EN 60079-6:2015
Current
Current
The latest, up-to-date edition.
Explosive atmospheres - Part 6: Equipment protection by liquid immersion "o"
Published date
12-11-2015
Sorry this product is not available in your region.
FOREWORD
1 Scope
2 Normative references
3 Terms and definitions
4 Constructional requirements
5 Protective Liquid
6 Verifications and tests
7 Marking
8 Instructions
Annex A (normative) - Selection and erection requirements
Annex B (normative) - Maintenance requirements
Annex C (normative) - Repair and Overhaul requirements
Bibliography
Annex ZA (normative) - Normative references to international
Publications with their corresponding
European publications
Annex ZZ (informative) - Relationship between this European
standard and the essential requirements of
Directive 94/9/EC aimed to be covered
IEC 60079-6:2015 specifies the requirements for the design, construction, testing and marking of Ex Equipment and Ex Components with type of protection liquid immersion "o" intended for use in explosive gas atmospheres. Ex Equipment and Ex Components of type of protection liquid immersion "o" are either:- Level of Protection "ob" (EPL "Mb" or "Gb") or- Level of Protection "oc" (EPL "Gc"). For Level of Protection "ob", this standard applies where the rated voltage does not exceed 11 kV r.m.s. a.c. or d.c. For Level of Protection "oc", this standard applies where the rated voltage does not exceed 15 kV r.m.s. a.c. or d.c. This standard supplements and modifies the general requirements of IEC 60079-0. Where a requirement of this standard conflicts with a requirement of IEC 60079-0, the requirement of this standard takes precedence. This fourth edition cancels and replaces the third edition, published in 2007. This edition constitutes a technical revision. The significant changes with respect to the previous edition are:- Edition 4 represents a major technical revision of the requirements for oil immersion "o" and should be considered as introducing all new requirements. The normal "Table of Significant Changes" has not been included for this reason. In particular:- The requirements for oil immersion "o" have been redefined into liquid immersion, levels of protection "ob" and "oc" as recommended by the responses to 31/715/DC;- The ability to protect sparking contacts has been added to both "ob" and "oc". Additional requirements have been introduced for the protective liquid. Keywords: Ex Equipment and Ex Components with type of protection liquid immersion "o"
| Committee |
CLC/TC 31
|
| DevelopmentNote |
Supersedes EN 50015. (05/2007) To be read in conjunction with EN 60079-0. (06/2007)
|
| DocumentType |
Standard
|
| PublisherName |
European Committee for Standards - Electrical
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| NF EN 60079-6 : 2016 | Identical |
| BS EN 60079-6:2007 | Identical |
| UNE-EN 60079-6:2016 | Identical |
| CEI EN 60079-6 : 2016 | Identical |
| NBN EN 60079-6 : 2016 | Identical |
| I.S. EN 60079-6:2015 | Identical |
| NEN EN IEC 60079-6 : 2015 | Identical |
| IEC 60079-6:2015 | Identical |
| DIN EN 60079-6 : 2016 | Identical |
| PN-EN 60079-6:2016-02 | Identical |
| VDE 0170-2 : 2016 | Identical |
| SN EN 60079-6:2015 | Identical |
| BS EN 60079-6:2015 | Identical |
| UNI EN 1474-1 : 2009 | INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN AND TESTING OF MARINE TRANSFER SYSTEMS - PART 1: DESIGN AND TESTING OF TRANSFER ARMS |
