EN 13823:2010+A1:2014
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Reaction to fire tests for building products - Building products excluding floorings exposed to the thermal attack by a single burning item
Superseded date
05-28-2020
Superseded by
Published date
11-12-2014
Publisher
Sorry this product is not available in your region.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Test facility
5 Test specimen
6 Conditioning
7 Principle
8 Test procedure
9 Expression of results
10 Test report
Annex A (normative) - Calculation procedures
Annex B (informative) - Precision of test method
Annex C (normative) - Calibration procedures
Annex D (informative) - Calibration procedures
Annex E (normative) - Design drawings
Annex F (informative) - Data file format
Annex G (informative) - Record sheet
Bibliography
This European Standard specifies a method of test for determining the reaction to fire performance of construction products excluding floorings, and excluding products which are indicated in Table 1 of EC Decision 2000/147/EC, when exposed to thermal attack by a single burning item (SBI). The calculation procedures are given in Annex A. Information on the precision of the test method is given in Annex B. The calibration procedures are given in Annexes C and D, of which C is a normative annex.NOTEThis European Standard has been developed to determine the reaction to fire performance of essentially flat products. The treatment of some families of products, e.g. linear products (pipes, ducts, cables etc.), can need special rules.
| Committee |
CEN/TC 127
|
| DevelopmentNote |
2010 Edition Re-Issued in November 2014 & incorporates AMD 1 2014. (11/2014)
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| SN EN 13823 : 2010 + A1 2014 | Identical |
| UNI EN 13823 : 2014 | Identical |
| DIN EN 13823:2015-02 | Identical |
| NBN EN 13823 : 2010 + A1 2014 | Identical |
| PN EN 13823 : 2010 + A1 2014 | Identical |
| NS EN 13823 : 2010 + A1 2014 | Identical |
| I.S. EN 13823:2010 | Identical |
| NF EN 13823 : 2013 + A1 2015 | Identical |
| NEN EN 13823 : 2010 + A1 2014 | Identical |
| BS EN 13823 : 2010 | Identical |
| ONORM EN 13823 : 2015 | Identical |
| UNE-EN 13823:2012+A1:2016 | Identical |
| DIN EN 13823:2019-02 (Draft) | Identical |
| UNE-EN 13823:2012 | Identical |
| BS EN 13823:2010+A1:2014 | Identical |
| 12/30265298 DC : 0 | BS EN 12050-4 - WASTEWATER LIFTING PLANTS FOR BUILDINGS AND SITES - PART 4: NON-RETURN VALVES FOR FAECAL-FREE WASTEWATER AND WASTEWATER CONTAINING FAECAL MATTER |
| PREN 15497 : DRAFT 2011 | STRUCTURAL FINGER JOINTED SOLID TIMBER - PERFORMANCE REQUIREMENTS AND MINIMUM PRODUCTION REQUIREMENTS |
| 12/30265310 DC : 0 | BS EN 124-5 - GULLY TOPS AND MANHOLE TOPS FOR VEHICULAR AND PEDESTRIAN AREAS - PART 5: GULLY TOPS AND MANHOLE TOPS MADE FROM COMPOSITE MATERIALS |
| BS EN 15564:2008 | Precast concrete products. Resin bound concrete. Requirements and test methods |
| EN 438-9:2017 | High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (usually called laminates) - Part 9: Classification and specifications for alternative core laminates |
| PD CEN/TS 15912:2012 | Durability of reaction to fire performance. Classes of fire-retardant treated wood-based product in interior and exterior end use applications |
| 10/30233946 DC : 0 | BS EN 544 - BITUMEN SHINGLES WITH MINERAL AND/OR SYNTHETIC REINFORCEMENTS - PRODUCT SPECIFICATION AND TEST METHODS |
| BS EN 15651-2:2017 | Sealants for non-structural use in joints in buildings and pedestrian walkways Sealants for glazing |
| 07/30172710 DC : 0 | BS EN 438-8 - HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 8: CLASSIFICATION AND SPECIFICATIONS FOR DESIGN LAMINATES |
| 17/30357440 DC : DRAFT SEP 2017 | BS EN 438-8 - HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 8: CLASSIFICATION AND SPECIFICATIONS FOR DESIGN LAMINATES |
| DIN EN 14320-1:2013-04 | THERMAL INSULATING PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - IN-SITU FORMED SPRAYED RIGID POLYURETHANE (PUR) AND POLYISOCYANURATE (PIR) FOAM PRODUCTS - PART 1: SPECIFICATION FOR THE RIGID FOAM SPRAY SYSTEM BEFORE INSTALLATION |
| 10/30233182 DC : 0 | BS EN 492 - FIBRE-CEMENT SLATES AND FITTINGS - PRODUCT SPECIFICATION AND TEST METHODS |
| 11/30237554 DC : 0 | BS EN 14732 - TIMBER STRUCTURES - PREFABRICATED WALL, FLOOR AND ROOF ELEMENTS - REQUIREMENTS |
| 07/30166838 DC : 0 | BS EN 13238 - REACTION TO FIRE TESTS FOR BUILDING - CONDITIONING PROCEDURES AND GENERAL RULES FOR SELECTION OF SUBSTRATES |
| CEN/TR 14819-2:2005 | Safety recommendations for cableway installations designed to carry persons - Prevention and fight against fire - Part 2: Other funicular railways and other installations |
| 12/30265289 DC : 0 | BS EN 12050-1 - WASTEWATER LIFTING PLANTS FOR BUILDINGS AND SITES - PART 1: LIFTING PLANTS FOR WASTEWATER CONTAINING FAECAL MATTER |
| 13/30268273 DC : 0 | BS EN 14915 - SOLID WOOD PANELLING AND CLADDING - CHARACTERISTICS, EVALUATION OF CONFORMITY AND MARKING |
| 12/30254917 DC : DRAFT JAN 2012 | BS EN 877 - CAST IRON PIPES AND FITTINGS, THEIR JOINTS AND ACCESSORIES FOR THE EVACUATION OF WATER FROM BUILDINGS - REQUIREMENTS, TEST METHODS AND QUALITY ASSURANCE |
| 11/30238641 DC : 0 | BS EN 491 - CONCRETE ROOFING TILES AND FITTINGS FOR ROOF COVERING AND WALL CLADDING - TEST METHODS |
| I.S. EN 12101-2:2017 | SMOKE AND HEAT CONTROL SYSTEMS - PART 2: NATURAL SMOKE AND HEAT EXHAUST VENTILATORS |
| PREN 14313 : DRAFT 2015 | THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - FACTORY MADE POLYETHYLENE FOAM (PEF) PRODUCTS - SPECIFICATION |
| 11/30251988 DC : 0 | BS EN 14190 - GYPSUM PLASTERBOARD PRODUCTS FROM PROCESSING - DEFINITIONS, REQUIREMENTS AND TEST METHODS |
| DIN EN 15619 E : 2014 | RUBBER OR PLASTIC COATED FABRICS - SAFETY OF TEMPORARY STRUCTURES (TENTS) - SPECIFICATION FOR COATED FABRICS INTENDED FOR TENTS AND RELATED STRUCTURES |
| PREN 598 : DRAFT 2017 | COATED AND LINED DUCTILE IRON PIPES, FITTINGS AND THEIR JOINTS FOR SEWERAGE AND DRAINAGE APPLICATIONS - PRODUCTS CHARACTERISTICS AND TEST AND ASSESSMENT METHODS |
| PREN 13859-2 : DRAFT 2013 | FLEXIBLE SHEETS FOR WATERPROOFING - DEFINITIONS AND CHARACTERISTICS OF UNDERLAYS - PART 2: UNDERLAYS FOR WALLS |
| 10/30233189 DC : 0 | BS EN 494 - FIBRE-CEMENT PROFILED SHEETS AND FITTINGS - PRODUCT SPECIFICATION AND TEST METHODS |
| PREN 1504-2 : DRAFT 2015 | PRODUCTS AND SYSTEMS FOR THE PROTECTION AND REPAIR OF CONCRETE STRUCTURES - DEFINITIONS, REQUIREMENTS, QUALITY CONTROL AND EVALUATION OF CONFORMITY - PART 2: SURFACE PROTECTION SYSTEMS FOR CONCRETE |
