EN 45012 : 1998
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
GENERAL REQUIREMENTS FOR BODIES OPERATING ASSESSMENT AND CERTIFICATION/REGISTRATION OF QUALITY SYSTEMS
09-01-2006
01-12-2013
Section 1: General
1.1 Scope
1.1 References
1.3 Definitions
Section 2: Requirements for certification/registration
bodies
2.1 Certification/registration body
2.1.1 General provisions
2.1.2 Organization
2.1.3 Subcontracting
2.1.4 Quality system
2.1.5 Conditions for granting, maintaining, extending
reducing, suspending and withdrawing certificate/
registration
2.1.6 Internal audits and management reviews
2.1.7 Documentation
2.1.8 Records
2.1.9 Confidentiality
2.2 Certification/registration body personnel
2.2.1 General
2.2.2 Qualification criteria for auditors and
technical experts
2.2.3 Selection procedure
2.2.4 Contracting of assessment personnel
2.2.5 Assessment personnel records
2.2.6 Procedures for audit teams
2.3 Changes in the certification/registration requirements
2.4 Appeals, complaints and disputes
Section 3: Requirements for certification/registration
3.1 Application for certification/registration
3.1.1 Information on the procedure
3.1.2 The application
3.2 Preparation for assessment
3.3 Assessment
3.4 Assessment report
3.5 Decision on certification/registration
3.6 Surveillance and reassessment procedures
3.7 Use of certificates and logos
3.8 Access to records of complaints to suppliers
Annex ZA (normative) Normative references to international
publications with their relevant
European publications
Defines general requirements for a third-party body operating quality system certification/registration to meet for recognition as competent and reliable in the operating of quality system certification/registration.
Committee |
TC 1
|
DocumentType |
Standard
|
PublisherName |
European Committee for Standards - Electrical
|
Status |
Superseded
|
SupersededBy |
Standards | Relationship |
ISO/IEC Guide 62:1996 | Identical |
UNE-EN 45012:1998 | Identical |
DIN EN 45012:1990-05 | Identical |
UNI CEI EN 45012 : 1998 | Corresponds |
BS 7512:1989 | Corresponds |
I.S. EN 45012:1998 | Identical |
UNE 66512:1991 | Identical |
BS EN 45012:1998 | Identical |
S.R. CEN/TS 12666-2:2012 | PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - POLYETHYLENE (PE) - PART 2: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY |
PD CEN/TS 13476-4:2013 | Plastics piping systems for non-pressure underground drainage and sewerage. Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) Guidance for the assessment of conformity |
UNI CEN/TS 13476-4 : 2013 | PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYLS CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 4: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY |
DD ENV 1852-2:2001 | Plastics piping systems for non-pressure underground drainage and sewerage. Polypropylene (PP) Guidance for the assessment of conformity |
I.S. EN 13566-1:2003 | PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NON-PRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 1: GENERAL |
11/30231856 DC : 0 | BS EN 14125 - THERMOPLASTIC AND FLEXIBLE METAL PIPEWORK FOR UNDERGROUND INSTALLATION AT PETROL FILLING STATIONS |
14/30272915 DC : 0 | BS ISO 18400-106 - SOIL QUALITY - SAMPLING - PART 106: QUALITY CONTROL AND QUALITY ASSURANCE |
I.S. EN 1457:1999 | CHIMNEYS - CLAY/CERAMIC FLUE LINERS - REQUIREMENTS AND TEST METHODS |
02/711556 DC : 0 | LINKS FOR USE WITH STEEL CHAINS OF GRADE 8 |
DD ENV 1329-2:2001 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Unplasticized poly(vinyl chloride) (PVC-U) Guidance for the assessment of conformity |
PD CEN/TS 1455-2:2012 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Acrylonitrile-butadiene-styrene (ABS) Guidance for the assessment of conformity |
DD ENV 1453-2:2001 | Plastics piping systems with structured wall pipes for soil and waste discharge (low and high temperature) inside buildings. Unplasticized poly(vinyl chloride) (PVC-U) Guidance for the assessment of conformity |
97/109273 DC : DRAFT DEC 1997 | PREN 13069 - CHIMNEYS - CLAY/CERAMIC OUTER WALLS FOR SYSTEM CHIMNEYS - REQUIREMENTS AND TEST METHODS |
02/103630 DC : DRAFT MAY 2002 | PREN 12446 - CHIMNEYS - COMPONENTS - CONCRETE OUTER WALL ELEMENTS |
UNI CEN/TS 1455-2 : 2012 | PLASTICS PIPING SYSTEMS FOR SOIL AND WASTE DISCHARGE (LOW AND HIGH TEMPERATURE) WITHIN THE BUILDING STRUCTURE - ACRYLONITRILE-BUTADIENE-STYRENE (ABS) - PART 2: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY |
PD CEN/TS 12666-2:2012 | Plastics piping systems for non-pressure underground drainage and sewerage. Polyethylene (PE) Guidance for the assessment of conformity |
98/105109 DC : DRAFT JUNE 1998 | PREN 1317-5 - ROAD RESTRAINT SYSTEMS - PART 5: DURABILITY AND EVALUATION OF CONFORMITY |
UNE-CEN/TS 1555-7:2015 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 7: Guidance for the assessment of conformity |
EN 1279-6:2002 | Glass in building - Insulating glass units - Part 6: Factory production control and periodic tests |
DIN EN 15655:2016-07 (Draft) | DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - INTERNAL POLYURETHANE LINING FOR PIPES AND FITTINGS - REQUIREMENTS AND TEST METHODS |
EN 13411-7:2006+A1:2008 | Terminations for steel wire ropes - Safety - Part 7: Symmetric wedge socket |
S.R. CEN/TS 1566-2:2012 | PLASTICS PIPING SYSTEMS FOR SOIL AND WASTE DISCHARGE (LOW AND HIGH TEMPERATURE) WITHIN THE BUILDING STRUCTURE - CHLORINATED POLY(VINYL CHLORIDE) (PVC-C) - PART 2: GUIDANCE FOR ASSESSMENT OF CONFORMITY |