| PREN 1127-1 : DRAFT 2017 | EXPLOSIVE ATMOSPHERES - EXPLOSION PREVENTION AND PROTECTION - PART 1: BASIC CONCEPTS AND METHODOLOGY |
| 09/30198043 DC : 0 | BS EN 1127-1 - EXPLOSIVE ATMOSPHERES - EXPLOSION PREVENTION AND PROTECTION - PART 1: BASIC CONCEPTS AND METHODOLOGY |
| NF EN 12405-1 : 2005 + A2 2010 | GAS METERS - CONVERSION DEVICES - PART 1: VOLUME CONVERSION |
| UNE-EN 12405-1:2006 | Gas meters - Conversion devices - Part 1: Volume conversion |
| S.R. CEN/TR 16787:2014 | INDUSTRIAL GAS INSTALLATION - GUIDELINE |
| 16/30341165 DC : 0 | BS EN 14492-2 - CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 2: POWER DRIVEN HOISTS |
| 17/30365866 DC : 0 | BS EN 1127-1 - EXPLOSIVE ATMOSPHERES - EXPLOSION PREVENTION AND PROTECTION - PART 1: BASIC CONCEPTS AND METHODOLOGY |
| 18/30369304 DC : DRAFT APR 2018 | BS EN 1473 - INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN OF ONSHORE INSTALLATIONS |
| DIN EN 1473:2016-10 | Installation and equipment for liquefied natural gas - Design of onshore installations |
| UNE-EN 1127-1:2012 | Explosive atmospheres - Explosion prevention and protection - Part 1: Basic concepts and methodology |
| BS EN 60079-18 : 2015 | EXPLOSIVE ATMOSPHERES - PART 18: EQUIPMENT PROTECTION BY ENCAPSULATION 'M' |
| DIN EN 1127-2:2002-07 | EXPLOSIVE ATMOSPHERES - EXPLOSION PREVENTION AND PROTECTION - PART 2: BASIC CONCEPTS AND METHODOLOGY FOR MINING |
| DIN EN 13922:2011-11 | TANKS FOR TRANSPORT OF DANGEROUS GOODS - SERVICE EQUIPMENT FOR TANKS - OVERFILL PREVENTION SYSTEMS FOR LIQUID FUELS |
| DIN EN 12312-5:2009-08 | Aircraft ground support equipment - Specific requirements - Part 5: Aircraft fuelling equipment (includes Amendment A1:2009) |
| EN 1010-1:2004+A1:2010 | Safety of machinery - Safety requirements for the design and construction of printing and paper converting machines - Part 1: Common requirements |
| EN 12621:2006+A1:2010 | Machinery for the supply and circulation of coating materials under pressure - Safety requirements |
| PREN 12405-1 : DRAFT 2017 | GAS METERS - CONVERSION DEVICES - PART 1: VOLUME CONVERSION |
| CEN/TR 16787:2014 | Industrial Gas Installation - Guideline |
| 08/30180312 DC : DRAFT MAR 2008 | BS EN 50223 - STATIONARY ELECTROSTATIC APPLICATION EQUIPMENT FOR IGNITABLE FLOCK MATERIAL - SAFETY REQUIREMENTS |
| 13/30286132 DC : 0 | BS EN 13616-2 - OVERFILL PREVENTION DEVICES FOR STATIC TANKS FOR LIQUID FUELS - REQUIREMENTS AND TEST/ASSESSMENT METHODS - PART 2: OVERFILL PREVENTION DEVICES WITHOUT CLOSURE DEVICE |
| 12/30270980 DC : 0 | BS EN 1127-2 - EXPLOSIVE ATMOSPHERES - EXPLOSION PREVENTION AND PROTECTION - PART 2: BASIC CONCEPTS AND METHODOLOGY FOR MINING |
| PREN 14986 : DRAFT 2014 | DESIGN OF FANS WORKING IN POTENTIALLY EXPLOSIVE ATMOSPHERES |
| BS EN 12405-1 : 2005 | GAS METERS - CONVERSION DEVICES - PART 1: VOLUME CONVERSION |
| UNE-EN 60079-29-1:2017 | Explosive atmospheres - Part 29-1: Gas detectors - Performance requirements of detectors for flammable gases |
| I.S. EN 13616-1:2016 | OVERFILL PREVENTION DEVICES FOR STATIC TANKS FOR LIQUID FUELS -PART 1: OVERFILL PREVENTION DEVICES WITH CLOSURE DEVICE |
| DIN EN 1010-1:2011-06 | Safety of machinery - Safety requirements for the design and construction of printing and paper converting machines - Part 1: Common requirements (includes Amendment A1:2010) |