| UNE-EN 14306:2017 | Thermal insulation products for building equipment and industrial installations - Factory made calcium silicate (CS) products - Specification |
| DIN EN 124-6:2015-09 | GULLY TOPS AND MANHOLE TOPS FOR VEHICULAR AND PEDESTRIAN AREAS - PART 6: GULLY TOPS AND MANHOLE TOPS MADE OF POLYPROPYLENE (PP), POLYETHYLENE (PE) OR UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) |
| DIN EN 13245-2:2010-11 | Plastics - Unplasticized poly(vinyl chloride) (PVC-U) profiles for building applications - Part 2: PVC-U profiles and PVC-UE profiles for internal and external wall and ceiling finishes (includes Corrigendum AC:2009) |
| 11/30239903 DC : DRAFT MAR 2011 | BS EN 15013 - PLASTICS PIPING SYSTEMS - NON-PRESSURE DRAINAGE AND SEWERAGE PIPING COMPONENTS BURIED IN GROUND - REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR PIPES AND FITTINGS |
| 11/30239906 DC : 0 | BS EN 15014 - PLASTICS PIPING SYSTEMS - BURIED AND ABOVE GROUND PIPING COMPONENTS FOR WATER AND OTHER LIQUIDS UNDER PRESSURE - REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR PIPES AND FITTINGS |
| 13/30217369 DC : 0 | BS EN 13964 - SUSPENDED CEILINGS - REQUIREMENTS AND TEST METHODS |
| 02/105004 DC : DRAFT JULY 2002 | PREN 14509 - SELF-SUPPORTING DOUBLE SKIN METAL FACED INSULATING SANDWICH PANELS - FACTORY MADE PRODUCTS - SPECIFICATION |
| 13/30288842 DC : 0 | BS EN 14081-1 - TIMBER STRUCTURES - STRENGTH GRADED STRUCTURAL TIMBER WITH RECTANGULAR CROSS SECTION - PART 1: GENERAL REQUIREMENTS |
| 11/30251994 DC : 0 | BS EN 13963 - JOINTING MATERIALS FOR GYPSUM BOARDS - DEFINITIONS, REQUIREMENTS AND TEST METHODS |
| 10/30213965 DC : 0 | BS EN 13164 - THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE EXTRUDED POLYSTYRENE FOAM (XPS) PRODUCTS - SPECIFICATION |
| 10/30212171 DC : 0 | BS EN 15037-5 - PRECAST CONCRETE PRODUCTS - BEAM-AND-BLOCK FLOOR SYSTEMS - PART 5: LIGHTWEIGHT BLOCKS FOR SIMPLE FORMWORK |
| 06/30155785 DC : 0 | BS EN 15564 - PRECAST CONCRETE PRODUCTS - RESIN BOUND CONCRETE - REQUIREMENTS AND TEST METHODS |
| PREN 13963 : DRAFT 2011 | JOINTING MATERIALS FOR GYPSUM BOARDS - DEFINITIONS, REQUIREMENTS AND TEST METHODS |
| 07/30167661 DC : DRAFT AUG 2007 | BS EN 15715 - THERMAL INSULATION PRODUCTS - INSTRUCTIONS FOR MOUNTING AND FIXING FOR REACTION TO FIRE TESTING - FACTORY MADE PRODUCTS |
| 09/30203195 DC : 0 | BS EN 15497 - FINGER JOINTED STRUCTURAL TIMBER - PERFORMANCE REQUIREMENTS AND MINIMUM PRODUCTION REQUIREMENTS |
| 12/30256977 DC : 0 | BS EN 15619 - RUBBER OR PLASTIC COATED FABRICS - SAFETY OF TEMPORARY STRUCTURES (TENTS) - SPECIFICATION FOR COATED FABRICS INTENDED FOR TENTS AND RELATED STRUCTURES |
| 08/30169531 DC : DRAFT APR 2008 | BS EN 13162 - THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE MINERAL WOOL (MW) PRODUCTS - SPECIFICATION |
| 05/30136503 DC : 0 | PREN 14309 - THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - FACTORY MADE PRODUCTS OF EXPANDED POLYSTYRENE (EPS) - SPECIFICATION |
| 05/30134359 DC : DRAFT MAY 2005 | EN 15101-1 - THERMAL INSULATION PRODUCTS FOR BUILDINGS - IN-SITU FORMED LOOSE-FILL CELLULOSE PRODUCTS - PART 1: SPECIFICATION FOR THE PRODUCTS BEFORE INSTALLATION |
| PREN 14309 : DRAFT 2015 | THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - FACTORY MADE PRODUCTS OF EXPANDED POLYSTYRENE (EPS) - SPECIFICATION |
| PREN 438-3 : DRAFT 2014 | HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 3: CLASSIFICATION AND SPECIFICATIONS FOR LAMINATES LESS THAN 2 MM THICK INTENDED FOR BONDING TO SUPPORTING SUBSTRATES |
| PREN 12050-2 : DRAFT 2012 | WASTEWATER LIFTING PLANTS FOR BUILDINGS AND SITES - PRINCIPLES OF CONSTRUCTION AND TESTING - PART 2: LIFTING PLANTS FOR FAECAL-FREE WASTEWATER |
| I.S. EN 15501:2015 | THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - FACTORY MADE EXPANDED PERLITE (EP) AND EXFOLIATED VERMICULITE (EV) PRODUCTS - SPECIFICATION |
| PD CEN/TS 115-4:2015 | Safety of escalators and moving walks Interpretations related to EN 115 family of standards |
| DIN EN 14306:2016-03 | THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - FACTORY MADE CALCIUM SILICATE (CS) PRODUCTS - SPECIFICATION |
| UNE-EN 16623:2015 | Paints and varnishes - Reactive coatings for fire protection of metallic substrates - Definitions, requirements, characteristics and marking |
| I.S. EN 438-9:2017 | HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 9: CLASSIFICATION AND SPECIFICATIONS FOR ALTERNATIVE CORE LAMINATES |
| 04/101694 DC : DRAFT JAN 2004 | EN 544 - BITUMEN SHINGLES WITH MINERAL AND/OR SYNTHETIC REINFORCEMENTS - PRODUCT SPECIFICATION AND TEST METHODS |
| UNI EN 16240 : 2014 | LIGHT TRANSMITTING FLAT SOLID POLYCARBONATE (PC) SHEETS FOR INTERNAL AND EXTERNAL USE IN ROOFS, WALLS AND CEILINGS - REQUIREMENTS AND TEST METHODS |
| 05/30136556 DC : 0 | PREN 14313 - THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATION - FACTORY MADE POLYETHYLENE FOAM (PEF) PRODUCTS - SPECIFICATION |
| PREN 14081-1 : DRAFT 2013 | TIMBER STRUCTURES - STRENGTH GRADED STRUCTURAL TIMBER WITH RECTANGULAR CROSS SECTION - PART 1: GENERAL REQUIREMENTS |
| UNE-EN 15286:2013 | Agglomerated stone - Slabs and tiles for wall finishes (internal and external) |
| BS EN 15651-3:2017 | Sealants for non-structural use in joints in buildings and pedestrian walkways Sealants for sanitary joints |
| DIN EN 16069:2015-04 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE PRODUCTS OF POLYETHYLENE FOAM (PEF) - SPECIFICATION |
| S.R. CEN/TS 15912:2012 | DURABILITY OF REACTION TO FIRE PERFORMANCE - CLASSES OF FIRE-RETARDANT TREATED WOOD-BASED PRODUCT IN INTERIOR AND EXTERIOR END USE APPLICATIONS |
| NF EN 14064-1 : 2010 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - IN-SITU FORMED LOOSE-FILL MINERAL WOOL (MW) PRODUCTS - PART 1: SPECIFICATION FOR THE LOOSE-FILL PRODUCTS BEFORE INSTALLATION |
| PREN 13169 : DRAFT 2010 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE EXPANDED PERLITE BOARD (EPB) PRODUCTS - SPECIFICATION |
| CEN/TR 16988:2016 | Estimation of uncertainty in the single burning item test |
| DIN EN 14304:2016-03 | THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - FACTORY MADE FLEXIBLE ELASTOMERIC FOAM (FEF) PRODUCTS - SPECIFICATION |
| CEN/TR 14819-1:2004 | Safety recommendations for cableway installations designed to carry persons - Prevention and fight against fire - Part 1: Funicular railways in tunnels |
| I.S. EN 14320-1:2013 | THERMAL INSULATING PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - IN-SITU FORMED SPRAYED RIGID POLYURETHANE (PUR) AND POLYISOCYANURATE FOAM (PIR) PRODUCTS - PART 1: SPECIFICATION FOR THE RIGID FOAM SPRAY SYSTEM BEFORE INSTALLATION |
