EN 14408-1:2004
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Plastics piping systems for renovation of underground gas supply networks - Part 1: General
02-01-2013
09-29-2004
Foreword
Introduction
1 Scope
2 Normative references
3 Terms, definitions, symbols and abbreviations
4 Pipes at the "M" stage
5 Fittings at the "M" stage
6 Valves
7 Fitness for purpose of the Lining at the "I" stage
8 Installation practice
Annex A (informative) Recommended scheme for assessment
of conformity
Bibliography
This document specifies the requirements and test methods for plastics piping systems used for renovation of underground gas supply networks. It is applicable to pipes and fittings as manufactured as well as to the installed lining system; it does not cover sprayed coatings, the existing pipeline or any annular filler.Functional recommendations on this subject are covered by EN 12007 parts 1 and 4.This part of EN 14408 deals with the general requirements common to all relevant renovation techniques as defined in 3.2.
| Committee |
CEN/TC 155
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| NBN EN 14408-1 : 2004 | Identical |
| DIN EN 14408-1:2004-12 | Identical |
| NEN EN 14408-1 : 2004 | Identical |
| I.S. EN 14408-1:2004 | Identical |
| UNI EN 14408-1 : 2005 | Identical |
| NF EN 14408-1 : 2005 | Identical |
| NS EN 14408-1 : 1ED 2004 | Identical |
| SN EN 14408-1 : 2005 | Identical |
| PN EN 14408-1 : 2006 | Identical |
| BS EN 14408-1:2004 | Identical |
| UNE-EN 14408-1:2005 | Identical |
| I.S. EN 14408-3:2004 | PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND GAS SUPPLY NETWORKS - PART 3: LINING WITH CLOSE-FIT PIPES |
| BS EN 14408-3:2004 | Plastics piping systems for renovation of underground gas supply networks Lining with close-fit pipes |
| EN 14408-3:2004 | Plastics piping systems for renovation of underground gas supply networks - Part 3: Lining with close-fit pipes |
| DIN EN 14408-3:2004-12 | PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND GAS SUPPLY NETWORKS - PART 3: LINING WITH CLOSE-FIT PIPES |
| EN 12327:2012 | Gas infrastructure - Pressure testing, commissioning and decommissioning procedures - Functional requirements |
| ISO/IEC Guide 62:1996 | General requirements for bodies operating assessment and certification/registration of quality systems |
| EN 12007-1:2012 | Gas infrastructure - Pipelines for maximum operating pressure up to and including 16 bar - Part 1: General functional requirements |
| EN 45011:1998 | General requirements for bodies operating product certification systems (ISO/IEC Guide 65:1996) |
| EN 14408-3:2004 | Plastics piping systems for renovation of underground gas supply networks - Part 3: Lining with close-fit pipes |
| EN 45011 : 1998 | GENERAL REQUIREMENTS FOR BODIES OPERATING PRODUCT CERTIFICATION SYSTEMS |
| ISO/TR 11295:1992 | Techniques for rehabilitation of pipeline sytems by the use of plastics pipes and fittings |
| ISO 472:2013 | Plastics — Vocabulary |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| EN 13689 : 2002 | GUIDANCE ON THE CLASSIFICATION AND DESIGN OF PLASTICS PIPING SYSTEMS USED FOR RENOVATION |
| ISO 9001:2015 | Quality management systems — Requirements |
| EN 12007-2:2012 | Gas infrastructure - Pipelines for maximum operating pressure up to and including 16 bar - Part 2: Specific functional requirements for polyethylene (MOP up to and including 10 bar) |
| ISO/IEC Guide 65:1996 | General requirements for bodies operating product certification systems |
| EN 12007-4:2012 | Gas infrastructure - Pipelines for maximum operating pressure up to and including 16 bar - Part 4: Specific functional requirements for renovation |
| EN 45012 : 1998 | GENERAL REQUIREMENTS FOR BODIES OPERATING ASSESSMENT AND CERTIFICATION/REGISTRATION OF QUALITY SYSTEMS |
| ISO 1043-1:2011 | Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics |
| EN ISO 472:2013 | Plastics - Vocabulary (ISO 472:2013) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.