| DIN EN 12621:2011-07 | Machinery for the supply and circulation of coating materials under pressure - Safety requirements (includes Amendment A1:2010) |
| DIN EN 12581:2011-02 | Coating plants - Machinery for dip coating and electrodeposition of organic liquid coating material - Safety requirements (includes Amendment A1:2010) |
| DIN EN 13617-1:2012-08 | Petrol filling stations - Part 1: Safety requirements for construction and performance of metering pumps, dispensers and remote pumping units |
| BS EN 1473:2016 | Installation and equipment for liquefied natural gas. Design of onshore installations |
| I.S. EN 14678-1:2013 | LPG EQUIPMENT AND ACCESSORIES - CONSTRUCTION AND PERFORMANCE OF LPG EQUIPMENT FOR AUTOMOTIVE FILLING STATIONS - PART 1: DISPENSERS |
| DIN EN 1473:1997-11 | INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN OF ONSHORE INSTALLATIONS |
| DIN EN 1127-1:2011-10 | EXPLOSIVE ATMOSPHERES - EXPLOSION PREVENTION AND PROTECTION - PART 1: BASIC CONCEPTS AND METHODOLOGY |
| I.S. EN 1127-2:2014 | EXPLOSIVE ATMOSPHERES - EXPLOSION PREVENTION AND PROTECTION - PART 2: BASIC CONCEPTS AND METHODOLOGY FOR MINING |
| I.S. EN 13852-1:2013 | CRANES - OFFSHORE CRANES - PART 1: GENERAL - PURPOSE OFFSHORE CRANES |
| I.S. EN 12621:2006 | MACHINERY FOR THE SUPPLY AND CIRCULATION OF COATING MATERIALS UNDER PRESSURE - SAFETY REQUIREMENTS |
| I.S. EN 12312-5:2005 | AIRCRAFT GROUND SUPPORT EQUIPMENT - SPECIFIC REQUIREMENTS - PART 5: AIRCRAFT FUELLING EQUIPMENT |
| EN 12312-5:2005+A1:2009 | Aircraft ground support equipment - Specific requirements - Part 5: Aircraft fuelling equipment |
| I.S. EN 1473:2016 | INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN OF ONSHORE INSTALLATIONS |
| I.S. EN 13617-1:2012 | PETROL FILLING STATIONS - PART 1: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF METERING PUMPS, DISPENSERS AND REMOTE PUMPING UNITS |
| EN 60079-14:2014/AC:2016 | EXPLOSIVE ATMOSPHERES - PART 14: ELECTRICAL INSTALLATIONS DESIGN, SELECTION AND ERECTION (IEC 60079-14:2013/COR1:2016) |
| I.S. EN 1010-1:2005 | SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PRINTING AND PAPER CONVERTING MACHINES - PART 1: COMMON REQUIREMENTS |
| I.S. EN 14986:2017 | DESIGN OF FANS WORKING IN POTENTIALLY EXPLOSIVE ATMOSPHERES |
| I.S. EN 12581:2006 | COATING PLANTS - MACHINERY FOR DIP COATING AND ELECTRODEPOSITION OF ORGANIC LIQUID COATING MATERIAL - SAFETY REQUIREMENTS |
| VDI/VDE 3518 Blatt 1:2011-05 | Multigas sensors - Terms, configuration, function and classification |
| UNE-EN 13616-1:2016 | Overfill prevention devices for static tanks for liquid fuels - Part 1: Overfill prevention devices with closure device |
| DIN EN 1474-1:2009-03 | INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN AND TESTING OF MARINE TRANSFER SYSTEMS - PART 1: DESIGN AND TESTING OF TRANSFER ARMS |
| PREN 1473 : DRAFT 2018 | INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN OF ONSHORE INSTALLATIONS |
| PREN 13617-1 : DRAFT 2010 | PETROL FILLING STATIONS - PART 1: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF METERING PUMPS, DISPENSERS AND REMOTE PUMPING UNITS |
| PREN 14492-1 : DRAFT 2015 | CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 1: POWER DRIVEN WINCHES |
| 10/30219405 DC : 0 | BS EN 13617-1 - PETROL FILLING STATIONS - PART 1: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF METERING PUMPS, DISPENSERS AND REMOTE PUMPING UNITS |