| I.S. EN 15101-1:2013 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - IN-SITU FORMED LOOSE FILL CELLULOSE (LFCI) PRODUCTS - PART 1: SPECIFICATION FOR THE PRODUCTS BEFORE INSTALLATION |
| I.S. EN 16000:2010 | PLASTICS PIPING SYSTEMS - SYSTEMS WITHIN THE BUILDING STRUCTURE - MOUNTING AND FIXING OF COMPONENTS IN THE TEST APPARATUS TO THERMAL ATTACK BY A SINGLE BURNING ITEM |
| BS EN 15619:2014 | Rubber or plastic coated fabrics. Safety of temporary structures (tents). Specification for coated fabrics intended for tents and related structures |
| I.S. EN 438-8:2009 | HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 8: CLASSIFICATION AND SPECIFICATIONS FOR DESIGN LAMINATES |
| I.S. EN 13501-1:2007 | FIRE CLASSIFICATION OF CONSTRUCTION PRODUCTS AND BUILDING ELEMENTS - PART 1: CLASSIFICATION USING DATA FROM REACTION TO FIRE TESTS |
| BS EN 16153 : 2013 | LIGHT TRANSMITTING FLAT MULTIWALL POLYCARBONATE (PC) SHEETS FOR INTERNAL AND EXTERNAL USE IN ROOFS, WALLS AND CEILINGS - REQUIREMENTS AND TEST METHODS |
| I.S. EN 12467:2012 | FIBRE-CEMENT FLAT SHEETS - PRODUCT SPECIFICATION AND TEST METHODS |
| I.S. EN 15715:2009 | THERMAL INSULATION PRODUCTS - INSTRUCTIONS FOR MOUNTING AND FIXING FOR REACTION TO FIRE TESTING - FACTORY MADE PRODUCTS |
| I.S. EN 15651-4:2017 | SEALANTS FOR NON-STRUCTURAL USE IN JOINTS IN BUILDINGS AND PEDESTRIAN WALKWAYS - PART 4: SEALANTS FOR PEDESTRIAN WALKWAYS |
| I.S. EN 15701:2016 | PLASTICS - THERMOPLASTIC JACKETS FOR INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - REQUIREMENTS AND TEST METHODS |
| PREN 12050-4 : DRAFT 2012 | WASTEWATER LIFTING PLANTS FOR BUILDINGS AND SITES - PART 4: NON-RETURN VALVES FOR FAECAL-FREE WASTEWATER AND WASTEWATER CONTAINING FAECAL MATTER |
| ISO 2219:2010 | Thermal insulation products for buildings — Factory-made products of expanded cork (ICB) — Specification |
| UNI EN ISO 25762 : 2012 | PLASTICS - GUIDANCE ON THE ASSESSMENT OF THE FIRE CHARACTERISTICS AND FIRE PERFORMANCE OF FIBRE-REINFORCED POLYMER COMPOSITES |
| EN 15102:2007+A1:2011 | Decorative wall coverings - Roll and panel form |
| 12/30268937 DC : 0 | BS EN 16491 - THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE COMPOSITE PRODUCTS - SPECIFICATION |
| 15/30301583 DC : 0 | BS EN 16863 - THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE REFLECTIVE INSULATION PRODUCTS (RI) - SPECIFICATION |
| DIN EN 13501-1:2010-01 | FIRE CLASSIFICATION OF CONSTRUCTION PRODUCTS AND BUILDING ELEMENTS - PART 1: CLASSIFICATION USING DATA FROM REACTION TO FIRE TESTS |
| UNI EN 15101-1 : 2013 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - IN-SITU FORMED LOOSE FILL CELLULOSE (LFCI) PRODUCTS - PART 1: SPECIFICATION FOR THE PRODUCTS BEFORE INSTALLATION |
| UNE-EN 15651-4:2017 | Sealants for non-structural use in joints in buildings and pedestrian walkways - Part 4: Sealants for pedestrian walkways |
| UNE-EN 14318-1:2013 | Thermal insulating products for buildings - In-situ formed dispensed rigid polyurethane (PUR) and polyisocyanurate (PIR) foam products - Part 1: Specification for the rigid foam dispensed system before installation |
| 16/30325907 DC : 0 | BS EN 15102 - DECORATIVE WALLCOVERINGS - ROLL FORM |
| EN 15101-1:2013 | Thermal insulation products for buildings - In-situ formed loose fill cellulose (LFCI) products - Part 1: Specification for the products before installation |
| I.S. EN 15619:2014 | RUBBER OR PLASTIC COATED FABRICS - SAFETY OF TEMPORARY STRUCTURES (TENTS) - SPECIFICATION FOR COATED FABRICS INTENDED FOR TENTS AND RELATED STRUCTURES |
| PREN 16809-1 : DRAFT 2014 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - IN-SITU FORMED PRODUCTS FROM LOOSE-FILL EXPANDED POLYSTYRENE (EPS) BEADS AND BONDED EXPANDED POLYSTYRENE BEADS - PART 1: SPECIFICATION FOR THE BONDED AND LOOSE FILLED PRODUCTS BEFORE INSTALLATION |
| EN 60695-6-1:2005/A1:2010 | FIRE HAZARD TESTING - PART 6-1: SMOKE OBSCURATION - GENERAL GUIDANCE |
| I.S. EN 14915:2013 | SOLID WOOD PANELLING AND CLADDING - CHARACTERISTICS, EVALUATION OF CONFORMITY AND MARKING |
| EN 14915:2013+A1:2017 | Solid wood panelling and cladding - Characteristics, requirements and marking |
| DIN EN 13500:2003-12 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - EXTERNAL THERMAL INSULATION COMPOSITE SYSTEMS (ETICS) BASED ON MINERAL WOOL - SPECIFICATION |
| DIN EN 13169:2015-04 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE EXPANDED PERLITE BOARD (EPB) PRODUCTS - SPECIFICATION |
| DIN EN 13499:2003-12 | Thermal insulation products for buildings - External thermal insulation composite systems (ETICS) based on expanded polystyrene - Specification; German version EN 13499:2003 |
| DIN EN 13859-1:2014-07 | FLEXIBLE SHEETS FOR WATERPROOFING - DEFINITIONS AND CHARACTERISTICS OF UNDERLAYS - PART 1: UNDERLAYS FOR DISCONTINUOUS ROOFING |
| BS EN 14471 : 2013 | CHIMNEYS - SYSTEM CHIMNEYS WITH PLASTIC FLUE LINERS - REQUIREMENTS AND TEST METHODS |
| BS EN 12050-3:2015 | Wastewater lifting plants for buildings and sites Lifting plants for limited applications |
| 13/30280057 DC : 0 | BS EN 13782 - TEMPORARY STRUCTURE - TENTS - SAFETY |
| BS EN 15266:2007 | Stainless steel pliable corrugated tubing kits in buildings for gas with an operating pressure up to 0,5 bar |
| BS EN 491:2011 | Concrete roofing tiles and fittings for roof covering and wall cladding. Test methods |
| 03/318326 DC : DRAFT NOV 2003 | |
| BS EN 13499:2003 | Thermal insulation products for buildings. External thermal insulation composite systems (ETICS) based on expanded polystyrene. Specification |
| BS EN 12101-2:2017 | Smoke and heat control systems Natural smoke and heat exhaust ventilators |
| BS EN 14190:2014 | Gypsum board products from reprocessing. Definitions, requirements and test methods |
| BS EN 438-7:2005 | High-pressure decorative laminates (HPL). Sheets based on thermosetting resins (usually called laminates) Compact laminate and HPL composite panels for internal and external wall and ceiling finishes |
| BS EN 13163 : 2012 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE EXPANDED POLYSTYRENE (EPS) PRODUCTS - SPECIFICATION |
| BS EN 877 : 1999 | CAST IRON PIPES AND FITTINGS, THEIR JOINTS AND ACCESSORIES FOR THE EVACUATION OF WATER FROM BUILDINGS - REQUIREMENTS, TEST METHODS AND QUALITY ASSURANCE |
| UNE-EN 14496:2017 | Gypsum based adhesives for thermal/acoustic insulation composite panels and gypsum boards - Definitions, requirements and test methods |
| BS EN 1873 : 2014 | PREFABRICATED ACCESSORIES FOR ROOFING - INDIVIDUAL ROOFLIGHTS OF PLASTICS - PRODUCT SPECIFICATION AND TEST METHODS |
