EN 14305:2015
Current
The latest, up-to-date edition.
Thermal insulation products for building equipment and industrial installations - Factory made cellular glass (CG) products - Specification
12-09-2015
European foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Requirements
5 Test methods
6 Designation code
7 Assessment and Verification of the Constancy of
Performance (AVCP)
8 Marking and labelling
Annex A (normative) - Factory production control
Annex B (normative) - Determination of minimum service
temperature
Annex C (informative) - Additional properties
Annex D (informative) - Preparation of the flat test
specimens to measure thermal conductivity
Annex ZA (informative) - Clauses of this European
Standard addressing the provisions of the EU
Construction Products Regulation
Bibliography
This European Standard specifies the requirements for factory made cellular glass products which are used for the thermal insulation of building equipment and industrial installations with an operating temperature range of approximately - 265 °C to + 430 °C.Below an operating temperature of - 50 °C, special tests regarding the suitability of the product in the intended application are advised (e.g. liquefaction of oxygen). Manufacturer's advice should be heeded in all cases.The products are manufactured in the form of faced or unfaced boards, pipe sections, segments and prefabricated ware.This European Standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling.Products covered by this standard are also used in prefabricated thermal insulation systems and composite panels; the performance of systems incorporating these products is not covered.This European Standard does not specify the required level of a given property that should be achieved by a product to demonstrate fitness for purpose in a particular application. The levels required for a given application can be found in regulations and invitations to tender.Products with a declared thermal conductivity greater than 0,065 W/(m·K) at 10 °C are not covered by this standard.This European Standard does not cover products for the insulation of the building structure.
Committee |
CEN/TC 88
|
DevelopmentNote |
Supersedes PREN 14305. (01/2016)
|
DocumentType |
Standard
|
PublisherName |
Comite Europeen de Normalisation
|
Status |
Current
|
Supersedes |
Standards | Relationship |
DIN EN 14305:2016-03 | Identical |
SS-EN 14305:2015 | Identical |
I.S. EN 14305:2015 | Identical |
PN EN 14305 : 2016 | Identical |
NBN EN 14305 : 2016 | Identical |
UNE-EN 14305:2017 | Identical |
UNI EN 14305 : 2013 | Identical |
NEN EN 14305 : 2015 | Identical |
SN EN 14305 : 2015 | Identical |
BS EN 14305:2015 | Identical |
UNI EN 14305:2016 | Identical |
NF EN 14305 : 2016 | Identical |
NS EN 14305 : 2015 | Identical |
07/30167661 DC : DRAFT AUG 2007 | BS EN 15715 - THERMAL INSULATION PRODUCTS - INSTRUCTIONS FOR MOUNTING AND FIXING FOR REACTION TO FIRE TESTING - FACTORY MADE PRODUCTS |
UNE-EN 16783:2017 | Thermal insulation products - Product category rules (PCR) for factory made and in-situ formed products for preparing environmental product declarations |
EN 13172:2012 | Thermal insulation products - Evaluation of conformity |
UNI EN 15715 : 2009 | THERMAL INSULATION PRODUCTS - INSTRUCTIONS FOR MOUNTING AND FIXING FOR REACTION TO FIRE TESTING - FACTORY MADE PRODUCTS |
I.S. EN 13167:2012 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE CELLULAR GLASS (CG) PRODUCTS - SPECIFICATION |
I.S. EN 13172:2012 | THERMAL INSULATION PRODUCTS - EVALUATION OF CONFORMITY |
VDI 2055 Blatt 2:2013-10 | Thermal insulation of heated and refrigerated operational installations in the industry and in the building services - Technical basics for the verification of properties of insulating materials |
14/30301580 DC : 0 | BS EN/TC 16783 - THERMAL INSULATION PRODUCTS - PRODUCT CATEGORY RULES (PCR) FOR FACTORY MADE AND IN-SITU FORMED PRODUCTS FOR PREPARING ENVIRONMENTAL PRODUCT DECLARATIONS |
PREN 13167 : DRAFT 2010 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE CELLULAR GLASS (CG) PRODUCTS - SPECIFICATION |
DIN EN 15715:2010-04 | Thermal insulation products - Instructions for mounting and fixing for reaction to fire testing - Factory made products |