PREN 1825-1 : DRAFT 1995 | INSTALLATIONS FOR SEPARATION OF GREASE - PRINCIPLES OF DESIGN, PERFORMANCE AND TESTING, MARKING AND QUALITY CONTROL |
I.S. CWA 14172-2:2004 | EESSI CONFORMITY ASSESSMENT GUIDANCE - PART 2: CERTIFICATION AUTHORITY SERVICES AND PROCESSES |
S.R. CEN/TS 1329-2:2012 | PLASTICS PIPING SYSTEMS FOR SOIL AND WASTE DISCHARGE (LOW AND HIGH TEMPERATURE) WITHIN THE BUILDING STRUCTURE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) - PART 2: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY |
DD CEN/TS 14632:2006 | Plastics piping systems for drainage, sewerage and water supply, pressure and non-pressure. Glass-reinforced thermosetting plastics (GRP) based on polyester resin (UP). Guidance for the assessment of conformity |
UNI EN 1457-1 : 2012 | CHIMNEYS - CLAY/CERAMIC FLUE LINERS - PART 1: FLUE LINERS OPERATING UNDER DRY CONDITIONS - REQUIREMENTS AND TEST METHODS |
I.S. CWA 14172-7:2004 | EESSI CONFORMITY ASSESSMENT GUIDANCE - PART 7: CRYPTOGRAPHIC MODULES USED BY CERTIFICATION SERVICE PROVIDERS FOR SIGNING OPERATIONS AND KEY GENERATION SERVICES |
EN ISO/TS 15874-7 : 2003 | PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - POLYPROPYLENE (PP) - PART 7: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY |
EN 545:2010 | Ductile iron pipes, fittings, accessories and their joints for water pipelines - Requirements and test methods |
BS EN 14525:2004 | Ductile iron wide tolerance couplings and flange adaptors for use with pipes of different materials: ductile iron, grey iron, steel, PVC-U, PE, fibre-cement |
BS EN 13980:2002 | Potentially explosive atmospheres. Application of quality systems |
BS EN 14408-1:2004 | Plastics piping systems for renovation of underground gas supply networks General |
BS EN 14628:2005 | Ductile iron pipes, fittings and accessories. External polythene coating for pipes. Requirements and test methods |
BS EN 681-1:1996 | Elastomeric seals. Material requirements for pipe joint seals used in water and drainage applications Vulcanized rubber |
I.S. EN 10242:1995 | THREADED PIPE FITTING IN MALLEABLE CAST IRON |
EN 13069:2005 | Chimneys - Clay/ceramic outer walls for system chimneys - Requirements and test methods |
CEN/TS 13598-3:2012 | Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride)(PVC-U), polypropylene (PP) and polyethylene (PE) - Part 3: Guidance for assessment of conformity |
CEN/TS 12666-2:2012 | Plastics piping systems for non-pressure underground drainage and sewerage - Polyethylene (PE) - Part 2: Guidance for the assessment of conformity |
CEN/TS 13476-4:2013 | Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 4: Guidance for the assessment of conformity |
DIN EN 12094-9:2003-07 | FIXED FIREFIGHTING SYSTEMS - COMPONENTS FOR GAS EXTINGUISHING SYSTEMS - PART 9: REQUIREMENTS AND TEST METHODS FOR SPECIAL FIRE DETECTORS |
EN 12408:2004 | Safety requirements for cableway installations designed to carry persons - Quality assurance |
EN 1293:1999 | General requirements for components used in pneumatically pressurized discharge pipes, drains and sewers |
CEN/TS 1566-2:2012 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Chlorinated poly(vinyl chloride) (PVC-C) - Part 2: Guidance for assessment of conformity |
UNI EN 13411-7 : 2009 | TERMINATIONS FOR STEEL WIRE ROPES - SAFETY - PART 7: SYMMETRIC WEDGE SOCKET |
EN 13411-6:2004+A1:2008 | Terminations for steel wire ropes - Safety - Part 6: Asymmetric wedge socket |
CEN/TS 1455-2:2012 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Acrylonitrile-butadiene-styrene (ABS) - Part 2: Guidance for the assessment of conformity |
DIN EN 15189:2007-02 | Ductile iron pipes, fittings and accessories - External polyurethane coating for pipes - Requirements and test methods |
DIN EN 13889:2009-02 | FORGED STEEL SHACKLES FOR GENERAL LIFTING PURPOSES - DEE SHACKLES AND BOW SHACKLES, GRADE 6 - SAFETY |
BS EN 1457:1999 | Chimneys. Clay/ceramic flue liners. Requirements and test methods |
SBAC TS 157 : 6 | AEROSPACE SECTOR CERTIFICATION SCHEME (ASCS) - REQUIREMENTS AND PROCEDURES |
ENV 1452-7:2000 | Plastics piping systems for water supply - Unplasticized poly(vinyl chloride) (PVC-U) - Part 7: Guidance for the assessment of conformity |
I.S. EN 1492-1:2000 | TEXTILE SLINGS - SAFETY - PART 1: FLAT WOVEN WEBBING SLINGS MADE OF MAN-MADE FIBRES FOR GENERAL PURPOSE USE |
97/102971 DC : DRAFT APR 1997 | PREN 12843 - PRECAST CONCRETE MASTS AND POSTS |
UNE-EN 1457-2:2013 | Chimneys - Clay/ceramic flue liners - Part 2: Flue liners operating under wet conditions - Requirements and test methods |
PD CEN/TS 1401-2:2012 | Plastics piping systems for non-pressure underground drainage and sewerage. Unplasticized poly(vinyl chloride) (PVC-U) Guidance for assessment of conformity |
97/101296 DC : DRAFT FEB 1997 | PREN 12737 - PRECAST CONCRETE FLOOR SLATS FOR LIVESTOCK |
PD CEN/TS 13598-3:2012 | Plastics piping systems for non-pressure underground drainage and sewerage. Unplasticized poly(vinyl chloride)(PVC-U), polypropylene (PP) and polyethylene (PE) Guidance for assessment of conformity |
03/102154 DC : DRAFT MAY 2003 | CEN TS 14632 - PLASTICS PIPING SYSTEMS FOR DRAINAGE, SEWERAGE AND WATER SUPPLY, PRESSURE AND NON-PRESSURE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON UNSATURATED POLYESTER RESIN (UP) - GUIDANCE FOR THE ASSESSMENT OF CONFORMITY |
10/30216654 DC : 0 | BS EN 12842 - DUCTILE IRON FITTINGS FOR PVC-U OR PE PIPING SYSTEMS - REQUIREMENTS AND TEST METHODS |
UNI EN 15655 : 2009 | DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - INTERNAL POLYURETHANE LINING FOR PIPES AND FITTINGS - REQUIREMENTS AND TEST METHODS |