| UNE-EN 13238:2011 | Reaction to fire tests for building products - Conditioning procedures and general rules for selection of substrates |
| BS EN 14933:2007 | Thermal insulation and light weight fill products for civil engineering applications. Factory made products of expanded polystyrene (EPS). Specification |
| UNE-EN 491:2012 | Concrete roofing tiles and fittings for roof covering and wall cladding - Test methods |
| UNE-EN 60695-8-2:2017 | Fire hazard testing - Part 8-2: Heat release - Summary and relevance of test methods |
| BS EN 12050-2:2015 | Wastewater lifting plants for buildings and sites Lifting plants for faecal-free wastewater |
| BS EN 520 : 2004 | GYPSUM PLASTERBOARDS - DEFINITIONS, REQUIREMENTS AND TEST METHODS |
| BS EN 13168 : 2012 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE WOOD WOOL (WW) PRODUCTS - SPECIFICATION |
| BS EN 13964:2014 | Suspended ceilings. Requirements and test methods |
| BS EN 13164 : 2012 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE EXTRUDED POLYSTYRENE FOAM (XPS) PRODUCTS - SPECIFICATION |
| I.S. EN 13168:2012 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE WOOD WOOL (WW) PRODUCTS - SPECIFICATION |
| EN 16351:2015 | Timber structures - Cross laminated timber - Requirements |
| I.S. EN 13165:2012 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE RIGID POLYURETHANE FOAM (PU) PRODUCTS - SPECIFICATION |
| EN 13500:2003 | Thermal insulation products for buildings - External thermal insulation composite systems (ETICS) based on mineral wool - Specification |
| I.S. EN 877:2000 | CAST IRON PIPES AND FITTINGS, THEIR JOINTS AND ACCESSORIES FOR THE EVACUATION OF WATER FROM BUILDINGS - REQUIREMENTS, TEST METHODS AND QUALITY ASSURANCE |
| DIN EN 14782:2006-03 | Self-supporting metal sheet for roofing, external cladding and internal lining - Product specification and requirements |
| DIN EN 438-8:2009-07 | HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 8: CLASSIFICATION AND SPECIFICATIONS FOR DESIGN LAMINATES |
| DIN EN 14800:2007-06 | Corrugated safety metal hose assemblies for the connection of domestic appliances using gaseous fuels |
| DIN EN 15701:2017-02 | PLASTICS - THERMOPLASTIC JACKETS FOR INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - REQUIREMENTS AND TEST METHODS |
| EN 13499:2003 | Thermal insulation products for buildings - External thermal insulation composite systems (ETICS) based on expanded polystyrene - Specification |
| DIN EN 13830:2015-07 | CURTAIN WALLING - PRODUCT STANDARD |
| DIN EN 14933:2007-12 | Thermal insulation and light weigth fill products for civil engineering applications - Factory made products of expanded polystyrene (EPS) - Specification |
| EN 124-6:2015 | Gully tops and manhole tops for vehicular and pedestrian areas - Part 6: Gully tops and manhole tops made of polypropylene (PP), polyethylene (PE) or unplasticized poly(vinyl chloride) (PVC-U) |
| CEN/TS 15534-1:2007 | Wood-plastics composites (WPC) - Part 1: Test methods for characterisation of WPC materials and products |
| EN 12050-1:2015 | Wastewater lifting plants for buildings and sites - Part 1: Lifting plants for wastewater containing faecal matter |
| DIN EN 14496:2017-09 | GYPSUM BASED ADHESIVES FOR THERMAL/ACOUSTIC INSULATION COMPOSITE PANELS AND GYPSUM BOARDS - DEFINITIONS, REQUIREMENTS AND TEST METHODS |
| EN 13238:2010 | Reaction to fire tests for building products - Conditioning procedures and general rules for selection of substrates |
| EN 12050-3:2015 | Wastewater lifting plants for buildings and sites - Part 3: Lifting plants for limited applications |
| DIN EN 14209:2017-09 | PREFORMED PLASTERBOARD CORNICES - DEFINITIONS, REQUIREMENTS AND TEST METHODS |
| EN 16755:2017 | Durability of reaction to fire performance - Classes of fire-retardant treated wood products in interior and exterior end use applications |
| EN 12004:2007+A1:2012 | Adhesives for tiles - Requirements, evaluation of conformity, classification and designation |
| EN 13166:2012+A2:2016 | Thermal insulation products for buildings - Factory made phenolic foam (PF) products - Specification |
| UNI EN 877 : 2007 | CAST IRON PIPES AND FITTINGS, THEIR JOINTS AND ACCESSORIES FOR THE EVACUATION OF WATER FROM BUILDINGS - REQUIREMENTS, TEST METHODS AND QUALITY ASSURANCE |
| CEN/TS 15679:2007 | Thermal Modified Timber - Definitions and characteristics |
| EN 60695-8-2:2017 | Fire hazard testing - Part 8-2: Heat release - Summary and relevance of test methods |
| EN 1013:2012+A1:2014 | Light transmitting single skin profiled plastics sheets for internal and external roofs, walls and ceilings - Requirements and test methods |
| EN 124-5:2015 | Gully tops and manhole tops for vehicular and pedestrian areas - Part 5: Gully tops and manhole tops made of composite materials |
| DIN EN 13915:2017-09 | PREFABRICATED GYPSUM PLASTERBOARD PANELS WITH A CELLULAR PAPERBOARD CORE - DEFINITIONS, REQUIREMENTS AND TEST METHODS |
| EN 13162:2012+A1:2015 | Thermal insulation products for buildings - Factory made mineral wool (MW) products - Specification |
| EN 13163:2012+A2:2016 | Thermal insulation products for buildings - Factory made expanded polystyrene (EPS) products - Specification |
| EN 12050-2:2015 | Wastewater lifting plants for buildings and sites - Part 2: Lifting plants for faecal-free wastewater |
| EN 14250:2010 | Timber structures - Product requirements for prefabricated structural members assembled with punched metal plate fasteners |
| EN 12101-2:2017 | Smoke and heat control systems - Part 2: Natural smoke and heat exhaust ventilators |
| EN 12050-4:2015 | Wastewater lifting plants for buildings and sites - Part 4: Non-return valves for faecal-free wastewater and wastewater containing faecal matter |
| DIN EN 16000:2010-10 | Plastics piping systems - Systems within the building structure - Mounting and fixing of components in the test apparatus to thermal attack by a single burning item |
| PREN 13830 : DRAFT 2013 | CURTAIN WALLING - PRODUCT STANDARD |
| S.R. CEN/TS 115-4:2015 | SAFETY OF ESCALATORS AND MOVING WALKS - PART 4: INTERPRETATIONS RELATED TO EN 115 FAMILY OF STANDARDS |
| BS EN 438-8:2009 | High-pressure decorative laminates (HPL). Sheets based on thermosetting resins (usually called laminates) Classification and specifications for design laminates |
| 12/30265292 DC : 0 | BS EN 12050-2 - WASTEWATER LIFTING PLANTS FOR BUILDINGS AND SITES - PRINCIPLES OF CONSTRUCTION AND TESTING - PART 2: LIFTING PLANTS FOR FAECAL-FREE WASTEWATER |