| 10/30212177 DC : 0 | BS EN 12405-1:2005/A2 - GAS METERS - CONVERSION DEVICES - PART 1: VOLUME CONVERSION |
| EN 1473:2016 | Installation and equipment for liquefied natural gas - Design of onshore installations |
| 09/30209043 DC : 0 | BS EN 13922 - TANKS FOR TRANSPORT OF DANGEROUS GOODS - SERVICE EQUIPMENT FOR TANKS - OVERFILL PREVENTION SYSTEMS FOR LIQUID FUELS |
| 08/30174143 DC : DRAFT SEP 2008 | BS EN 12312-5 AMD1 - AIRCRAFT GROUND SUPPORT EQUIPMENT - SPECIFIC REQUIREMENTS - PART 5: AIRCRAFT FUELLING EQUIPMENT |
| PD CEN/TR 16787:2014 | Industrial Gas Installation. Guideline |
| I.S. EN 60079-14:2014 | EXPLOSIVE ATMOSPHERES - PART 14: ELECTRICAL INSTALLATIONS DESIGN, SELECTION AND ERECTION |
| 14/30294092 DC : 0 | BS EN 14986 - DESIGN OF FANS WORKING IN POTENTIALLY EXPLOSIVE ATMOSPHERES |
| UNI EN 1127-1 : 2011 | EXPLOSIVE ATMOSPHERES - EXPLOSION PREVENTION AND PROTECTION - PART 1: BASIC CONCEPTS AND METHODOLOGY |
| I.S. EN 1474-1:2008 | INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN AND TESTING OF MARINE TRANSFER SYSTEMS - PART 1: DESIGN AND TESTING OF TRANSFER ARMS |
| BS EN 60079-29-1:2007 | Explosive atmospheres Gas detectors. Performance requirements of detectors for flammable gases |
| I.S. EN 12405-1:2005 | GAS METERS - CONVERSION DEVICES - PART 1: VOLUME CONVERSION |
| BS EN 1127-1:2019 | Explosive atmospheres. Explosion prevention and protection Basic concepts and methodology |
| DIN EN 1127-2:2014-09 | EXPLOSIVE ATMOSPHERES - EXPLOSION PREVENTION AND PROTECTION - PART 2: BASIC CONCEPTS AND METHODOLOGY FOR MINING |
| UNE-EN 60079-14:2016 | Explosive atmospheres - Part 14: Electrical installations design, selection and erection |
| BS EN 1010-1 : 2004 | SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PRINTING AND PAPER CONVERTING MACHINES - PART 1: COMMON REQUIREMENTS |
| BS EN 12312-5 : 2005 | AIRCRAFT GROUND SUPPORT EQUIPMENT - SPECIFIC REQUIREMENTS - PART 5: AIRCRAFT FUELLING EQUIPMENT |
| UNE-EN 14678-1:2013 | LPG equipment and accessories - Construction and performance of LPG equipment for automotive filling stations - Part 1: Dispensers |
| I.S. EN 13922:2011 | TANKS FOR TRANSPORT OF DANGEROUS GOODS - SERVICE EQUIPMENT FOR TANKS - OVERFILL PREVENTION SYSTEMS FOR LIQUID FUELS |
| BS EN 60079-14:2014 | Explosive atmospheres Electrical installations design, selection and erection |
| EN 1474-1:2008 | Installation and equipment for liquefied natural gas - Design and testing of marine transfer systems - Part 1: Design and testing of transfer arms |
| EN 14678-1:2013 | LPG equipment and accessories - Construction and performance of LPG equipment for automotive filling stations - Part 1: Dispensers |
| UNI EN 13617-1 : 2012 | PETROL FILLING STATIONS - PART 1: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF METERING PUMPS, DISPENSERS AND REMOTE PUMPING UNITS |
| UNI EN 12581 : 2010 | COATING PLANTS - MACHINERY FOR DIP COATING AND ELECTRODEPOSITION OF ORGANIC LIQUID COATING MATERIAL - SAFETY REQUIREMENTS |
| UNI EN 1010-1 : 2011 | SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PRINTING AND PAPER CONVERTING MACHINES - PART 1: COMMON REQUIREMENTS |
| UNI EN 13852-1 : 2013 | CRANES - OFFSHORE CRANES - PART 1: GENERAL-PURPOSE OFFSHORE CRANES |
| UNI EN 1127-2 : 2014 | EXPLOSIVE ATMOSPHERES - EXPLOSION PREVENTION AND PROTECTION - PART 2: BASIC CONCEPTS AND METHODOLOGY FOR MINING |