PD CEN/TS 1451-2:2012 | Plastic piping systems for soil and waste discharge (low and high temperature) within the building structure. Polypropylene (PP) Guidance for the assessment of conformity |
UNI CEN/TS 1519-2 : 2012 | PLASTIC PIPING SYSTEMS FOR SOIL AND WASTE DISCHARGE (LOW AND HIGH TEMPERATURE) WITHIN THE BUILDING STRUCTURE - POLYETHYLEN (PE) - PART 2: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY |
00/541127 DC : DRAFT AUG 2000 | BS EN 13980 - POTENTIALLY EXPLOSIVE ATMOSPHERES - APPLICATION OF QUALITY SYSTEMS |
BS ISO 18400-106:2017 | Soil quality. Sampling Quality control and quality assurance |
DD ENV 1451-2:2001 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Polypropylene (PP) Guidance for the assessment of conformity |
05/30131064 DC : DRAFT MAR 2005 | EN 15189:2005 - DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - EXTERNAL POLYURETHANE COATING FOR PIPES - REQUIREMENTS AND TEST METHODS |
16/30340626 DC : 0 | BS EN 15655 - DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - INTERNAL POLYURETHANE LINING FOR PIPES AND FITTINGS - REQUIREMENTS AND TEST METHODS |
DD CEN/TS 12201-7:2003 | Plastics piping systems for water supply. Polyethylene (PE) Guidance for the assessment of conformity |
UNI CEN/TS 12666-2 : 2012 | PLASTICS PIPING SYSTEMS FOR NON- PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - POLYETHYLENE (PE) - PART 2: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY |
S.R. CEN/TS 14632:2012 | PLASTICS PIPING SYSTEMS FOR DRAINAGE, SEWERAGE AND WATER SUPPLY, PRESSURE AND NON-PRESSURE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON UNSATURATED POLYESTER RESIN (UP) - GUIDANCE FOR THE ASSESSMENT OF CONFORMITY |
CEN/TS 1456-2:2003 | Plastics piping systems for buried and above-ground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 2: Guidance for the assessment of conformity |
I.S. EN 1457-2:2012 | CHIMNEYS - CLAY/CERAMIC FLUE LINERS - PART 2: FLUE LINERS OPERATING UNDER WET CONDITIONS - REQUIREMENTS AND TEST METHODS |
S.R. CEN/TS 1401-2:2012 | PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) - PART 2: GUIDANCE FOR ASSESSMENT OF CONFORMITY |
UNI CEN/TS 1329-2 : 2012 | PLASTICS PIPING SYSTEMS FOR SOIL AND WASTE DISCHARGE (LOW AND HIGH TEMPERATURE) WITHIN THE BUILDING STRUCTURE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) - PART 2: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY |
DD CEN/TS 1456-2:2003 | Plastic piping systems for buried and above-ground drainage and sewerage under pressure. Unplasticized poly(vinyl chloride) (PVC-U) Guidance for the assessment of conformity |
ISO/TS 15875-7:2003 | Plastics piping systems for hot and cold water installations Crosslinked polyethylene (PE-X) Part 7: Guidance for the assessment of conformity |
I.S. CEN TS 1555-7:2003 | PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 7: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY |
DIN EN 1677-4:2009-03 | COMPONENTS FOR SLINGS - SAFETY - PART 4: LINKS, GRADE 8 |
DIN EN 1677-1:2009-03 | COMPONENTS FOR SLINGS - SAFETY - PART 1: FORGED STEEL COMPONENTS, GRADE 8 |
DIN EN 1916:2003-04 | CONCRETE PIPES AND FITTINGS, UNREINFORCED, STEEL FIBRE AND REINFORCED |
DIN EN 12842:2012-11 | Ductile iron fittings for PVC-U or PE piping systems - Requirements and test methods |
DIN EN 1677-5:2009-03 | COMPONENTS FOR SLINGS - SAFETY - PART 5: FORGED STEEL LIFTING HOOKS WITH LATCH - GRADE 4 |
DIN EN 1492-2:2009-05 | TEXTILE SLINGS - SAFETY - PART 2: ROUNDSLINGS MADE OF MAN-MADE FIBRES FOR GENERAL PURPOSE USE |
DIN EN 12408:2005-06 | Safety requirements for cableway installations designed to carry persons - Quality control |
DIN EN 14408-1:2004-12 | PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND GAS SUPPLY NETWORKS - PART 1: GENERAL |
DIN EN 1917:2003-04 | CONCRETE MANHOLES AND INSPECTION CHAMBERS, UNREINFORCED, STEEL FIBRE AND REINFORCED |
BS EN 10242:1995 | Threaded pipe fittings in malleable cast iron |
UNE-EN 545:2011 | Ductile iron pipes, fittings, accessories and their joints for water pipelines - Requirements and test methods |
BS EN 13380:2001 | General requirements for components used for renovation and repair of drain and sewer systems outside buildings |
BS EN 1492-2 : 2000 | TEXTILE SLINGS - SAFETY - PART 2: ROUNDSLINGS MADE OF MAN-MADE FIBRES, FOR GENERAL PURPOSE USE |
BS EN 45011:1998 | General requirements for bodies operating product certification systems |
CEN/TS 1519-2:2012 | Plastic piping systems for soil and waste discharge (low and high temperature) within the building structure - Polyethylen (PE) - Part 2: Guidance for the assessment of conformity |
DIN EN 681-1:2006-11 | Elastomeric seals - Material requirements for pipe joint seals used in water and drainage applications - Part 1: Vulcanized rubber |
I.S. EN 12842:2012 | DUCTILE IRON FITTINGS FOR PVC-U OR PE PIPING SYSTEMS - REQUIREMENTS AND TEST METHODS |
I.S. EN 969:2009 | DUCTILE IRON PIPES, FITTINGS, ACCESSORIES AND THEIR JOINTS FOR GAS PIPELINES - REQUIREMENTS AND TEST METHODS |
DIN EN 14409-1:2004-12 | PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND WATER SUPPLY NETWORKS - PART 1: GENERAL |
I.S. EN 1806:2006 | CHIMNEYS - CLAY/CERAMIC FLUE BLOCKS FOR SINGLE WALL CHIMNEYS - REQUIREMENTS AND TEST METHODS |
I.S. EN 13889:2003 | FORGED STEEL SHACKLES FOR GENERAL LIFTING PURPOSES - DEE SHACKLES AND BOW SHACKLES - GRADE 6 - SAFETY |
I.S. EN 14628:2005 | DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - EXTERNAL POLYETHYLENE COATING FOR PIPES - REQUIREMENTS AND TEST METHODS |
I.S. EN 1677-5:2001 | COMPONENTS FOR SLINGS - SAFETY - PART 5: FORGED STEEL LIFTING HOOKS WITH LATCH - GRADE 4 |
