EN 16282-7:2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Equipment for commercial kitchens - Components for ventilation in commercial kitchens - Part 7: Installation and use of fixed fire suppression systems
05-21-2021
07-26-2017
European foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Fire hazard/Fire load
5 Safety requirements
6 Hygienic requirement
7 Service and maintenance
8 Installation
9 Marking
Bibliography
This European Standard specifies requirements and gives recommendations for the design, installation, testing, maintenance and safety of kitchen fire suppression systems in buildings.This European Standard is applicable to ventilation systems in commercial kitchens, associated areas and other installations processing foodstuffs intended for commercial use. Kitchens and associated areas are special rooms in which meals are prepared, where tableware and equipment is washed, cleaned, food is stored and food waste areas.This European Standard is applicable to fire suppression systems except those used in domestic kitchens or industrial food processing facilities.Unless otherwise specified, the requirements of this standard should be checked by way of inspection and/or measurement.NOTEPlease note the possible existence of additional or alternative local national regulations on installation, appliance requirements and inspection, maintenance and operation.
Committee |
CEN/TC 156
|
DevelopmentNote |
Supersedes PREN 16282-7. (08/2017)
|
DocumentType |
Standard
|
PublisherName |
Comite Europeen de Normalisation
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
Standards | Relationship |
NS EN 16282-7 : 2017 | Identical |
I.S. EN 16282-7:2017 | Identical |
UNE-EN 16282-7:2018 | Identical |
NF EN 16282-7 : 2017 | Identical |
SN EN 16282-7 : 2017 | Identical |
PN EN 16282-7 : 2017 | Identical |
BS EN 16282-7:2017 | Identical |
NEN EN 16282-7 : 2017 | Identical |
DIN EN 16282-7:2017-12 | Identical |
ONORM EN 16282-7 : 2017 | Identical |
EN 16282-1:2017 | Equipment for commercial kitchens - Components for ventilation in commercial kitchens - Part 1: General requirements including calculation method |
BS EN 16282-8:2017 | Equipment for commercial kitchens. Components for ventilation in commercial kitchens Installations for treatment of aerosol. Requirements and testing |
I.S. EN 16282-1:2017 | EQUIPMENT FOR COMMERCIAL KITCHENS - COMPONENTS FOR VENTILATION IN COMMERCIAL KITCHENS - PART 1: GENERAL REQUIREMENTS INCLUDING CALCULATION METHOD |
I.S. EN 16282-8:2017 | EQUIPMENT FOR COMMERCIAL KITCHENS - COMPONENTS FOR VENTILATION IN COMMERCIAL KITCHENS - PART 8: INSTALLATIONS FOR TREATMENT OF AEROSOL - REQUIREMENTS AND TESTING |
BS EN 16282-1:2017 | Equipment for commercial kitchens. Components for ventilation in commercial kitchens General requirements including calculation method |
EN 16282-8:2017 | Equipment for commercial kitchens - Components for ventilation in commercial kitchens - Part 8: Installations for treatment of aerosol; Requirements and testing |
EN 615:2009 | Fire protection - Fire extinguishing media - Specifications for powders (other than class D powders) |
EN ISO 7250-1:2017 | Basic human body measurements for technological design - Part 1: Body measurement definitions and landmarks (ISO 7250-1:2017) |
EN 894-3:2000+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 3: Control actuators |
EN 547-2:1996+A1:2008 | Safety of machinery - Human body measurements - Part 2: Principles for determining the dimensions required for access openings |
EN 547-1:1996+A1:2008 | Safety of machinery - Human body measurements - Part 1: Principles for determining the dimensions required for openings for whole body access into machinery |
EN 16282-5:2017 | Equipment for commercial kitchens - Components for ventilation in commercial kitchens - Part 5: Air duct; Design and dimensioning |
EN ISO 13857:2008 | Safety of machinery - Safety distances to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2008) |
ISO 12100:2010 | Safety of machinery — General principles for design — Risk assessment and risk reduction |
PREN 16282-6 : DRAFT 2014 | EQUIPMENT FOR COMMERCIAL KITCHENS - COMPONENTS FOR VENTILATION OF COMMERCIAL KITCHENS - PART 6: AEROSOL SEPARATORS; DESIGN AND SAFETY REQUIREMENTS |
ISO 7250-1:2017 | Basic human body measurements for technological design — Part 1: Body measurement definitions and landmarks |
EN 547-3:1996+A1:2008 | Safety of machinery - Human body measurements - Part 3: Anthropometric data |
ISO 13857:2008 | Safety of machinery Safety distances to prevent hazard zones being reached by upper and lower limbs |
EN ISO 12100:2010 | Safety of machinery - General principles for design - Risk assessment and risk reduction (ISO 12100:2010) |
EN 61140:2016 | Protection against electric shock - Common aspects for installation and equipment |
EN 1846-1:2011 | Firefighting and rescue service vehicles - Part 1: Nomenclature and designation |
EN 60335-1:2012/A13:2017 | HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60335-1:2010, MODIFIED) |
EN 16282-1:2017 | Equipment for commercial kitchens - Components for ventilation in commercial kitchens - Part 1: General requirements including calculation method |
EN 16282-8:2017 | Equipment for commercial kitchens - Components for ventilation in commercial kitchens - Part 8: Installations for treatment of aerosol; Requirements and testing |
IEC 61140:2016 | Protection against electric shock - Common aspects for installation and equipment |
EN 10088-1:2014 | Stainless steels - Part 1: List of stainless steels |
1997/23/EC : 1997 | DIRECTIVE 97/23/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 29 MAY 1997 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES CONCERNING PRESSURE EQUIPMENT |
EN 60204-1 : 2006 COR 2010 | SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.