EN 14466:2005+A1:2008

Foreword
0 Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of significant hazards
5 Requirements
  5.1 Safety requirements and/or protective measures
      5.1.1 General
      5.1.2 Mechanical devices
      5.1.3 Electrical facilities
      5.1.4 Thermal hazards
      5.1.5 Noise
      5.1.6 Hazards generated by materials and substances
      5.1.7 Ergonomic design principles
      5.1.8 Overspeed protection
      5.1.9 Stopping device
      5.1.10 Indication of limit pressure (p[a lim])
      5.1.11 Special tools
  5.2 Performance requirements
      5.2.1 General
      5.2.2 Hydraulic performance
      5.2.3 Vibration during operation
      5.2.4 Inclination
      5.2.5 Cold start
      5.2.6 Clutch
      5.2.7 Generator
      5.2.8 Cooling system
      5.2.9 Starting device
      5.2.10 Fuel system
      5.2.11 Corrosion
      5.2.12 Priming time
      5.2.13 Operating controls and instrumentation
      5.2.14 Number of delivery outlets
6 Verification
  6.1 Verification of safety requirements and/or measures
      6.1.1 General
      6.1.2 Mechanical devices
      6.1.3 Electrical facilities
      6.1.4 Thermal hazards
      6.1.5 Noise
      6.1.6 Hazards generated by materials and substances
      6.1.7 Ergonomic principles
      6.1.8 Overspeed protection
      6.1.9 Stopping device
      6.1.10 Indication of limit pressure (p[a lim])
      6.1.11 Special tools
  6.2 Verification of performance requirements
      6.2.1 General
      6.2.2 Hydraulic performance
      6.2.3 Vibration during operation
      6.2.4 Inclination
      6.2.5 Cold start
      6.2.6 Clutch
      6.2.7 Generator
      6.2.8 Cooling system
      6.2.9 Starting device
      6.2.10 Fuel system
      6.2.11 Corrosion
      6.2.12 Priming time
      6.2.13 Operating controls and instrumentation
      6.2.14 Number of delivery outlets
7 Classification and designation
8 Test report
9 Information for use
  9.1 General
  9.2 Signs and warning signs
  9.3 Accompanying documents
      9.3.1 General
      9.3.2 Contents
  9.4 Marking
Annex A (informative) Example of the dimension of contour
                      of a transporting device
Annex B (informative) Examples of technical measures for
                      noise reduction
Annex C (informative) Example of an exhaust tail pipe (coupling)
Annex D (informative) Guidance for acceptance tests on delivery
Annex E (normative) Noise test code
  E.1 General
  E.2 Grade of accuracy
  E.3 Installation and mounting conditions
  E.4 Operating conditions
  E.5 Measurement uncertainties
  E.6 Declaration
Annex F (normative) Test of inclination during operation
Annex G (normative) Test of inclination during transport
                      (out of operation)
Annex H (normative) Requirements for non-text safety signs
                      for use on portable pumps
  H.1 General
  H.2 Safety alert symbol
  H.3 Non-text hazard pictorials
  H.4 Dimensions
  H.5 Colours of safety signs
  H.6 Location
Annex ZA (informative) Relationship between this European
                       Standard and the Essential Requirements
                       of EU Directive 98/37/EC
Annex ZB (informative) Relationship between this European
                       Standard and the Essential Requirements
                       of EU Directive 2006/42/EC
Bibliography

This document applies to portable pumps using fire-fighting centrifugal pumps as defined in EN 1028, drivenby an internal combustion engine and not intended to be permanently installed in fire-fighting and rescueservice vehicles and not intended for prolonged unattended operation.NOTE 1 If use of the portable pump is foreseen for prolonged unattended operation, this should be agreed between thepurchaser and the manufacturer or the manufacturer‘s authorized representative at the time of ordering. In this case anadditional risk analysis should be carried out.This document deals with all significant hazards, hazardous situations and events relevant to portable firefightingpumps as described above, when they are used as intended and under the conditions foreseen by themanufacturer (see Clause 4). It addresses the design, setting up, and operation of the portable pump.This document also specifies performance requirements for portable pumps in its scope.This document applies to portable pumps used in ambient temperatures between –15 °C and + 35 °C.NOTE 2 Additional measures may be necessary for ambient temperatures beyond the limits –15 °C and + 35 °CThis document does not cover the effect on performance of water inlet temperatures above + 20°C.This document does not contain any requirements for inlet and outlet connection couplings.NOTE 3 For inlet and outlet connection couplings national regulations apply. The design should be agreed at the timeof ordering between purchaser and the manufacturer or manufacturer‘s authorized representative.This document does not contain specific requirements for the driving engine but deals with the hazards relatedto the interface between engine and pump.