I.S. EN 1492-2:2000 | TEXTILE SLINGS - SAFETY - PART 2: ROUNDSLINGS MADE OF MAN-MADE FIBRES FOR GENERAL PURPOSE USE |
DIN EN 1857:2010-08 | Chimneys - Components - Concrete flue liners |
I.S. EN 1677-6:2001 | COMPONENTS FOR SLINGS - SAFETY - PART 6: LINKS - GRADE 4 |
I.S. EN 1677-4:2001 | COMPONENTS FOR SLINGS - SAFETY - PART 4: LINKS, GRADE 8 |
I.S. EN 13411-6:2004 | TERMINATIONS FOR STEEL WIRE ROPES - SAFETY - PART 6: ASYMMETRIC WEDGE SOCKET |
I.S. EN 545:2010 | DUCTILE IRON PIPES, FITTINGS, ACCESSORIES AND THEIR JOINTS FOR WATER PIPELINES - REQUIREMENTS AND TEST METHODS |
I.S. EN 13411-7:2006 | TERMINATIONS FOR STEEL WIRE ROPES - SAFETY - PART 7: SYMMETRIC WEDGE SOCKET |
I.S. EN 14125:2013 | THERMOPLASTIC AND FLEXIBLE METAL PIPEWORK FOR UNDERGROUND INSTALLATION AT PETROL FILLING STATIONS |
I.S. EN 1677-1:2000 | COMPONENTS FOR SLINGS - SAFETY - PART 1: FORGED STEEL COMPONENTS, GRADE 8 |
DIN EN 13069:2005-12 | Chimneys - Clay/ceramic outer walls for system chimneys - Requirements and test methods |
DIN ISO 10381-1:2003-08 | SOIL QUALITY - SAMPLING - PART 1: GUIDANCE ON THE DESIGN OF SAMPLING PROGRAMMES |
I.S. EN 1857:2010 | CHIMNEYS - COMPONENTS - CONCRETE FLUE LINERS |
UNI EN 1677-6 : 2009 | COMPONENTS FOR SLINGS - SAFETY - PART 6: LINKS - GRADE 4 |
DIN V ENV 1452-7:2001-03 | PLASTICS PIPING SYSTEMS FOR WATER SUPPLY - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) - PART 7: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY |
I.S. EN ISO/TS 15876-7:2004 | PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - POLYBUTYLENE (PB) - PART 7: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY |
UNI CEN/TS 1565-2 : 2012 | PLASTICS PIPING SYSTEMS FOR SOIL AND WASTE DISCHARGE (LOW AND HIGH TEMPERATURE) WITHIN THE BUILDING STRUCTURE - STYRENE-COPOLYMER BLENDS (SAN+PVC) - PART 2: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY |
PREN 12842 : DRAFT 2010 | DUCTILE IRON FITTINGS FOR PVC-U OR PE PIPING SYSTEMS - REQUIREMENTS AND TEST METHODS |
DD ENV 1566-2:2001 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Chlorinated poly(vinyl chloride) (PVC-C) Guidance for the assessment of conformity |
02/121563 DC : DRAFT APR 2002 | BS EN 14409-1 - PLASTICS PIPING SYSTEMS FOR THE RENOVATION OF UNDERGROUND WATER SUPPLY NETWORKS - PART 1: GENERAL |
97/109272 DC : DRAFT DEC 1997 | PREN 13063 - CHIMNEYS - SYSTEM CHIMNEYS WITH CLAY/CERAMIC FLUE LINERS OR BLOCKS |
UNE-EN 1457-1:2013 | Chimneys - Clay/ceramic flue liners - Part 1: Flue liners operating under dry conditions - Requirements and test methods |
UNI CEN/TS 14632 : 2012 | PLASTICS PIPING SYSTEMS FOR DRAINAGE, SEWERAGE AND WATER SUPPLY, PRESSURE AND NON-PRESSURE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON UNSATURATED POLYESTER RESIN (UP) - GUIDANCE FOR THE ASSESSMENT OF CONFORMITTY |
I.S. ENV 1452-7:2000 | PLASTICS PIPING SYSTEMS FOR WATER SUPPLY - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) - PART 7: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY |
02/710115 DC : DRAFT AUG 2002 | PREN 14525 - DUCTILE IRON WIDE TOLERANCE COUPLINGS AND FLANGE ADAPTORS FOR USE WITH PIPES OF DIFFERENT MATERIALS: DUCTILE IRON, GREY IRON, STEEL, PVC-U PE, FIBRE-CEMENT |
UNI CEN/TS 1566-2 : 2012 | PLASTICS PIPING SYSTEMS FOR SOIL AND WASTE DISCHARGE (LOW AND HIGH TEMPERATURE) WITHIN THE BUILDING STRUCTURE - CHORINATED POLY(VINYL CHLORIDE) (PVC-C) - PART 2: GUIDANCE FOR ASSESSMENT OF CONFORMITY |
PD CEN/TS 1566-2:2012 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Chlorinated poly(vinyl chloride) (PVC-C) Guidance for assessment of conformity |
I.S. CEN TS 12666-2:2006 | PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - POLYETHYLENE (PE) - PART 2: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY |
DD ENV 1455-2:2001 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Acrylonitrile-butadiene- styrene (ABS) Guidance for the assessment of conformity |
S.R. CEN/TS 1565-2:2012 | PLASTICS PIPING SYSTEMS FOR SOIL AND WASTE DISCHARGE (LOW AND HIGH TEMPERATURE) WITHIN THE BUILDING STRUCTURE - STYRENE-COPOLYMER BLENDS (SAN+PVC) - PART 2: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY |
PD CEN/TS 1555-7:2013 | Plastics piping systems for the supply of gaseous fuels. Polyethylene (PE) Guidance for the assessment of conformity |
DD ENV 1452-7:2001 | Plastics piping systems for water supply. Unplasticized poly(vinyl chloride) (PVC-U) Guidance for the assessment of conformity |
95/101288 DC : DRAFT FEB 1995 | PREN 1825-1 - INSTALLATIONS FOR SEPARATION OF GREASE - PART 1: PRINCIPLES OF DESIGN, PERFORMANCE AND TESTING, MARKING AND QUALITY CONTROL |
DD ENV 1519-2:2001 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Polyethylene (PE) Guidance for the assessment of conformity |
I.S. EN 1457-1:2012 | CHIMNEYS - CLAY/CERAMIC FLUE LINERS - PART 1: FLUE LINERS OPERATING UNDER DRY CONDITIONS - REQUIREMENTS AND TEST METHODS |
S.R. CEN/TS 1455-2:2012 | PLASTICS PIPING SYSTEMS FOR SOIL AND WASTE DISCHARGE (LOW AND HIGH TEMPERATURE) WITHIN THE BUILDING STRUCTURE - ACRYLONITRILE-BUTADIENE-STYRENE (ABS) - PART 2: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY |
01/705811 DC : 0 | BS 5892-7 - RAILWAY ROLLING STOCK MATERIALS - PART 7: SPECIFICATION FOR CAST WHEELS FOR TRACTION AND TRAILING STOCK |
EN ISO/TS 15876-7 : 2003 | PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - POLYBUTYLENE (PB) - PART 7: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY |
S.R. CEN/TS 13598-3:2012 | PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE)(PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 3: GUIDANCE FOR ASSESSMENT OF CONFORMITY |