| UNI EN 14678-1 : 2013 | LPG EQUIPMENT AND ACCESSORIES - CONSTRUCTION AND PERFORMANCE OF LPG EQUIPMENT FOR AUTOMOTIVE FILLING STATIONS - PART 1: DISPENSERS |
| UNI EN 12621 : 2010 | MACHINERY FOR THE SUPPLY AND CIRCULATION OF COATING MATERIALS UNDER PRESSURE - SAFETY REQUIREMENTS |
| I.S. EN 60079-0:2012 | EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS (IEC 60079-0:2011 (MOD)) |
| 10/30214970 DC : 0 | BS EN 13616 - OVERFILL PREVENTION DEVICES FOR STATIC TANKS FOR LIQUID PETROLEUM FUELS |
| 13/30286135 DC : 0 | BS EN 13616-1 - OVERFILL PREVENTION DEVICES FOR STATIC TANKS FOR LIQUID FUELS - REQUIREMENTS AND TEST/ASSESSMENT METHODS - PART 1: OVERFILL PREVENTION DEVICES WITH CLOSURE DEVICE |
| BS EN 1474-1:2008 | Installation and equipment for liquefied natural gas. Design and testing of marine transfer systems Design and testing of transfer arms |
| BS EN 13616-1:2016 | Overfill prevention devices for static tanks for liquid fuels Overfill prevention devices with closure device |
| 09/30182347 DC : 0 | BS EN 12621:2006/A1 - MACHINERY FOR THE SUPPLY AND CIRCULATION OF COATING MATERIALS UNDER PRESSURE - SAFETY REQUIREMENTS |
| BS EN 60079-2:2014 | Explosive atmospheres Equipment protection by pressurized enclosure \'p\' |
| UNI EN 12405-1 : 2010 | GAS METERS - CONVERSION DEVICES - PART 1: VOLUME CONVERSION |
| I.S. EN 60601-1:2006&A1:2013&AC:2014&A12:2014 | MEDICAL ELECTRICAL EQUIPMENT - PART 1: GENERAL REQUIREMENTS FOR BASIC SAFETY AND ESSENTIAL PERFORMANCE |
| EN 12405-1:2005+A2:2010 | Gas meters - Conversion devices - Part 1: Volume conversion |
| EN 13922:2011 | Tanks for transport of dangerous goods - Service equipment for tanks - Overfill prevention systems for liquid fuels |
| DIN EN 13852-1:2014-01 | Cranes - Offshore cranes - Part 1: General-purpose offshore cranes |
| BS EN 60601-1 : 2006 | MEDICAL ELECTRICAL EQUIPMENT PART 1: GENERAL REQUIREMENTS FOR BASIC SAFETY AND ESSENTIAL PERFORMANCE |
| UNE-EN 12621:2006 | Machinery for the supply and circulation of coating materials under pressure - Safety requirements |
| BS EN 14986:2007 | Design of fans working in potentially explosive atmospheres |
| BS EN 13617-1:2012 | Petrol filling stations Safety requirements for construction and performance of metering pumps, dispensers and remote pumping units |
| BS EN 12621 : 2006 | MACHINERY FOR THE SUPPLY AND CIRCULATION OF COATING MATERIALS UNDER PRESSURE - SAFETY REQUIREMENTS |
| UNE-EN 60079-0:2013 | Explosive atmospheres - Part 0: Equipment - General requirements |
| UNE-EN 14986:2017 | Design of fans working in potentially explosive atmospheres |
| BS EN 1127-2:2014 | Explosive atmospheres. Explosion prevention and protection Basic concepts and methodology for mining |
| UNE-EN 13617-1:2012 | Petrol filling stations - Part 1: Safety requirements for construction and performance of metering pumps, dispensers and remote pumping units |
| BS EN 13922:2011 | Tanks for transport of dangerous goods. Service equipment for tanks. Overfill prevention systems for liquid fuels |
| UNE-EN 60079-2:2015 | Explosive atmospheres - Part 2: Equipment protection by pressurized enclosure "p" |
| UNE-EN 13922:2012 | Tanks for transport of dangerous goods - Service equipment for tanks - Overfill prevention systems for liquid fuels |
