EN 14409-3:2004
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Plastics piping systems for renovation of underground water supply networks - Part 3: Lining with close fit-pipes
04-01-2011
09-29-2004
Foreword
1 Scope
2 Normative references
3 Terms, definitions, symbols and abbreviations
4 Pipes at the "M" stage
5 Fittings at the "M" stage
6 Valves
7 Fitness for purpose of the lining system at the "I" stage
8 Installation practice
Annex A (informative) Guidance for assessment of conformity
Annex B (normative) Factory folded heat reverted polyethylene
(PE) pipe - Determination of memory ability
Annex C (informative) Folded polyethylene (PE) pipe -
Determination of resistance to circumferential
tensile stress at constant temperature
Bibliography
This part 3 of EN 14409, in conjunction with EN 14409-1 specifies requirements and test methods for close-fit lining systems intended to be used for the renovation of water supply networks of water intended for human consumption, including raw water intake pipelinesIt covers polyethylene (PE) pipe for both independent and interactive pressure pipe liners and associated fittings and joints for the construction of the lining system.
| Committee |
CEN/TC 155
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| NEN EN 14409-3 : 2004 | Identical |
| SN EN 14409-3 : 2005 | Identical |
| I.S. EN 14409-3:2004 | Identical |
| UNE-EN 14409-3:2005 | Identical |
| PN EN 14409-3 : 2006 | Identical |
| NBN EN 14409-3 : 2004 | Identical |
| UNI EN 14409-3 : 2005 | Identical |
| NS EN 14409-3 : 1ED 2004 | Identical |
| NF EN 14409-3 : 2005 | Identical |
| BS EN 14409-3:2004 | Identical |
| DIN EN 14409-3:2004-12 | Identical |
| DIN EN 14409-1:2004-12 | PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND WATER SUPPLY NETWORKS - PART 1: GENERAL |
| BS EN 14409-1:2004 | Plastics piping systems for renovation of underground water supply networks General |
| EN 14409-1:2004 | Plastics piping systems for renovation of underground water supply networks - Part 1: General |
| I.S. EN 14409-1:2004 | PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND WATER SUPPLY NETWORKS - PART 1: GENERAL |
| EN 12201-4:2012 | Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 4: Valves |
| EN 12201-3:2011+A1:2012 | Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 3: Fittings |
| ISO 12176-1:2017 | Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 1: Butt fusion |
| ISO 3:1973 | Preferred numbers Series of preferred numbers |
| EN 14409-1:2004 | Plastics piping systems for renovation of underground water supply networks - Part 1: General |
| ISO 12176-2:2008 | Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 2: Electrofusion |
| ISO/TR 11295:1992 | Techniques for rehabilitation of pipeline sytems by the use of plastics pipes and fittings |
| ISO 3126:2005 | Plastics piping systems Plastics components Determination of dimensions |
| EN 921:1994/AC:1995 | PLASTICS PIPING SYSTEMS - THERMOPLASTICS PIPES - DETERMINATION OF RESISTANCE TO INTERNAL PRESSURE AT CONSTANT TEMPERATURE |
| EN 12201-5:2011 | Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 5: Fitness for purpose of the system |
| EN 13689 : 2002 | GUIDANCE ON THE CLASSIFICATION AND DESIGN OF PLASTICS PIPING SYSTEMS USED FOR RENOVATION |
| EN 12201-2:2011+A1:2013 | Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 2: Pipes |
| PREN ISO 3126 : DRAFT 1999 | PLASTICS PIPING SYSTEMS - PLASTICS PIPING COMPONENTS - MEASUREMENT AND DETERMINATION OF DIMENSIONS |
| ISO 497:1973 | Guide to the choice of series of preferred numbers and of series containing more rounded values of preferred numbers |
| ISO 899-1:2017 | Plastics — Determination of creep behaviour — Part 1: Tensile creep |
| EN 12201-1:2011 | Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 1: General |
| CEN/TS 12201-7:2014 | Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 7: Guidance for the assessment of conformity |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.