DD ENV 1401-2:2001 | Plastics piping systems for non-pressure underground drainage and sewerage. Unplasticized poly(vinylchloride) (PVC-U) Guidance for assessment of conformity |
UNI CEN/TS 1451-2 : 2012 | PLASTIC PIPING SYSTEMS FOR SOIL AND WASTE DISCHARGE (LOW AND HIGH TEMPERATURE) WITHIN THE BUILDING STRUCTURE - POLYPROPYLENE (PP) - PART 2: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY |
S.R. CEN/TS 1519-2:2012 | PLASTIC PIPING SYSTEMS FOR SOIL AND WASTE DISCHARGE (LOW AND HIGH TEMPERATURE) WITHIN THE BUILDING STRUCTURE - POLYETHYLEN (PE) - PART 2: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY |
I.S. EN 1279-6:2002 | GLASS IN BUILDING - INSULATING GLASS UNITS - PART 6: FACTORY PRODUCTION CONTROL AND PERIODIC TESTS |
DIN EN 1457-2:2016-10 (Draft) | Chimneys - Clay/ceramic flue liners - Part 2: Flue liners operating under wet conditions - Requirements and test methods; German and English version prEN 1457-2:2016 |
PREN 15655 : DRAFT 2016 | DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - INTERNAL POLYURETHANE LINING FOR PIPES AND FITTINGS - REQUIREMENTS AND TEST METHODS |
UNI EN 1457-2 : 2012 | CHIMNEYS - CLAY/CERAMIC FLUE LINERS - PART 2: FLUE LINERS OPERATING UNDER WET CONDITIONS - REQUIREMENTS AND TEST METHODS |
ISO/TS 15874-7:2003 | Plastics piping systems for hot and cold water installations Polypropylene (PP) Part 7: Guidance for the assessment of conformity |
ISO/TS 15876-7:2003 | Plastics piping systems for hot and cold water installations Polybutylene (PB) Part 7: Guidance for the assessment of conformity |
CEN ISO/TS 15875-7:2003 | Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 7: Guidance for the assessment of conformity (ISO/TS 15875-7:2003) |
I.S. EN 15655:2009 | DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - INTERNAL POLYURETHANE LINING FOR PIPES AND FITTINGS - REQUIREMENTS AND TEST METHODS |
I.S. EN 1917:2002 | CONCRETE MANHOLES AND INSPECTION CHAMBERS, UNREINFORCED, STEEL FIBRE AND REINFORCED |
DIN EN 1492-1:2009-05 | TEXTILE SLINGS - SAFETY - PART 1: FLAT WOVEN WEBBING SLINGS MADE OF MAN-MADE FIBRES FOR GENERAL PURPOSE USE |
DIN EN 1677-6:2009-03 | COMPONENTS FOR SLINGS - SAFETY - PART 6: LINKS - GRADE 4 |
DIN EN 681-1:2016-07 (Draft) | Elastomeric seals - Material requirements for pipe joint seals used in water and drainage applications - Part 1: Vulcanized rubber; German and English version prEN 681-1:2016 |
BS EN 1074-1:2000 | Valves for water supply. Fitness for purpose requirements and appropriate verification tests General requirements |
BS EN 13889 : 2003 | FORGED STEEL SHACKLES FOR GENERAL LIFTING PURPOSES - DEE SHACKLES AND BOW SHACKLES - GRADE 6 - SAFETY |
BS EN 545:2010 | Ductile iron pipes, fittings, accessories and their joints for water pipelines. Requirements and test methods |
BS EN 969:2009 | Ductile iron pipes, fittings, accessories and their joints for gas pipelines. Requirements and test methods |
BS EN 13069:2005 | Chimneys. Clay/ceramic outer walls for system chimneys. Requirements and test methods |
UNE-EN 12842:2013 | Ductile iron fittings for PVC-U or PE piping systems - Requirements and test methods |
BS EN 13411-6 : 2004 | TERMINATIONS FOR STEEL WIRE ROPES - SAFETY - PART 6: ASYMMETRIC WEDGE SOCKET |
EN 14408-1:2004 | Plastics piping systems for renovation of underground gas supply networks - Part 1: General |
UNI EN 1677-1 : 2009 | COMPONENTS FOR SLINGS - SAFETY - PART 1: FORGED STEEL COMPONENTS, GRADE 8 |
UNI EN 1917 : 2004 | CONCRETE MANHOLES AND INSPECTION CHAMBERS, UNREINFORCED, STEEL FIBRE AND REINFORCED |
UNI EN 1492-2 : 2009 | TEXTILE SLINGS - SAFETY - PART 2: ROUND SLINGS MADE OF MAN-MADE FIBRES FOR GENERAL PURPOSE USES |
UNI EN 1857 : 2010 | CHIMNEYS - COMPONENTS - CONCRETE FLUE LINERS |
UNI EN 1677-4 : 2009 | COMPONENTS FOR SLINGS - SAFETY - PART 4: LINKS, GRADE 8 |
UNI EN 13889 : 2009 | FORGED STEEL SHACKLES FOR GENERAL LIFTING PURPOSES - DEE SHACKLES AND BOW SHACKLES - GRADE 6: SAFETY |
UNI EN 15189 : 2007 | DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - EXTERNAL POLYURETHANE COATING FOR PIPES - REQUIREMENTS AND TEST METHODS |
UNI EN 14525 : 2005 | DUCTILE IRON WIDE TOLERANCE COUPLINGS AND FLANGE ADAPTORS FOR USE WITH PIPES OF DIFFERENT MATERIALS: DUCTILE IRON, GREY IRON, STEEL, PVC-U PE, FIBRE-CEMENT |
UNI EN 12842 : 2012 | DUCTILE IRON FITTINGS FOR PVC-U OR PE PIPING SYSTEMS - REQUIREMENTS AND TEST METHODS |
UNI EN 969 : 2009 | DUCTILE IRON PIPES, FITTINGS, ACCESSORIES AND THEIR JOINTS FOR GAS PIPELINES - REQUIREMENTS AND TEST METHODS |
I.S. EN 14525:2005 | DUCTILE IRON WIDE TOLERANCE COUPLINGS AND FLANGE ADAPTORS FOR USE WITH PIPES OF DIFFERENT MATERIALS: DUCTILE IRON, GREY IRON, STEEL, PVC-U PE, FIBRE-CEMENT |
UNI EN 14125 : 2013 | THERMOPLASTIC AND FLEXIBLE METAL PIPEWORK FOR UNDERGROUND INSTALLATION AT PETROL FILLING STATIONS |
UNI EN 13411-6 : 2009 | TERMINATIONS FOR STEEL WIRE ROPES - SAFETY - PART 6: ASYMMETRIC WEDGE SOCKET |
UNI EN 545 : 2010 | DUCTILE IRON PIPES, FITTINGS, ACCESSORIES AND THEIR JOINTS FOR WATER PIPELINES - REQUIREMENTS AND TEST METHODS |
EN 45011:1998 | General requirements for bodies operating product certification systems (ISO/IEC Guide 65:1996) |
UNI EN 1492-1 : 2009 | TEXTILE SLINGS - SAFETY - PART 1: FLAT WOVEN WEBBING SLINGS MADE OF MAN-MADE FIBRES FOR GENERAL PURPOSE USES |
UNI EN 1916 : 2004 | CONCRETE PIPES AND FITTINGS, UNREINFORCED, STEEL FIBRE AND REINFORCED |
UNI EN 1677-5 : 2009 | COMPONENTS FOR SLINGS - SAFETY - PART 5: FORGED STEEL LIFTING HOOKS WITH LATCH - GRADE 4 |