| UNE-EN 13852-1:2014 | Cranes - Offshore cranes - Part 1: General-purpose offshore cranes |
| EN 14986:2017 | Design of fans working in potentially explosive atmospheres |
| EI MODEL CODE SAFE PRACTICE PT1 : 2010 | THE SELECTION, INSTALLATION, INSPECTION, AND MAINTENANCE OF ELECTRICAL AND NON ELECTRICAL APPARATUS IN HAZARDOUS AREAS |
| EN 12581:2005+A1:2010 | Coating plants - Machinery for dip coating and electrodeposition of organic liquid coating material - Safety requirements |
| EN 13616-1:2016 | Overfill prevention devices for static tanks for liquid fuels - Part 1: Overfill prevention devices with closure device |
| EN 13852-1:2013 | Cranes - Offshore cranes - Part 1: General-purpose offshore cranes |
| 08/30186475 DC : 0 | BS EN 13617-1 AMD1 - PETROL FILLING STATIONS - PART 1: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF METERING PUMPS, DISPENSERS AND REMOTE PUMPING UNITS |
| BS EN 60079-0 : 2012 | EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS |
| PREN 1127-2 : DRAFT 2012 | EXPLOSIVE ATMOSPHERES - EXPLOSION PREVENTION AND PROTECTION - PART 2: BASIC CONCEPTS AND METHODOLOGY FOR MINING |
| I.S. EN 1127-1:2011 | EXPLOSIVE ATMOSPHERES - EXPLOSION PREVENTION AND PROTECTION - PART 1: BASIC CONCEPTS AND METHODOLOGY |
| EN 60079-18:2015/A1:2017 | EXPLOSIVE ATMOSPHERES - PART 18: EQUIPMENT PROTECTION BY ENCAPSULATION 'M' (IEC 60079-18:2014/A1:2017) |
| 17/30356731 DC : 0 | BS EN 12405-1 - GAS METERS - CONVERSION DEVICES - PART 1: VOLUME CONVERSION |
| BS EN 1127-1:2011 | Explosive atmospheres. Explosion prevention and protection Basic concepts and methodology |
| EN 13617-1:2012 | Petrol filling stations - Part 1: Safety requirements for construction and performance of metering pumps, dispensers and remote pumping units |
| NF EN 12312-5 : 2005 + A1 2010 | AIRCRAFT GROUND SUPPORT EQUIPMENT - SPECIFIC REQUIREMENTS - PART 5: AIRCRAFT FUELLING EQUIPMENT |
| DIN EN 14678-1:2013-06 | LPG equipment and accessories - Construction and performance of LPG equipment for automotive filling stations - Part 1: Dispensers |
| DIN EN 12405-1:2011-04 | GAS METERS - CONVERSION DEVICES - PART 1: VOLUME CONVERSION |
| BS EN 12581 : 2005 | COATING PLANTS - MACHINERY FOR DIP COATING AND ELECTRODEPOSITION OF ORGANIC LIQUID COATING MATERIAL - SAFETY REQUIREMENTS |
| BS EN 14678-1:2013 | LPG equipment and accessories. Construction and performance of LPG equipment for automotive filling stations Dispensers |
| BS EN 13852-1:2013 | Cranes. Offshore cranes General-purpose offshore cranes |
| EN 60079-2:2014/AC:2015 | EXPLOSIVE ATMOSPHERES - PART 2: EQUIPMENT PROTECTION BY PRESSURIZED ENCLOSURE 'P' (IEC 60079-2:2014) |
| EN 60079-0:2012/A11:2013 | EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS (IEC 60079-0:2011, MODIFIED) |
| EN 1127-2:2014 | Explosive atmospheres - Explosion prevention and protection - Part 2: Basic concepts and methodology for mining |
| EN 1127-1:2011 | Explosive atmospheres - Explosion prevention and protection - Part 1: Basic concepts and methodology |
| ISO 3016:1994 | Petroleum products Determination of pour point |
| ISO 2719:2016 | Determination of flash point — Pensky-Martens closed cup method |
| EN 60156:1995 | Insulating liquids - Determination of the breakdown voltage at power frequency - Test method |
| IEC 62021-1:2003 | Insulating liquids - Determination of acidity - Part 1: Automatic potentiometric titration |