| 11/30249114 DC : 0 | BS EN 15497 - STRUCTURAL FINGER JOINTED SOLID TIMBER - PERFORMANCE REQUIREMENTS AND MINIMUM PRODUCTION REQUIREMENTS |
| BS EN ISO 25762:2012 | Plastics. Guidance on the assessment of the fire characteristics and fire performance of fibre-reinforced polymer composites |
| 16/30330679 DC : DRAFT MAR 2016 | BS EN 16977 - THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE CALCIUM SILICATE (CS) PRODUCTS - SPECIFICATION |
| PREN 14915 : DRAFT 2013 | SOLID WOOD PANELLING AND CLADDING - CHARACTERISTICS, EVALUATION OF CONFORMITY AND MARKING |
| 15/30315087 DC : DRAFT MAY 2015 | BS EN 14314 - THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - FACTORY MADE PHENOLIC FOAM (PF) PRODUCTS - SPECIFICATION |
| 15/30315069 DC : DRAFT MAY 2015 | BS EN 14313 - THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - FACTORY MADE POLYETHYLENE FOAM (PEF) PRODUCTS - SPECIFICATION |
| 08/30169546 DC : DRAFT APR 2008 | BS EN 13167 - THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE CELLULAR GLASS (CG) PRODUCTS - SPECIFICATION |
| 13/30266550 DC : 0 | BS EN 14509 - SELF-SUPPORTING DOUBLE SKIN METAL FACED INSULATING PANELS - FACTORY MADE PRODUCTS - SPECIFICATIONS |
| 15/30315075 DC : DRAFT MAY 2015 | BS EN 14305 - THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - FACTORY MADE CELLULAR GLASS (CG) PRODUCTS - SPECIFICATION |
| DIN EN 16623:2015-04 | PAINTS AND VARNISHES - REACTIVE COATINGS FOR FIRE PROTECTION OF METALLIC SUBSTRATES - DEFINITIONS, REQUIREMENTS, CHARACTERISTICS AND MARKING |
| UNI EN 15423 : 2008 | VENTILATION FOR BUILDINGS - FIRE PRECAUTIONS FOR AIR DISTRIBUTION SYSTEMS IN BUILDINGS |
| 16/30332908 DC : 0 | BS EN 14209 - PREFORMED PLASTERBOARD CORNICES - DEFINITIONS, REQUIREMENTS AND TEST METHODS |
| DIN EN ISO 25762:2012-04 | Plastics - Guidance on the assessment of the fire characteristics and fire performance of fibre-reinforced polymer composites (ISO 25762:2009) |
| DIN EN 15283-2:2009-12 | Gypsum boards with fibrous reinforcement - Definitions, requirements and test methods - Part 2: Gypsum fibre boards (includes Amendment A1:2009) |
| 09/30207844 DC : DRAFT OCT 2009 | BS EN 16000 - PLASTICS PIPING SYSTEMS - SYSTEMS WITHIN THE BUILDING STRUCTURE - MOUNTING AND FIXING OF COMPONENTS IN THE TEST APPARATUS TO THERMAL ATTACK BY A SINGLE BURNING ITEM |
| DIN EN 15651-3:2016-10 (Draft) | SEALANTS FOR NON-STRUCTURAL USE IN JOINTS IN BUILDINGS AND PEDESTRIAN WALKWAYS - PART 3: SEALANTS FOR SANITARY JOINTS |
| DIN EN 15228:2009-08 | STRUCTURAL TIMBER - STRUCTURAL TIMBER PRESERVATIVE TREATED AGAINST BIOLOGICAL ATTACK |
| PREN 14064-1 : DRAFT 2016 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - IN-SITU FORMED LOOSE-FILL MINERAL WOOL (MW) PRODUCTS - PART 1: SPECIFICATION FOR THE LOOSE-FILL PRODUCTS BEFORE INSTALLATION |
| 15/30315081 DC : DRAFT MAY 2015 | BS EN 14308 - THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - FACTORY MADE RIGID POLYURETHANE FOAM (PUR) AND POLYISOCYANURATE FOAM (PIR) PRODUCTS - SPECIFICATION |
| 13/30273039 DC : 0 | BS EN 13859-2 - FLEXIBLE SHEETS FOR WATERPROOFING - DEFINITIONS AND CHARACTERISTICS OF UNDERLAYS - PART 2: UNDERLAYS FOR WALLS |
| BS EN 16623:2015 | Paints and varnishes. Reactive coatings for fire protection of metallic substrates. Definitions, requirements, characteristics and marking |
| DIN EN 15651-1:2016-10 (Draft) | SEALANTS FOR NON-STRUCTURAL USE IN JOINTS IN BUILDINGS AND PEDESTRIAN WALKWAYS - PART 1: SEALANTS FOR FACADE ELEMENTS |
| BS EN 14320-1:2013 | Thermal insulating products for building equipment and industrial installations. In-situ formed sprayed rigid polyurethane (PUR) and polyisocyanurate foam (PIR) products Specification for the rigid foam spray system before installation |
| DIN EN 15497:2014-07 | STRUCTURAL FINGER JOINTED SOLID TIMBER - PERFORMANCE REQUIREMENTS AND MINIMUM PRODUCTION REQUIREMENTS |
| 12/30261882 DC : 0 | BS EN 14081-1 - TIMBER STRUCTURES - STRENGTH GRADED STRUCTURAL TIMBER WITH RECTANGULAR CROSS-SECTION - PART 1: GENERAL REQUIREMENTS |
| 10/30213980 DC : 0 | BS EN 13169 - THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE EXPANDED PERLITE BOARD (EPB) PRODUCTS - SPECIFICATION |
| 06/30117323 DC : 0 | ISO 20632 - ROOM TEST FOR PIPE INSULATION |
| DIN EN 16025-1:2013-07 | THERMAL AND/OR SOUND INSULATING PRODUCTS IN BUILDING CONSTRUCTION - BOUND EPS BALLASTINGS - PART 1: REQUIREMENTS FOR FACTORY PREMIXED EPS DRY PLASTER |
| 15/30315078 DC : DRAFT MAY 2015 | BS EN 14307 - THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - FACTORY MADE EXTRUDED POLYSTYRENE FOAM (XPS) PRODUCTS - SPECIFICATION |
| 07/30166064 DC : 0 | BS EN 15701 - PLASTICS - THERMOPLASTIC JACKETS FOR INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - REQUIREMENTS AND TEST METHODS |
| I.S. EN 15283-1:2008 | GYPSUM BOARDS WITH FIBROUS REINFORCEMENT - DEFINITIONS, REQUIREMENTS AND TEST METHODS - PART 1: GYPSUM BOARDS WITH MAT REINFORCEMENT |
| PREN 438-9 : DRAFT 2016 | HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 9: CLASSIFICATION AND SPECIFICATIONS FOR ALTERNATIVE CORE LAMINATES |
| UNI EN 15283-1 : 2009 | GYPSUM BOARDS WITH FIBROUS REINFORCEMENT - DEFINITIONS, REQUIREMENTS AND TEST METHODS - PART 1: GYPSUM BOARDS WITH MAT REINFORCEMENT |
| 05/30136516 DC : 0 | PREN 14308 - THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - FACTORY MADE RIGID POLYURETHANE FOAM (PUR) AND POLYISOCYANURATE FOAM (PIR) PRODUCTS - SPECIFICATION |
| DIN EN 15012:2008-02 | Plastics piping systems - Soil and waste discharge systems within the building structure - Performance characteristics for pipes, fittings and their joints |
| 09/30183765 DC : 0 | BS EN 60695-6-1 A1 ED.2 - FIRE HAZARD TESTING - PART 6-1: SOME OBSCURATION - GENERAL GUIDANCE |
| BS EN 16025-1:2013 | Thermal and/or sound insulating products in building construction. Bound EPS ballastings Requirements for factory premixed EPS dry plaster |
| 04/30118827 DC : DRAFT SEP 2004 | EN 15012 - SOIL AND WASTE DISCHARGE - PLASTICS PIPING SYSTEMS - SOIL AND WASTE DISCHARGE SYSTEMS WITHIN THE BUILDING STRUCTURE |
| BS EN 15534-1 : 2014 | COMPOSITES MADE FROM CELLULOSE-BASED MATERIALS AND THERMOPLASTICS (USUALLY CALLED WOOD-POLYMER COMPOSITES (WPC) OR NATURAL FIBRE COMPOSITES (NFC)) - PART 1: TEST METHODS FOR CHARACTERISATION OF COMPOUNDS AND PRODUCTS |
| DIN EN 14509:2013-12 | SELF-SUPPORTING DOUBLE SKIN METAL FACED INSULATING PANELS - FACTORY MADE PRODUCTS - SPECIFICATIONS |
| BS EN 16351:2015 | Timber structures. Cross laminated timber. Requirements |
| PREN 13165 : DRAFT 2010 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE RIGID POLYURETHANE FOAM (PU) PRODUCTS - SPECIFICATION |
