EN 15266:2007
Current
The latest, up-to-date edition.
Stainless steel pliable corrugated tubing kits in buildings for gas with an operating pressure up to 0,5 bar
05-09-2007
Foreword
Introduction
1 Scope
2 Normative references
3 Terms, definitions and abbreviations
4 Design requirements
4.1 General
4.2 Materials
4.3 Nominal size DN and pressure drop
4.4 Threads
4.5 PLT fittings
4.6 Seals and sealing agents
4.7 Environment
4.8 Supports
4.9 Electrical conductivity requirements
4.10 Cover
5 Performance and test requirements
5.1 General
5.2 Tightness
5.3 Dimensional check
5.4 Bending performance
5.5 Crushing resistance
5.6 Stability under pressure
5.7 Wear resistance of outer cover
5.8 Structural strength test
5.9 Impact resistance
5.10 Penetration resistance
5.11 Resistance to pull out
5.12 Chemical resistance
5.13 Low temperature resistance
5.14 Ageing
5.15 Tightness in case of fire
5.16 Reaction to fire
5.17 Electrical conductivity
5.18 Pressure drop
5.19 Maximum load for admissible deformation of PLT
support
5.20 Dangerous substances
6 Evaluation of conformity
6.1 General
6.2 Type testing
6.3 Factory production control (FPC)
6.4 Assembly and installation instruction
6.5 Marking, labelling and packaging
Annex A (normative) Single-flame source test
A.1 General
A.2 Standardised mounting and fixing
A.3 Test definition
A.4 Test duration
Annex B (normative) Thermal attack by a single burning
item
B.1 General
B.2 Standardised mounting and fixing
Annex ZA (informative) Clauses of this European Standard
addressing the provisions of the EU Construction
Products Directive (89/106/EEC)
ZA.1 Scope and relevant characteristics
ZA.2 Procedure for attestation of conformity of stainless
steel pliable corrugated gas tubing kits
ZA.2.2 EC Certificate and declaration of conformity
ZA.3 CE marking and labeling
Bibliography
This European Standard specifies the requirements for material, design, manufacture, testing, marking and documentation of stainless steel pliable corrugated gas tubing kits for buildings with a maximum operating pressure (MOP) less than or equal to 0,5 bar and a nominal size range from DN 10 to DN 50.This document applies to stainless steel pliable corrugated gas tubing kits used for 1st, 2nd and 3rd family gases in residential, commercial and industrial gas installations.This document does not apply to:pliable tubing without cover;corrugated safety metal hose assemblies for connection to moveable appliances.This document does not cover the installation aspects of stainless steel pliable corrugated gas tubing kits.
| Committee |
CEN/TC 342
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Current
|
| Standards | Relationship |
| NEN EN 15266 : 2007 | Identical |
| I.S. EN 15266:2007 | Identical |
| NF EN 15266 : 2007 | Identical |
| BS EN 15266:2007 | Identical |
| UNI EN 15266 : 2007 | Identical |
| NS EN 15266 : 1ED 2007 | Identical |
| UNE-EN 15266:2008 | Identical |
| DIN EN 15266:2007-08 | Identical |
| SN EN 15266 : 2007 | Identical |
| PN EN 15266 : 2009 | Identical |
| NBN EN 15266 : 2007 | Identical |