04/30111056 DC : DRAFT MARCH 2004 | EN 1806 - CHIMNEYS - CLAY/CERAMIC FLUE BLOCKS FOR SINGLE WALL CHIMNEYS - REQUIREMENTS AND TEST METHODS |
SBAC TS 157 : 6 | AEROSPACE SECTOR CERTIFICATION SCHEME (ASCS) - REQUIREMENTS AND PROCEDURES |
DD CEN/TS 14758-2:2007 | Plastics piping systems for non-pressure underground drainage and sewerage. Polypropylene with mineral modifier(s) (PP-MD) Guidance for the assessment of conformity |
I.S. EN 14408-1:2004 | PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND GAS SUPPLY NETWORKS - PART 1: GENERAL |
PREN 14125 : DRAFT 2011 | THERMOPLASTIC AND FLEXIBLE METAL PIPEWORK FOR UNDERGROUND INSTALLATION AT PETROL FILLING STATIONS |
I.S. EN 45011:1998 | GENERAL REQUIREMENTS FOR BODIES OPERATING PRODUCT CERTIFICATION SYSTEMS |
08/30183125 DC : 0 | BS EN 1857 - CHIMNEYS - COMPONENTS - CONCRETE FLUE LINERS |
UNI CEN/TS 1555-7 : 2013 | PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 7: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY |
DD CEN/TS 12666-2:2005 | Plastics piping systems for non-pressure underground drainage and sewerage. Polyethylene (PE) Guidance for the assessment of conformity |
PD CEN/TS 1519-2:2012 | Plastic piping systems for soil and waste discharge (low and high temperature) within the building structure. Polyethylen (PE) Guidance for the assessment of conformity |
07/30156488 DC : 0 | EN 15655 - DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - INTERNAL POLYURETHANE LINING FOR PIPES AND FITTINGS - REQUIREMENTS AND TEST METHODS |
BS EN 15655:2009 | Ductile iron pipes, fittings and accessories. Internal polyurethane lining for pipes and fittings. Requirements and test methods |
01/108876 DC : DRAFT DEC 2001 | PREN 1317-5 - ROAD RESTRAINT SYSTEMS - PART 5: PRODUCT REQUIREMENTS, DURABILITY AND EVALUATION OF CONFORMITY |
01/704739 DC : DRAFT FEB 2001 | PREN 14125 - UNDERGROUND PIPEWORK FOR PETROL FILLING STATIONS |
BS EN 1457-2:2012 | Chimneys. Clay/ceramic flue liners Flue liners operating under wet conditions. Requirements and test methods |
DD CEN ISO/TS 15874-7:2003 | Plastics piping systems for hot and cold water installations. Polypropylene (PP) Guidance for the assessment of conformity |
DD CEN ISO/TS 15875-7:2003 | Plastics piping systems for hot and cold water installations. Crosslinked polyethylene (PE-X) Guidance for the assessment of conformity |
95/105293 DC : DRAFT JUL 95 | GLASS IN BUILDING - INSULATING GLASS UNITS - PART 1: GENERALITIES AND DIMENSIONAL TOLERANCES |
BS 8404:2001 | Packaging. Child-resistant packaging. Requirements and testing procedures for non-reclosable packages for pharmaceutical products |
DD ENV 1565-2:2001 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Styrene copolymer blends (SAN + PVC) Guidance for the assessment of conformity |
UNI CEN/TS 13598-3 : 2012 | PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 3: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY |
16/30338240 DC | BS EN 1457-1. Chimney. Clay/ceramic flue liners. Part 1. Flue liners operating under dry conditions. Requirements and test methods |
S.R. CEN/TS 13476-4:2013 | PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 4: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY |
I.S. CWA 14172-1:2004 | EESSI CONFORMITY ASSESSMENT GUIDANCE - PART 1: GENERAL INTRODUCTION |
ISO 10381-1:2002 | Soil quality Sampling Part 1: Guidance on the design of sampling programmes |
I.S. EN ISO/TS 15875-7:2004 | PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - CROSSLINKED POLYETHYLENE (PE-X) - PART 7: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY |
DD CEN/TS 12200-2:2003 | Plastics rainwater piping systems for above ground external use. Unplasticized poly (vinyl chloride) (PVC-U) Guidance for the assessment of conformity |
I.S. CWA 14172-6:2004 | EESSI CONFORMITY ASSESSMENT GUIDANCE - PART 6: SIGNATURE-CREATION DEVICE SUPPORTING SIGNATURES OTHER THAN QUALIFIED |
I.S. CWA 14172-8:2004 | EESSI CONFORMITY ASSESSMENT GUIDANCE - PART 8: TIME-STAMPING AUTHORITY SERVICES AND PROCESSES |
I.S. CEN TS 12201-7:2003 | PLASTICS PIPING SYSTEMS FOR WATER SUPPLY - POLYETHYLENE (PE) - PART 7: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY |
DIN EN 10242:1995-03 | THREADED PIPE FITTING IN MALLEABLE CAST IRON |
DIN EN 969:2009-07 | DUCTILE IRON PIPES, FITTINGS, ACCESSORIES AND THEIR JOINTS FOR GAS PIPELINES - REQUIREMENTS AND TEST METHODS |
ISO/IEC Guide 65:1996 | General requirements for bodies operating product certification systems |
BS EN 10284:2000 | Malleable cast iron fittings with compression ends for polyethylene (PE) piping systems |
UNE-EN 1857:2013 | Chimneys - Components - Concrete flue liners |
BS EN 805:2000 | Water supply. Requirements for systems and components outside buildings |
BS EN 1677-1 : 2000 | COMPONENTS FOR SLINGS - SAFETY - PART 1: FORGED STEEL COMPONENTS, GRADE 8 |
BS EN 1293:1999 | General requirements for components used in pneumatically pressurized discharge pipes, drains and sewers |
BS EN 1806:2006 | Chimneys Clay/ceramic flue blocks for single wall chimneys Requirements and test methods |
BS EN 773:1999 | General requirements for components used in hydraulically pressurized discharge pipes, drains and sewers |
BS EN 1857 : 2003 | CHIMNEYS - COMPONENTS - CONCRETE FLUE LINERS |
BS EN 14409-1:2004 | Plastics piping systems for renovation of underground water supply networks General |
BS EN 13411-7 : 2006 | TERMINATIONS FOR STEEL WIRE ROPES - SAFETY - PART 7: SYMMETRIC WEDGE SOCKET |
UNE-EN 14125:2013 | Thermoplastic and flexible metal pipework for underground installation at petrol filling stations |