| PREN 15501 : DRAFT 2015 | THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - FACTORY MADE EXPANDED PERLITE (EP) AND EXFOLIATED VERMICULITE (EV) PRODUCTS - SPECIFICATION |
| 13/30281348 DC : 0 | BS EN 13830 - CURTAIN WALLING - PRODUCT STANDARD |
| DIN EN 15651-4:2016-10 (Draft) | SEALANTS FOR NON-STRUCTURAL USE IN JOINTS IN BUILDINGS AND PEDESTRIAN WALKWAYS - PART 4: SEALANTS FOR PEDESTRIAN WALKWAYS |
| 10/30213971 DC : 0 | BS EN 13166 - THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE PHENOLIC FOAM (PF) PRODUCTS - SPECIFICATION |
| BS EN 15286:2013 | Agglomerated stone. Slabs and tiles for wall finishes (internal and external) |
| 11/30250549 DC : 0 | BS EN 14471 - CHIMNEYS - SYSTEM CHIMNEYS WITH PLASTIC FLUE LINERS - REQUIREMENTS AND TEST METHODS |
| 15/30294363 DC : 0 | BS ISO 17749 - THERMAL INSULATION PRODUCTS - SHEEP WOOL MAT AND BOARD |
| PREN 13164 : DRAFT 2010 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE EXTRUDED POLYSTYRENE FOAM (XPS) PRODUCTS - SPECIFICATION |
| PREN 13859-1 : DRAFT 2013 | FLEXIBLE SHEETS FOR WATERPROOFING - DEFINITIONS AND CHARACTERISTICS OF UNDERLAYS - PART 1: UNDERLAYS FOR DISCONTINUOUS ROOFING |
| UNI EN 15228 : 2009 | STRUCTURAL TIMBER - STRUCTURAL TIMBER PRESERVATIVE TREATED AGAINST BIOLOGICAL ATTACK |
| 08/30169552 DC : DRAFT APR 2008 | BS EN 13169 - THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE PRODUCTS OF EXPANDED PERLITE (EPB) - SPECIFICATION |
| DD CEN/TS 15534-1:2007 | Wood-plastics composites (WPC) Test methods for characterisation of WPC materials and products |
| 08/30169543 DC : DRAFT APR 2008 | BS EN 13166 - THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE PRODUCTS OF PHENOLIC FOAM (PF) - SPECIFICATION |
| I.S. EN 14305:2015 | THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - FACTORY MADE CELLULAR GLASS (CG) PRODUCTS - SPECIFICATION |
| PREN 14314 : DRAFT 2015 | THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - FACTORY MADE PHENOLIC FOAM (PF) PRODUCTS - SPECIFICATION |
| 03/115371 DC : DRAFT SEP 2003 | EN 14783 - FULLY SUPPORTED METAL SHEET AND STRIP FOR ROOF COVERINGS AND WALL FINISHES |
| 05/30136550 DC : 0 | PREN 14314 - THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - FACTORY MADE PHENOLIC FOAM (PF) PRODUCTS - SPECIFICATION |
| UNE-EN 13501-1:2007 | Fire classification of construction products and building elements - Part 1: Classification using data from reaction to fire tests |
| PREN 15014 : DRAFT 2014 | PLASTICS PIPING SYSTEMS - BURIED AND ABOVE GROUND PIPING COMPONENTS FOR WATER UNDER PRESSURE - REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR PIPES AND FITTINGS |
| PREN 490 : DRAFT 2011 | CONCRETE ROOFING TILES AND FITTINGS FOR ROOF COVERING AND WALL CLADDING - PRODUCT SPECIFICATIONS |
| PREN 14304 : DRAFT 2015 | THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - FACTORY MADE FLEXIBLE ELASTOMERIC FOAM (FEF) PRODUCTS - SPECIFICATION |
| PREN 14374 : DRAFT 2016 | TIMBER STRUCTURES - LAMINATED VENEER LUMBER (LVL) - REQUIREMENTS |
| PREN 492 : DRAFT 2010 | FIBRE-CEMENT SLATES AND FITTINGS - PRODUCT SPECIFICATION AND TEST METHODS |
| PREN 14783 : DRAFT 2012 | FULLY SUPPORTED METAL SHEET AND STRIP FOR ROOFING, EXTERNAL CLADDING AND INTERNAL LINING - PRODUCT SPECIFICATION AND REQUIREMENTS |
| NF EN 15715 : 2010 | THERMAL INSULATION PRODUCTS - INSTRUCTIONS FOR MOUNTING AND FIXING FOR REACTION TO FIRE TESTING - FACTORY MADE PRODUCTS |
| UNI EN 15497 : 2014 | STRUCTURAL FINGER JOINTED SOLID TIMBER - PERFORMANCE REQUIREMENTS AND MINIMUM PRODUCTION REQUIREMENTS |
| I.S. EN 14314:2015 | THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - FACTORY MADE PHENOLIC FOAM (PF) PRODUCTS - SPECIFICATION |
| ISO 24473:2008 | Fire tests — Open calorimetry — Measurement of the rate of production of heat and combustion products for fires of up to 40 MW |
| I.S. EN 60695-8-2:2017 | FIRE HAZARD TESTING - PART 8-2: HEAT RELEASE - SUMMARY AND RELEVANCE OF TEST METHODS |
| BS EN 14314:2015 | Thermal insulation products for building equipment and industrial installations. Factory made phenolic foam (PF) products. Specification |
| UNE-EN 14309:2017 | Thermal insulation products for building equipment and industrial installations - Factory made products of expanded polystyrene (EPS) - Specification |
| DIN EN 14308:2016-03 | THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - FACTORY MADE RIGID POLYURETHANE FOAM (PUR) AND POLYISOCYANURATE FOAM (PIR) PRODUCTS - SPECIFICATION |
| I.S. EN 14315-1:2013 | THERMAL INSULATING PRODUCTS FOR BUILDINGS - IN-SITU FORMED SPRAYED RIGID POLYURETHANE (PUR) AND POLYISOCYANURATE (PIR) FOAM PRODUCTS - PART 1: SPECIFICATION FOR THE RIGID FOAM SPRAY SYSTEM BEFORE INSTALLATION |
| DIN EN 14309:2016-03 | THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - FACTORY MADE PRODUCTS OF EXPANDED POLYSTYRENE (EPS) - SPECIFICATION |
| I.S. EN 492:2012 | Fibre-cement slates and fittings - Product specification and test methods |
| I.S. EN 14081-1:2016 | TIMBER STRUCTURES - STRENGTH GRADED STRUCTURAL TIMBER WITH RECTANGULAR CROSS SECTION - PART 1: GENERAL REQUIREMENTS |
| PREN 14305 : DRAFT 2015 | THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - FACTORY MADE CELLULAR GLASS (CG) PRODUCTS - SPECIFICATION |
| I.S. EN 15651-2:2017 | SEALANTS FOR NON-STRUCTURAL USE IN JOINTS IN BUILDINGS AND PEDESTRIAN WALKWAYS - PART 2: SEALANTS FOR GLAZING |
| NF EN 16000 : 2010 | PLASTICS PIPING SYSTEMS - SYSTEMS WITHIN THE BUILDING STRUCTURE - MOUNTING AND FIXING OF COMPONENTS IN THE TEST APPARATUS TO THERMAL ATTACK BY A SINGLE BURNING ITEM |
| I.S. EN 14304:2015 | THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - FACTORY MADE FLEXIBLE ELASTOMERIC FOAM (FEF) PRODUCTS - SPECIFICATION |
| BS EN 15814 : 2011 | POLYMER MODIFIED BITUMINOUS THICK COATINGS FOR WATERPROOFING - DEFINITIONS AND REQUIREMENTS |
| BS EN 60695-6-1 : 2005 | FIRE HAZARD TESTING - PART 6-1: SMOKE OBSCURATION - GENERAL GUIDANCE |
| BS EN 14304 : 2009 | THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - FACTORY MADE FLEXIBLE ELASTOMERIC FOAM (FEF) PRODUCTS - SPECIFICATION |
| PREN 14471 : DRAFT 2011 | CHIMNEYS - SYSTEM CHIMNEYS WITH PLASTIC FLUE LINERS - REQUIREMENTS AND TEST METHODS |
| S.R. CEN/TR 16988:2016 | ESTIMATION OF UNCERTAINTY IN THE SINGLE BURNING ITEM TEST |
| I.S. EN 124-6:2015 | GULLY TOPS AND MANHOLE TOPS FOR VEHICULAR AND PEDESTRIAN AREAS - PART 6: GULLY TOPS AND MANHOLE TOPS MADE OF POLYPROPYLENE (PP), POLYETHYLENE (PE) OR UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) |