10/30213974 DC : 0 | BS EN 13167 - THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE CELLULAR GLASS (CG) PRODUCTS - SPECIFICATION |
I.S. EN 16783:2017 | THERMAL INSULATION PRODUCTS - PRODUCT CATEGORY RULES (PCR) FOR FACTORY MADE AND IN-SITU FORMED PRODUCTS FOR PREPARING ENVIRONMENTAL PRODUCT DECLARATIONS |
I.S. EN 15715:2009 | THERMAL INSULATION PRODUCTS - INSTRUCTIONS FOR MOUNTING AND FIXING FOR REACTION TO FIRE TESTING - FACTORY MADE PRODUCTS |
DIN EN 13172:2012-04 | THERMAL INSULATION PRODUCTS - EVALUATION OF CONFORMITY |
DIN EN 13167:2015-04 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE CELLULAR GLASS (CG) PRODUCTS - SPECIFICATION |
BS EN 13172:2012 | Thermal insulation products. Evaluation of conformity |
UNI EN 13172 : 2012 | Thermal insulation products - Evaluation of conformity |
UNE-EN 15715:2012 | Thermal insulation products - Instructions for mounting and fixing for reaction to fire testing - Factory made products |
BS EN 13167 : 2012 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE CELLULAR GLASS (CG) PRODUCTS - SPECIFICATION |
UNE-EN 13167:2013 | Thermal insulation products for buildings - Factory made cellular glass (CG) products - Specification |
UNE-EN 13172:2012 | Thermal insulation products - Evaluation of conformity |
EN 16783:2017 | Thermal insulation products - Product category rules (PCR) for factory made and in-situ formed products for preparing environmental product declarations |
EN 15715:2009 | Thermal insulation products - Instructions for mounting and fixing for reaction to fire testing - Factory made products |
BS EN 16783:2017 | Thermal insulation products. Product category rules (PCR) for factory made and in-situ formed products for preparing environmental product declarations |
BS EN 15715:2009 | Thermal insulation products. Instructions for mounting and fixing for reaction to fire testing. Factory made products |
EN 13167:2012+A1:2015 | Thermal insulation products for buildings - Factory made cellular glass (CG) products - Specification |
ISO 9229:2007 | Thermal insulation Vocabulary |
EN 12667:2001 | Thermal performance of building materials and products - Determination of thermal resistance by means of guarded hot plate and heat flow meter methods - Products of high and medium thermal resistance |
ISO 13787:2003 | Thermal insulation products for building equipment and industrial installations Determination of declared thermal conductivity |
EN 14706:2012 | Thermal insulating products for building equipment and industrial installations - Determination of maximum service temperature |
EN 12085:2013 | Thermal insulating products for building applications - Determination of linear dimensions of test specimens |
EN 13468:2001 | Thermal insulating products for building equipment and industrial installations - Determination of trace quantities of water soluble chloride, fluoride, silicate, sodium ions and pH |
EN 1607:2013 | Thermal insulating products for building applications - Determination of tensile strength perpendicular to faces |
ISO 354:2003 | Acoustics — Measurement of sound absorption in a reverberation room |
EN 13820:2003 | Thermal insulating materials for building applications - Determination of organic content |
EN 1606:2013 | Thermal insulating products for building applications - Determination of compressive creep |
EN 1608:2013 | Thermal insulating products for building applications - Determination of tensile strength parallel to faces |
EN 13471:2001 | Thermal insulating products for building equipment and industrial installations - Determination of the coefficient of thermal expansion |
EN 12939:2000 | Thermal performance of building materials and products - Determination of thermal resistance by means of guarded hot plate and heat flow meter methods - Thick products of high and medium thermal resistance |
EN ISO 8497:1996 | Thermal insulation - Determination of steady-state thermal transmission properties of thermal insulation for circular pipes (ISO 8497:1994) |
ISO 1716:2010 | Reaction to fire tests for products Determination of the gross heat of combustion (calorific value) |
ISO 7884-7:1987 | Glass — Viscosity and viscometric fixed points — Part 7: Determination of annealing point and strain point by beam bending |
EN ISO 9229:2007 | Thermal insulation - Vocabulary (ISO 9229:2007) |