BS EN 1677-5 : 2001 | COMPONENTS FOR SLINGS - SAFETY - PART 5: FORGED STEEL LIFTING HOOKS WITH LATCH - GRADE 4 |
BS EN 15189:2006 | Ductile iron pipes, fittings and accessories. External polyurethane coating for pipes. Requirements and test methods |
BS EN 12094-9:2003 | Fixed firefighting systems. Components for gas extinguishing systems Requirements and test methods for special fire detectors |
BS EN 14125:2013 | Thermoplastic and flexible metal pipework for underground installation at petrol filling stations |
BS EN 1677-4 : 2000 | COMPONENTS FOR SLINGS - SAFETY - PART 4: LINKS, GRADE 8 |
BS EN 12408:2004 | Safety requirements for cableways installations designed to carry person. Quality control |
CEN/TS 1401-2:2012 | Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U) - Part 2: Guidance for assessment of conformity |
BS EN 1917:2002 | Concrete manholes and inspection chambers, unreinforced, steel fibre and reinforced |
EN 14409-1:2004 | Plastics piping systems for renovation of underground water supply networks - Part 1: General |
EN 14628:2005 | Ductile iron pipes, fittings and accessories - External polyethylene coating for pipes - Requirements and test methods |
EN 1677-5:2001+A1:2008 | Components for slings - Safety - Part 5: Forged steel lifting hooks with latch - Grade 4 |
EN 15189:2006 | Ductile iron pipes, fittings and accessories - External polyurethane coating for pipes - Requirements and test methods |
EN 773:1999 | General requirements for components used in hydraulically pressurized discharge pipes, drains and sewers |
EN 1677-6:2001+A1:2008 | Components for slings - Safety - Part 6: Links - Grade 4 |
EN 13980:2002 | Potentially explosive atmospheres - Application of quality systems |
EN 969:2009 | Ductile iron pipes, fittings, accessories and their joints for gas pipelines - Requirements and test methods |
EN 13889:2003+A1:2008 | Forged steel shackles for general lifting purposes - Dee shackles and bow shackles - Grade 6 - Safety |
CEN/TS 1565-2:2012 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Styrene-copolymer blends (SAN+PVC) - Part 2: Guidance for the assessment of conformity |
EN 1857:2010 | Chimneys - Components - Concrete flue liners |
EN 14525:2004 | Ductile iron wide tolerance couplings and flange adaptors for use with pipes of different materials: ductile iron, Grey iron, Steel, PVC-U PE, Fibre-cement |
EN 14125:2013 | Thermoplastic and flexible metal pipework for underground installation at petrol filling stations |
EN 1492-2:2000+A1:2008 | Textile slings - Safety - Part 2: Roundslings made of man-made fibres for general purpose use |
EN ISO/TS 15877-7 : 2003 | PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - CHLORINATED POLY(VINYL CHLORIDE) (PVC-C) - PART 7: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY |
EN 1457-1:2012 | Chimneys - Clay/ceramic flue liners - Part 1: Flue liners operating under dry conditions - Requirements and test methods |
EN 805:2000 | Water supply - Requirements for systems and components outside buildings |
EN 12842:2012 | Ductile iron fittings for PVC-U or PE piping systems - Requirements and test methods |
EN 1677-4:2000+A1:2008 | Components for slings - Safety - Part 4: Links, Grade 8 |
EN 1492-1:2000+A1:2008 | Textile slings - Safety - Part 1: Flat woven webbing slings made of man-made fibres for general purpose use |
EN 1457-2:2012 | Chimneys - Clay/ceramic flue liners - Part 2: Flue liners operating under wet conditions - Requirements and test methods |
EN 1677-1:2000+A1:2008 | Components for slings - Safety - Part 1: Forged steel components, Grade 8 |
EN 1806:2006 | Chimneys - Clay/ceramic flue blocks for single wall chimneys - Requirements and test methods |
05/30131069 DC : DRAFT MAR 2005 | EN 598:2005 - DUCTILE IRON PIPES, FITTINGS, ACCESSORIES AND THEIR JOINTS FOR SEWERAGE APPLICATIONS - REQUIREMENTS AND TEST METHODS |
I.S. CEN TS 14632:2006 | PLASTICS PIPING SYSTEMS FOR DRAINAGE, SEWERAGE AND WATER SUPPLY, PRESSURE AND NON-PRESSURE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON POLYESTER RESIN (UP) - GUIDANCE FOR THE ASSESSMENT OF CONFORMITY |
I.S. EN 14409-1:2004 | PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND WATER SUPPLY NETWORKS - PART 1: GENERAL |
PD CEN/TS 14632:2012 | Plastics piping systems for drainage, sewerage and water supply, pressure and non-pressure. Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP). Guidance for the assessment of conformity |
DD CEN/TS 13244-7:2003 | Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage. Polyethylene (PE) Guidance for the assessment of conformity |
I.S. EN ISO/TS 15874-7:2004 | PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS POLYPROPYLENE (PP) - PART 7: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY |
08/30181473 DC : DRAFT JULY 2008 | BS EN 545 - DUCTILE IRON PIPES, FITTINGS, ACCESSORIES AND THEIR JOINTS FOR WATER PIPELINES - REQUIREMENTS AND TEST METHODS |
DD CEN/TS 1555-7:2003 | Plastics piping systems for the supply of gaseous fuels. Polyethylene (PE) Guidance for the assessment of conformity |
PD CEN/TS 1565-2:2012 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Styrene-copolymer blends (SAN+PVC) Guidance for the assessment of conformity |
06/19977015 DC : DRAFT JULY 2006 | BS EN 10344 - MALLEABLE CAST IRON FITTINGS WITH COMPRESSION ENDS FOR STEEL PIPES |
BS ISO 10381-1:2002 | Soil quality. Sampling Guidance on the design of sampling programmes |
BS EN 1457-1:2012 | Chimneys. Clay/ceramic flue liners Flue liners operating under dry conditions. Requirements and test methods |
97/102206 DC : DRAFT MAR 1997 | PREN 12794 - PRECAST CONCRETE FOUNDATION PILES |