| PREN 14306 : DRAFT 2015 | THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - FACTORY MADE CALCIUM SILICATE (CS) PRODUCTS - SPECIFICATION |
| 14/30303797 DC : 0 | BS EN 438-7 - HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 7: COMPACT LAMINATE AND HPL COMPOSITE PANELS FOR INTERNAL AND EXTERNAL WALL AND CEILING FINISHES |
| UNI EN 14064-1 : 2010 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - IN-SITU FORMED LOOSE-FILL MINERAL WOOL (MW) PRODUCTS - PART 1: SPECIFICATION FOR THE LOOSE-FILL PRODUCTS BEFORE INSTALLATION |
| I.S. EN 15814:2011 | POLYMER MODIFIED BITUMINOUS THICK COATINGS FOR WATERPROOFING - DEFINITIONS AND REQUIREMENTS |
| DIN EN 15101-1:2013-12 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - IN-SITU FORMED LOOSE FILL CELLULOSE (LFCI) PRODUCTS - PART 1: SPECIFICATION FOR THE PRODUCTS BEFORE INSTALLATION |
| ISO/TS 5658-1:2006 | Reaction to fire tests — Spread of flame — Part 1: Guidance on flame spread |
| UNI EN 15715 : 2009 | THERMAL INSULATION PRODUCTS - INSTRUCTIONS FOR MOUNTING AND FIXING FOR REACTION TO FIRE TESTING - FACTORY MADE PRODUCTS |
| UNE-EN 50399:2012 | Common test methods for cables under fire conditions - Heat release and smoke production measurement on cables during flame spread test - Test apparatus, procedures, results |
| I.S. CEN/TS 15117:2005 | GUIDANCE ON DIRECT AND EXTENDED APPLICATION |
| I.S. CEN TR 14819-2:2006 | SAFETY RECOMMENDATIONS FOR CABLEWAY INSTALLATIONS DESIGNED TO CARRY PERSONS - PREVENTION AND FIGHT AGAINST FIRE - PART 2: OTHER FUNICULAR RAILWAYS AND OTHER INSTALLATIONS |
| I.S. CEN TR 14819-1:2004 | SAFETY RECOMMENDATIONS FOR CABLEWAY INSTALLATIONS DESIGNED TO CARRY PERSONS - PREVENTION AND FIGHT AGAINST FIRE - PART 1: FUNICULAR RAILWAYS IN TUNNELS |
| PREN 14933 : DRAFT 2004 | LIGHT WEIGHT FILL AND INSULATION PRODUCTS FOR CIVIL ENGINEERING APPLICATIONS - FACTORY MADE PRODUCTS OF EXPANDED POLYSTYRENE (EPS) - SPECIFICATION |
| ASTM E 2536 : 2015 : REV A | Standard Guide for Assessment of Measurement Uncertainty in Fire Tests |
| EN 12467:2012+A2:2018 | Fibre-cement flat sheets - Product specification and test methods |
| UNI EN 438-8 : 2009 | HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 8: CLASSIFICATION AND SPECIFICATIONS FOR DESIGN LAMINATES |
| DIN EN 877:2010-01 | Cast iron pipes and fittings, their joints and accessories for the evacuation of water from buildings - Requirements, test methods and quality assurance (includes Amendment A1:2006 and Corrigendum AC:2008) |
| DIN EN 13163:2016-08 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE EXPANDED POLYSTYRENE (EPS) PRODUCTS - SPECIFICATION |
| DIN EN 13170:2015-04 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE PRODUCTS OF EXPANDED CORK (ICB) - SPECIFICATION |
| DIN EN 13164:2015-04 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE EXTRUDED POLYSTYRENE FOAM (XPS) PRODUCTS - SPECIFICATION |
| DIN EN 13165:2016-09 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE RIGID POLYURETHANE FOAM (PU) PRODUCTS - SPECIFICATION |
| DIN EN 13166:2016-09 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE PHENOLIC FOAM (PF) PRODUCTS - SPECIFICATION |
| DIN EN 13168:2015-04 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE WOOD WOOL (WW) PRODUCTS - SPECIFICATION |
| DIN EN 13162:2015-04 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE MINERAL WOOL (MW) PRODUCTS - SPECIFICATION |
| DIN EN 14246:2006-09 | Gypsum elements for suspended ceilings - Definitions, requirements and test methods |
| DIN EN 15266:2007-08 | Stainless steel pliable corrugated tubing kits in buildings for gas with an operating pressure up to 0,5 bar |
| DIN EN 14716:2005-03 | Stretched ceilings - Requirements and tests methods; German version EN 14716:2004 |
| DIN EN 14471:2015-03 | CHIMNEYS - SYSTEM CHIMNEYS WITH PLASTIC FLUE LINERS - REQUIREMENTS AND TEST METHODS |
| DIN EN 14782:2015-09 (Draft) | SELF-SUPPORTING METAL SHEET FOR ROOFING, EXTERNAL CLADDING AND INTERNAL LINING - PRODUCT SPECIFICATION AND REQUIREMENTS |
| DIN EN 14250:2010-05 | Timber structures - Product requirements for prefabricated structural members assembled with punched metal plate fasteners |
| DIN EN 12004:2014-02 | ADHESIVES FOR TILES - REQUIREMENTS, EVALUATION OF CONFORMITY, CLASSIFICATION AND DESIGNATION |
| DIN EN 14496:2016-02 (Draft) | GYPSUM BASED ADHESIVES FOR THERMAL/ACOUSTIC INSULATION COMPOSITE PANELS AND GYPSUM BOARDS - DEFINITIONS, REQUIREMENTS AND TEST METHODS |
| IEC 60695-8-1:2016 | Fire hazard testing - Part 8-1: Heat release - General guidance |
| UNE-EN 14080:2013 | Timber structures - Glued laminated timber and glued solid timber - Requirements |
| BS EN 544:2011 | Bitumen shingles with mineral and/or synthetic reinforcements. Product specification and test methods |
| UNE-EN 13830:2016 | Curtain walling - Product standard |
| PD IEC/TR 62222:2012 | Fire performance of communication cables installed in buildings |
| BS EN 14782:2006 | Self-supporting metal sheet for roofing, external cladding and internal lining. Product specification and requirements |
| BS EN ISO 15791-1:2013 | Plastics. Development and use of intermediate-scale fire tests for plastics products General guidance |
| UNE-EN 438-4:2016 | High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (Usually called Laminates) - Part 4: Classification and specifications for compact laminates of thickness 2 mm and greater |
| BS EN 13859-2:2014 | Flexible sheets for waterproofing. Definitions and characteristics of underlays Underlays for walls |
| BS EN 14716:2004 | Stretched ceilings. Requirements and test methods |
| I.S. EN 13830:2015 | CURTAIN WALLING - PRODUCT STANDARD |
| I.S. EN 13859-1:2014 | FLEXIBLE SHEETS FOR WATERPROOFING - DEFINITIONS AND CHARACTERISTICS OF UNDERLAYS - PART 1: UNDERLAYS FOR DISCONTINUOUS ROOFING |
| I.S. EN 14471:2013 | CHIMNEYS - SYSTEM CHIMNEYS WITH PLASTIC FLUE LINERS - REQUIREMENTS AND TEST METHODS |
| I.S. EN 14351-1:2006 | WINDOWS AND DOORS - PRODUCT STANDARD, PERFORMANCE CHARACTERISTICS - PART 1: WINDOWS AND EXTERNAL PEDESTRIAN DOORSETS WITHOUT RESISTANCE TO FIRE AND/OR SMOKE LEAKAGE CHARACTERISTICS |
| I.S. EN 13238:2010 | REACTION TO FIRE TESTS FOR BUILDING PRODUCTS - CONDITIONING PROCEDURES AND GENERAL RULES FOR SELECTION OF SUBSTRATES |
| DIN EN 13163:2017-02 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE EXPANDED POLYSTYRENE (EPS) PRODUCTS - SPECIFICATION |
| I.S. EN 13963:2014 | JOINTING MATERIALS FOR GYPSUM BOARDS - DEFINITIONS, REQUIREMENTS AND TEST METHODS |
| I.S. EN 13164:2012 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE EXTRUDED POLYSTYRENE FOAM (XPS) PRODUCTS - SPECIFICATION |