| 17/30363953 DC : 0 | BS EN 416 - GAS-FIRED OVERHEAD RADIANT TUBE HEATERS AND RADIANT TUBE HEATER SYSTEMS FOR NON-DOMESTIC USE - SAFETY AND ENERGY EFFICIENCY |
| 12/30259203 DC : 0 | BS EN 12007-5 - GAS INFRASTRUCTURE - PIPELINES FOR MAXIMUM OPERATING PRESSURE UP TO AND INCLUDING 16 BAR - PART 5: SERVICE LINES, SPECIFIC FUNCTIONAL REQUIREMENTS |
| EN 12007-5:2014 | Gas infrastructure - Pipelines for maximum operating pressure up to and including 16 bar - Part 5: Service lines - Specific functional requirements |
| PREN 416 : DRAFT 2017 | GAS-FIRED OVERHEAD RADIANT TUBE HEATERS AND RADIANT TUBE HEATER SYSTEMS FOR NON-DOMESTIC USE - SAFETY AND ENERGY EFFICIENCY |
| BS EN 12007-5:2014 | Gas infrastructure. Pipelines for maximum operating pressure up to and including 16 bar Service lines. Specific functional requirements |
| PREN 17175 : DRAFT 2017 | GAS-FIRED OVERHEAD RADIANT STRIP HEATERS AND MULTI-BURNER CONTINUOUS RADIANT TUBE HEATER SYSTEMS FOR NON-DOMESTIC USE - SAFETY AND ENERGY EFFICIENCY |
| UNI EN 12007-5 : 2014 | GAS INFRASTRUCTURE - PIPELINES FOR MAXIMUM OPERATING PRESSURE UP TO AND INCLUDING 16 BAR - PART 5: SERVICE LINES - SPECIFIC FUNCTIONAL REQUIREMENTS |
| BS EN ISO 10239:2017 | Small craft. Liquefied petroleum gas (LPG) systems |
| I.S. EN 12007-5:2014 | GAS INFRASTRUCTURE - PIPELINES FOR MAXIMUM OPERATING PRESSURE UP TO AND INCLUDING 16 BAR - PART 5: SERVICE LINES - SPECIFIC FUNCTIONAL REQUIREMENTS |
| UNE-EN ISO 10239:2017 | Small craft - Liquefied petroleum gas (LPG) systems (ISO 10239:2014) |
| DIN EN 1775:2007-10 | Gas supply - Gas pipework for buildings - Maximum operating pressure less than or equal to 5 bar - Functional recommendations |
| I.S. EN 1775:2007 | GAS SUPPLY - GAS PIPEWORK FOR BUILDINGS - MAXIMUM OPERATING PRESSURE LESS THAN OR EQUAL TO 5 BAR - FUNCTIONAL RECOMMENDATIONS |
| DIN EN 12007-5:2014-07 | GAS INFRASTRUCTURE - PIPELINES FOR MAXIMIUM OPERATING PRESSURE UP TO AND INCLUDING 16 BAR - PART 5: SERVICE LINES - SPECIFIC FUNCTIONAL REQUIREMENTS |
| ISO 10239:2014 | Small craft Liquefied petroleum gas (LPG) systems |
| I.S. EN ISO 10239:2017 | SMALL CRAFT - LIQUEFIED PETROLEUM GAS (LPG) SYSTEMS (ISO 10239:2014) |
| UNI EN 1775 : 2007 | GAS SUPPLY - GAS PIPEWORK FOR BUILDINGS - MAXIMUM OPERATING PRESSURE LESS THAN OR EQUAL TO 5 BAR - FUNCTIONAL RECOMMENDATIONS |
| 13/30261510 DC : 0 | BS EN ISO 10239 - SMALL CRAFT - LIQUEFIED PETROLEUM GAS (LPG) SYSTEMS |
| 17/30363959 DC : 0 | BS EN 17175 - GAS-FIRED OVERHEAD RADIANT STRIP HEATERS AND MULTI-BURNER CONTINUOUS RADIANT TUBE HEATER SYSTEMS FOR NON-DOMESTIC USE - SAFETY AND ENERGY EFFICIENCY |
| EN 1775:2007 | Gas supply - Gas pipework for buildings - Maximum operating pressure less than or equal to 5 bar - Functional recommendations |
| EN ISO 10239:2017 | Small craft - Liquefied petroleum gas (LPG) systems (ISO 10239:2014) |
| DIN EN ISO 10239:2015-05 | SMALL CRAFT - LIQUEFIED PETROLEUM GAS (LPG) SYSTEMS (ISO 10239:2014) |
| DIN EN 12007-5 E : 2014 | GAS INFRASTRUCTURE - PIPELINES FOR MAXIMUM OPERATING PRESSURE UP TO AND INCLUDING 16 BAR - PART 5: SERVICE LINES - SPECIFIC FUNCTIONAL REQUIREMENTS |