EN 824:2013 | Thermal insulating products for building applications - Determination of squareness |
ISO 11925-2:2010 | Reaction to fire tests Ignitability of products subjected to direct impingement of flame Part 2: Single-flame source test |
EN ISO 1182:2010 | Reaction to fire tests for products - Non-combustibility test (ISO 1182:2010) |
EN 825:2013 | Thermal insulating products for building applications - Determination of flatness |
EN 823:2013 | Thermal insulating products for building applications - Determination of thickness |
ISO 8497:1994 | Thermal insulation — Determination of steady-state thermal transmission properties of thermal insulation for circular pipes |
EN ISO 13787:2003 | Thermal insulation products for building equipment and industrial installations - Determination of declared thermal conductivity (ISO 13787:2003) |
EN 13470:2001 | Thermal insulating products for building equipment and industrial installations - Determination of the apparent density of preformed pipe insulation |
EN 13238:2010 | Reaction to fire tests for building products - Conditioning procedures and general rules for selection of substrates |
ISO 1182:2010 | Reaction to fire tests for products Non-combustibility test |
EN 13823:2010+A1:2014 | Reaction to fire tests for building products - Building products excluding floorings exposed to the thermal attack by a single burning item |
EN 1602:2013 | Thermal insulating products for building applications - Determination of the apparent density |
EN 12087:2013 | Thermal insulating products for building applications - Determination of long term water absorption by immersion |
ISO 11654:1997 | Acoustics — Sound absorbers for use in buildings — Rating of sound absorption |
EN 12090:2013 | Thermal insulating products for building applications - Determination of shear behaviour |
EN 13472:2012 | Thermal insulating products for building equipment and industrial installations - Determination of short term water absorption by partial immersion of preformed pipe insulation |
EN 1603:2013 | Thermal insulating products for building applications - Determination of dimensional stability under constant normal laboratory conditions (23 °C/ 50 % relative humidity) |
EN 1604:2013 | Thermal insulating products for building applications - Determination of dimensional stability under specified temperature and humidity conditions |
EN ISO 354:2003 | Acoustics - Measurement of sound absorption in a reverberation room (ISO 354:2003) |
EN 14707:2012 | Thermal insulating products for building equipment and industrial installations - Determination of maximum service temperature for preformed pipe insulation |
EN 12089:2013 | Thermal insulating products for building applications - Determination of bending behaviour |
ISO 10456:2007 | Building materials and products — Hygrothermal properties — Tabulated design values and procedures for determining declared and design thermal values |
ISO 65:1981 | Carbon steel tubes suitable for screwing in accordance with ISO 7-1 |
EN 13167:2012+A1:2015 | Thermal insulation products for buildings - Factory made cellular glass (CG) products - Specification |
EN 12430:2013 | Thermal insulating products for building applications - Determination of behaviour under point load |
EN 1609:2013 | Thermal insulating products for building applications - Determination of short term water absorption by partial immersion |
EN 826:2013 | Thermal insulating products for building applications - Determination of compression behaviour |
EN ISO 1716:2010 | Reaction to fire tests for products - Determination of the gross heat of combustion (calorific value) (ISO 1716:2010) |
EN ISO 11654:1997 | Acoustics - Sound absorbers for use in buildings - Rating of sound absorption (ISO 11654:1997) |
EN 15715:2009 | Thermal insulation products - Instructions for mounting and fixing for reaction to fire testing - Factory made products |
EN 12086:2013 | Thermal insulating products for building applications - Determination of water vapour transmission properties |
EN 13172:2012 | Thermal insulation products - Evaluation of conformity |
EN 822:2013 | Thermal insulating products for building applications - Determination of length and width |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.