| IEC 61125:1992 | Unused hydrocarbon based insulating liquids - Test methods for evaluating the oxidation stability |
| EN ISO 3104:1996 | Petroleum products - Transparent and opaque liquids - Determination of kinematic viscosity and calculation of dynamic viscosity (ISO 3104:1994) |
| EN 60079-0:2012/A11:2013 | EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS (IEC 60079-0:2011, MODIFIED) |
| IEC 60050-441:1984 | International Electrotechnical Vocabulary (IEV) - Part 441: Switchgear, controlgear and fuses |
| IEC 60156:1995 | Insulating liquids - Determination of the breakdown voltage at power frequency - Test method |
| EN 61125:1993/A1:2004 | UNUSED HYDROCARBON-BASED INSULATING LIQUIDS - TEST METHODS FOR EVALUATING THE OXIDATION STABILITY |
| EN 61099:2010 | Insulating liquids - Specifications for unused synthetic organic esters for electrical purposes |
| IEC 62535:2008 | Insulating liquids - Test method for detection of potentially corrosive sulphur in used and unused insulating oil |
| IEC 62770:2013 | Fluids for electrotechnical applications - Unused natural esters for transformers and similar electrical equipment |
| IEC 61099:2010 | Insulating liquids - Specifications for unused synthetic organic esters for electrical purposes |
| EN 60814:1997 | Insulating liquids - Oil-impregnated paper and pressboard - Determination of water by automatic coulometric Karl Fischer titration |
| EN 62770:2014 | Fluids for electrotechnical applications - Unused natural esters for transformers and similar electrical equipment |
| EN 62535:2009 | Insulating liquids - Test method for detection of potentially corrosive sulphur in used and unused insulating oil |
| IEC 60836:2015 | Specifications for unused silicone insulating liquids for electrotechnical purposes |
| IEC 60296:2012 RLV | Fluids for electrotechnical applications - Unused mineral insulating oils for transformers and switchgear |
| IEC 60050-421:1990 | International Electrotechnical Vocabulary (IEV) - Part 421: Power transformers and reactors |
| EN 60296:2012 | Fluids for electrotechnical applications - Unused mineral insulating oils for transformers and switchgear |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| EN 60836:2015 | Specifications for unused silicone insulating liquids for electrotechnical purposes |
| EN 60247:2004 | Insulating liquids - Measurement of relative permittivity, dielectric dissipation factor (tan d) and d.c. resistivity |
| IEC 60079-0:2011 | Explosive atmospheres - Part 0: Equipment - General requirements |
| IEC 60814:1997 | Insulating liquids - Oil-impregnated paper and pressboard - Determination of water by automatic coulometric Karl Fischer titration |
| EN ISO 2719:2016 | Determination of flash point - Pensky-Martens closed cup method (ISO 2719:2016) |
| IEC 60247:2004 | Insulating liquids - Measurement of relative permittivity, dielectric dissipation factor (tan d) and d.c. resistivity |
| EN ISO 2592:2017 | Petroleum and related products - Determination of flash and fire points - Cleveland open cup method (ISO 2592:2017) |
| EN 50495:2010 | Safety devices required for the safe functioning of equipment with respect to explosion risks |
| EN 62021-1:2003 | Insulating liquids - Determination of acidity - Part 1: Automatic potentiometric titration |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.