| S.R. 12007-5:2016 | GUIDANCE ON THE APPLICATION OF I.S. EN 12007-5:2014, GAS INFRASTRUCTURE - PIPELINES FOR MAXIMUM OPERATING PRESSURE UP TO AND INCLUDING 16 BAR - PART 5: SERVICE LINES - SPECIFIC FUNCTIONAL REQUIREMENTS |
| BS EN 1775:2007 | Gas supply. Gas pipework for buildings. Maximum operating pressure less than or equal to 5 bar. Functional recommendations |
| EN 1775:2007 | Gas supply - Gas pipework for buildings - Maximum operating pressure less than or equal to 5 bar - Functional recommendations |
| 89/106/EEC : 1988 | COUNCIL DIRECTIVE OF 21 DECEMBER 1988 ON THE APPROXIMATION OF LAWS, REGULATIONS AND ADMINISTRATIVE PROVISIONS OF THE MEMBER STATES RELATING TO CONSTRUCTION PRODUCTS |
| EN 10088-3:2014 | Stainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes |
| EN 751-2:1996 | Sealing materials for metallic threaded joints in contact with 1st, 2nd and 3rd family gases and hot water - Part 2: Non-hardening jointing compounds |
| ISO 11925-2:2010 | Reaction to fire tests Ignitability of products subjected to direct impingement of flame Part 2: Single-flame source test |
| EN ISO 9227:2017 | Corrosion tests in artificial atmospheres - Salt spray tests (ISO 9227:2017) |
| EN 13823:2010+A1:2014 | Reaction to fire tests for building products - Building products excluding floorings exposed to the thermal attack by a single burning item |
| EN 10028-7:2016 | Flat products made of steels for pressure purposes - Part 7: Stainless steels |
| EN ISO 10380:2012 | Pipework - Corrugated metal hoses and hose assemblies (ISO 10380:2012) |
| ISO 10380:2012 | Pipework — Corrugated metal hoses and hose assemblies |
| EN 437:2003+A1:2009 | Test gases - Test pressures - Appliance categories |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| ISO 6509:1981 | Corrosion of metals and alloys Determination of dezincification resistance of brass |
| ISO 9001:2015 | Quality management systems — Requirements |
| EN 751-1:1996 | Sealing materials for metallic threaded joints in contact with 1st, 2nd and 3rd family gases and hot water - Part 1: Anaerobic jointing compounds |
| EN 12164:2016 | Copper and copper alloys - Rod for free machining purposes |
| EN 1363-1:2012 | Fire resistance tests - Part 1: General Requirements |
| ISO 9227:2017 | Corrosion tests in artificial atmospheres — Salt spray tests |
| EN 549:1994 | Rubber materials for seals and diaphragms for gas appliances and gas equipment |
| ISO 7369:2004 | Pipework Metal hoses and hose assemblies Vocabulary |
| EN ISO 6509:1995 | Corrosion of metals and alloys - Determination of dezincification resistance of brass (ISO 6509:1981) |
| EN 12165:2016 | Copper and copper alloys - Wrought and unwrought forging stock |
| EN 10226-1:2004 | Pipe threads where pressure tight joints are made on the threads - Part 1: Taper external threads and parallel internal threads - Dimensions, tolerances and designation |
| ISO 6957:1988 | Copper alloys Ammonia test for stress corrosion resistance |
| EN ISO 7369:2004 | Pipework - Metal hoses and hose assemblies - Vocabulary (ISO 7369:2004) |
| EN 10088-1:2014 | Stainless steels - Part 1: List of stainless steels |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.