BS EN 1279-6:2002 | Glass in building. Insulating glass units Factory production control and periodic tests |
I.S. CEN TS 12200-2:2003 | PLASTICS RAINWATER PIPING SYSTEMS FOR ABOVE GROUND EXTERNAL USE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) - PART 2: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY |
S.R. CEN/TS 1555-7:2013 | PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 7: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY |
I.S. CEN TS 1456-2:2003 | PLASTICS PIPING SYSTEMS FOR BURIED AND ABOVE-GROUND DRAINAGE AND SEWERAGE UNDER PRESSURE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) - PART 2: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY |
I.S. CEN TS 13244-7:2003 | PLASTICS PIPING SYSTEMS FOR BURIED AND ABOVE-GROUND PRESSURE SYSTEMS FOR WATER FOR GENERAL PURPOSES, DRAINAGE AND SEWERAGE - POLYETHYLENE (PE) - PART 7: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY |
I.S. EN CWA 14172-5:2004 | EESSI CONFORMITY ASSESSMENT GUIDANCE - PART 5: SECURE SIGNATURE CREATION DEVICES |
S.R. CEN/TS 1451-2:2012 | PLASTIC PIPING SYSTEMS FOR SOIL AND WASTE DISCHARGE (LOW AND HIGH TEMPERATURE) WITHIN THE BUILDING STRUCTURE - POLYPROPYLENE (PP) - PART 2: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY |
DIN EN 1457-1:2016-10 (Draft) | Chimney - Clay/ceramic flue liners - Part 1: Flue liners operating under dry conditions - Requirements and test methods; German and English version prEN 1457-1:2016 |
PD CEN/TS 1329-2:2012 | Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Unplasticized poly(vinyl chloride) (PVC-U) Guidance for the assessment of conformity |
DD CEN ISO/TS 15876-7:2003 | Plastics piping systems for hot and cold water installations. Polybutylene (PB) Guidance for the assessment of conformity |
ISO 18400-106:2017 | Soil quality — Sampling — Part 106: Quality control and quality assurance |
UNI CEN/TS 1401-2 : 2012 | PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGRONUD DRAINAGE AND SEWERAGE - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) - PART 2: GUIDANCE FOR ASSESSMENT OF CONFORMITY |
EN 15655:2009 | Ductile iron pipes, fittings and accessories - Internal polyurethane lining for pipes and fittings - Requirements and test methods |
I.S. EN ISO/TS 15877-7:2004 | PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - CHLORINATED POLY(VINYL CHLORIDE) (PVC-C) - PART 7: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY |
DIN EN 14125:2013-09 | THERMOPLASTIC AND FLEXIBLE METAL PIPEWORK FOR UNDERGROUND INSTALLATION AT PETROL FILLING STATIONS |
BS EN 1916:2002 | Concrete pipes and fittings, unreinforced, steel fibre and reinforced |
BS EN 1492-1 : 2000 | TEXTILE SLINGS - SAFETY - PART 1: FLAT WOVEN WEBBING SLINGS MADE OF MAN-MADE FIBRES FOR GENERAL PURPOSE USE |
BS EN 12842:2012 | Ductile iron fittings for PVC-U or PE piping systems. Requirements and test methods |
BS EN 1677-6 : 2001 | COMPONENTS FOR SLINGS - SAFETY - PART 6: LINKS - GRADE 4 |
BS EN 13566-1:2002 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks General |
CEN/TS 1451-2:2012 | Plastic piping systems for soil and waste discharge (low and high temperature) within the building structure - Polypropylene (PP) - Part 2: Guidance for the assessment of conformity |
EN 10284:2000 | Malleable cast iron fittings with compression ends for polyethylene (PE) piping systems |
DIN EN 13411-6:2009-04 | TERMINATIONS FOR STEEL WIRE ROPES - SAFETY - PART 6: ASYMMETRIC WEDGE SOCKET |
EN 13566-1:2002 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 1: General |
CEN/TS 13244-7 : 2003 | PLASTICS PIPING SYSTEMS FOR BURIED AND ABOVE-GROUND PRESSURE SYSTEMS FOR WATER FOR GENERAL PURPOSES, DRAINAGE AND SEWERAGE - POLYETHYLENE (PE) - PART 7: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY |
DIN EN 14525:2005-02 | Ductile iron wide tolerance couplings and flange adaptors for use with pipes of different materials: Ductile iron, grey iron, steel, PVC-U, PE, fibre-cement |
EN 1074-1:2000 | Valves for water supply - Fitness for purpose requirements and appropriate verification tests - Part 1: General requirements |
EN 13380:2001 | General requirements for components used for renovation and repair of drain and sewer systems outside buildings |
CEN/TS 1555-7:2013 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 7: Guidance for the assessment of conformity |
EN 12094-9:2003 | Fixed firefighting systems - Components for gas extinguishing systems - Part 9: Requirements and test methods for special fire detectors |
DIN EN 545:2011-09 | Ductile iron pipes, fittings, accessories and their joints for water pipelines - Requirements and test methods |
DIN EN 13411-7:2009-04 | Terminations for steel wire ropes - Safety - Part 7: Symmetric wedge socket (includes Amendment A1:2008) |
DIN EN 1457-1:2012-04 | Chimneys - Clay/ceramic flue liners - Part 1: Flue liners operating under dry conditions - Requirements and test methods |
DIN EN 1457-2:2012-04 | Chimneys - Clay/ceramic flue liners - Part 2: Flue liners operating under wet conditions - Requirements and test methods |
DIN EN 13980:2003-02 | POTENTIALLY EXPLOSIVE ATMOSPHERES - APPLICATION OF QUALITY SYSTEMS |
CEN/TS 14632:2012 | Plastics piping systems for drainage, sewerage and water supply, pressure and non-pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Guidance for the assessment of conformity |
DIN EN 14628:2006-01 | DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - EXTERNAL POLYETHYLENE COATING FOR PIPES - REQUIREMENTS AND TEST METHODS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.