | SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS AND/OR LIQUID FUELS - GENERAL REQUIREMENTS |
| DIN EN 10311:2005-08 | Joints for the connection of steel tubes and fittings for the conveyance of water and other aqueous liquids |
| DIN EN 13807:2017-05 | TRANSPORTABLE GAS CYLINDERS - BATTERY VEHICLES AND MULTIPLE-ELEMENT GAS CONTAINERS (MEGCS) - DESIGN, MANUFACTURE, IDENTIFICATION AND TESTING |
| EN 13084-1:2007 | Free-standing chimneys - Part 1: General requirements |
| DIN EN 10219-1:2006-07 | Cold formed welded structural hollow sections of non-alloy and fine grain steels - Part 1: Technical delivery conditions |
| DIN EN 1090-1:2012-02 | Execution of steel structures and aluminium structures - Part 1: Requirements for conformity assessment of structural components (includes Amendment A1:2011) |
| DIN EN ISO 15613:2004-09 | Specification and qualification of welding procedures for metallic materials - Qualification based on pre-production welding test (ISO 15613:2004) |
| DIN EN 287-1:2004-05 | QUALIFICATION TEST OF WELDERS - FUSION WELDING - PART 1: STEELS |
| EN 12732:2013+A1:2014 | Gas infrastructure - Welding steel pipework - Functional requirements |
| DIN EN 1825-1:2004-12 | Grease separators - Part 1: Principles of design, performance and testing, marking and quality control; German version EN 1825-1:2004 |
| DIN EN 14638-1:2006-07 | Transportable gas cylinders - Refillable welded receptacles of a capacity not exceeding 150 litres - Part 1: Welded austenitic stainless steel cylinders made to a design justified by experimental methods |
| DIN EN ISO 15611:2004-03 | Specification and qualification of welding procedures for metallic materials - Qualification based on previous welding experience (ISO 15611:2003) |
| UNE-EN 12732:2014 | Gas infrastructure - Welding steel pipework - Functional requirements |
| UNE-EN 14276-1:2007 | Pressure equipment for refrigerating systems and heat pumps - Part 1: Vessels - General requirements |
| EN ISO 6520-1:2007 | Welding and allied processes - Classification of geometric imperfections in metallic materials - Part 1: Fusion welding (ISO 6520-1:2007) |
| EN ISO 15614-11:2002 | Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 11: Electron and laser beam welding (ISO 15614-11:2002) |
| ISO 9606-2:2004 | Qualification test of welders — Fusion welding — Part 2: Aluminium and aluminium alloys |
| EN ISO 15613:2004 | Specification and qualification of welding procedures for metallic materials - Qualification based on pre-production welding test (ISO 15613:2004) |
| EN ISO 6520-2:2013 | Welding and allied processes - Classification of geometric imperfections in metallic materials - Part 2: Welding with pressure (ISO 6520-2:2013) |
| EN ISO 15620:2000 | Welding - Friction welding of metallic materials (ISO 15620:2000) |
| ISO 14732:2013 | Welding personnel Qualification testing of welding operators and weld setters for mechanized and automatic welding of metallic materials |
| EN ISO 4063:2010 | Welding and allied processes - Nomenclature of processes and reference numbers (ISO 4063:2009, Corrected version 2010-03-01) |
| ISO 9606-1:2012 | Qualification testing of welders — Fusion welding — Part 1: Steels |
| EN ISO 9606-4:1999 | Approval testing of welders - Fusion welding - Part 4: Nickel and nickel alloys (ISO 9606-4:1999) |
| EN ISO 15611:2003 | Specification and qualification of welding procedures for metallic materials - Qualification based on previous welding experience (ISO 15611:2003) |
| EN 287-2:1992/A1:1997 | APPROVAL TESTING OF WELDERS - FUSION WELDING - ALUMINIUM AND ALUMINIUM ALLOYS |
| PREN ISO 15614-6 : DRAFT 2003 | SPECIFICATION AND QUALIFICATION OF WELDING PROCEDURES FOR METALLIC MATERIALS - WELDING PROCEDURE TEST - PART 6: ARC WELDING OF COPPER AND ITS ALLOYS |
| ISO 857-1:1998 | Welding and allied processes Vocabulary Part 1: Metal welding processes |
| EN ISO 9606-5:2000 | Approval testing of welders - Fusion welding - Part 5: Titanium and titanium alloys, zirconium and zirconium alloys (ISO 9606-5:2000) |
| PREN ISO 15614-13 : DRAFT 2010 | SPECIFICATION AND QUALIFICATION OF WELDING PROCEDURES FOR METALLIC MATERIALS - WELDING PROCEDURE TEST - PART 13: RESISTANCE BUTT (UPSET) AND FLASH WELDING |
| EN ISO 15614-8:2016 | Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 8: Welding of tubes to tube-plate joints (ISO 15614-8:2016) |
| EN ISO 14555:2017 | Welding - Arc stud welding of metallic materials (ISO 14555:2017) |
| EN ISO 15610:2003 | Specification and qualification of welding procedures for metallic materials - Qualification based on tested welding consumables (ISO 15610:2003) |
| EN 1418:1997 | Welding personnel - Approval testing of welding operators for fusion welding and resistance weld setters for fully mechanized and automatic welding of metallic materials |
| EN ISO 9606-3:1999 | Approval testing of welders - Fusion welding - Part 3: Copper and copper alloys (ISO 9606-3:1999) |
| EN 287-1:2011 | Qualification test of welders - Fusion welding - Part 1: Steels |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.