| I.S. EN 13163:2012 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE EXPANDED POLYSTYRENE (EPS) PRODUCTS - SPECIFICATION |
| I.S. EN 14496:2017 | GYPSUM BASED ADHESIVES FOR THERMAL/ACOUSTIC INSULATION COMPOSITE PANELS AND GYPSUM BOARDS - DEFINITIONS, REQUIREMENTS AND TEST METHODS |
| I.S. EN 13166:2012 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE PHENOLIC FOAM (PF) PRODUCTS - SPECIFICATION |
| I.S. EN 14209:2017 | PREFORMED PLASTERBOARD CORNICES - DEFINITIONS, REQUIREMENTS AND TEST METHODS |
| I.S. EN 13915:2017 | PREFABRICATED GYPSUM PLASTERBOARD PANELS WITH A CELLULAR PAPERBOARD CORE - DEFINITIONS, REQUIREMENTS AND TEST METHODS |
| I.S. EN 14783:2013 | FULLY SUPPORTED METAL SHEET AND STRIP FOR ROOFING, EXTERNAL CLADDING AND INTERNAL LINING - PRODUCT SPECIFICATION AND REQUIREMENTS |
| I.S. EN 13167:2012 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE CELLULAR GLASS (CG) PRODUCTS - SPECIFICATION |
| I.S. EN 13171:2012 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE WOOD FIBRE (WF) PRODUCTS - SPECIFICATION |
| I.S. EN ISO 15791-1:2013 | PLASTICS - DEVELOPMENT AND USE OF INTERMEDIATE-SCALE FIRE TESTS FOR PLASTICS PRODUCTS - PART 1: GENERAL GUIDANCE (ISO 15791-1:2014) |
| I.S. EN 13170:2012 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE PRODUCTS OF EXPANDED CORK (ICB) - SPECIFICATION |
| I.S. EN 520:2005 | GYPSUM PLASTERBOARDS - DEFINITIONS, REQUIREMENTS AND TEST METHODS |
| I.S. EN 13169:2012 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE EXPANDED PERLITE BOARD (EPB) PRODUCTS - SPECIFICATION |
| I.S. EN 1873:2014 | PREFABRICATED ACCESSORIES FOR ROOFING - INDIVIDUAL ROOFLIGHTS OF PLASTICS - PRODUCT SPECIFICATION AND TEST METHODS |
| I.S. EN 438-3:2016 | HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 3: CLASSIFICATION AND SPECIFICATIONS FOR LAMINATES LESS THAN 2 MM THICK INTENDED FOR BONDING TO SUPPORTING SUBSTRATES |
| I.S. EN 13162:2012 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE MINERAL WOOL (MW) PRODUCTS - SPECIFICATION |
| I.S. EN 438-4:2016 | HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 4: CLASSIFICATION AND SPECIFICATIONS FOR COMPACT LAMINATES OF THICKNESS 2 MM AND GREATER |
| I.S. EN 490:2011 | CONCRETE ROOFING TILES AND FITTINGS FOR ROOF COVERING AND WALL CLADDING - PRODUCT SPECIFICATIONS |
| I.S. EN 13859-2:2014 | FLEXIBLE SHEETS FOR WATERPROOFING - DEFINITIONS AND CHARACTERISTICS OF UNDERLAYS - PART 2: UNDERLAYS FOR WALLS |
| I.S. EN 14250:2010 | TIMBER STRUCTURES - PRODUCT REQUIREMENTS FOR PREFABRICATED STRUCTURAL MEMBERS ASSEMBLED WITH PUNCHED METAL PLATE FASTENERS |
| I.S. EN 12050-2:2015 | WASTEWATER LIFTING PLANTS FOR BUILDINGS AND SITES - PART 2: LIFTING PLANTS FOR FAECAL-FREE WASTEWATER |
| DIN EN 13238:2010-06 | Reaction to fire tests for building products - Conditioning procedures and general rules for selection of substrates |
| I.S. EN 13950:2014 | GYPSUM BOARD THERMAL/ACOUSTIC INSULATION COMPOSITE PANELS - DEFINITIONS, REQUIREMENTS AND TEST METHODS |
| I.S. EN 13964:2014 | SUSPENDED CEILINGS - REQUIREMENTS AND TEST METHODS |
| I.S. EN 12050-3:2015 | WASTEWATER LIFTING PLANTS FOR BUILDINGS AND SITES - PART 3: LIFTING PLANTS FOR LIMITED APPLICATIONS |
| I.S. EN 12050-4:2015 | WASTEWATER LIFTING PLANTS FOR BUILDINGS AND SITES - PART 4: NON-RETURN VALVES FOR FAECAL-FREE WASTEWATER AND WASTEWATER CONTAINING FAECAL MATTER |
| I.S. EN 438-6:2016 | HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 6: CLASSIFICATION AND SPECIFICATIONS FOR EXTERIOR-GRADE COMPACT LAMINATES OF THICKNESS 2 MM AND GREATER |
| I.S. EN 14190:2014 | GYPSUM BOARD PRODUCTS FROM REPROCESSING - DEFINITIONS, REQUIREMENTS AND TEST METHODS |
| I.S. EN 491:2011 | CONCRETE ROOFING TILES AND FITTINGS FOR ROOF COVERING AND WALL CLADDING - TEST METHODS |
| I.S. EN 12050-1:2015 | WASTEWATER LIFTING PLANTS FOR BUILDINGS AND SITES - PART 1: LIFTING PLANTS FOR WASTEWATER CONTAINING FAECAL MATTER |
| I.S. EN 494:2012 | FIBRE-CEMENT PROFILED SHEETS AND FITTINGS - PRODUCT SPECIFICATION AND TEST METHODS |
| I.S. EN 544:2011 | BITUMEN SHINGLES WITH MINERAL AND/OR SYNTHETIC REINFORCEMENTS - PRODUCT SPECIFICATION AND TEST METHODS |
| VDI 2055 Blatt 2:2013-10 | Thermal insulation of heated and refrigerated operational installations in the industry and in the building services - Technical basics for the verification of properties of insulating materials |
| UNE-EN 13915:2018 | Prefabricated gypsum plasterboard panels with a cellular paperboard core - Definitions, requirements and test methods |
| 05/30135337 DC : DRAFT JUN 2005 | EN 15266 - STAINLESS STEEL PLIABLE CORRUGATED TUBING SYSTEMS IN BUILDINGS FOR GAS WITH AN OPERATING PRESSURE UP TO 0,5 BAR |
| 11/30239909 DC : 0 | BS EN 15015 - PLASTICS PIPING SYSTEMS - HOT AND COLD WATER PIPING COMPONENTS - REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR PIPES AND FITTINGS |
| BS EN 12467 : 2012 | FIBRE-CEMENT FLAT SHEETS - PRODUCT SPECIFICATION AND TEST METHODS |
| 10/30213983 DC : 0 | BS EN 13170 - THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE PRODUCTS OF EXPANDED CORK (ICB) - SPECIFICATION |
| UNE-EN 15651-1:2017 | Sealants for non-structural use in joints in buildings and pedestrian walkways - Part 1: Sealants for facade elements |
| PD CEN/TR 14819-2:2005 | Safety recommendations for cableway installations designed to carry persons. Prevention and fight against fire Other funicular railways and other installations |
| 16/30332911 DC : 0 | BS EN 14496 - GYPSUM BASED ADHESIVES FOR THERMAL/ACOUSTIC INSULATION COMPOSITE PANELS AND GYPSUM BOARDS - DEFINITIONS, REQUIREMENTS AND TEST METHODS |
| DIN EN 1013:2015-03 | LIGHT TRANSMITTING SINGLE SKIN PROFILED PLASTICS SHEETS FOR INTERNAL AND EXTERNAL ROOFS, WALLS AND CEILINGS - REQUIREMENTS AND TEST METHODS |
| PD CEN/TR 16988:2016 | Estimation of uncertainty in the single burning item test |
| UNI EN 15012 : 2008 | PLASTICS PIPING SYSTEMS - SOIL AND WASTE DISCHARGE SYSTEMS WITHIN THE BUILDING STRUCTURE - PERFORMANCE CHARACTERISTICS FOR PIPES, FITTINGS AND THEIR JOINTS |
| BS EN 16240:2013 | Light transmitting flat solid polycarbonate (PC) sheets for internal and external use in roofs, walls and ceilings. Requirements and test methods |
| BS EN 15497:2014 | Structural finger jointed solid timber. Performance requirements and minimum production requirements |
| 12/30264370 DC : 0 | BS EN 14783 - FULLY SUPPORTED METAL SHEET AND STRIP FOR ROOFING, EXTERNAL CLADDING AND INTERNAL LINING - PRODUCT SPECIFICATION AND REQUIREMENTS |
| UNI EN 15037-5 : 2013 | PRECAST CONCRETE PRODUCTS - BEAM-AND-BLOCK FLOOR SYSTEMS - PART 5: LIGHTWEIGHT BLOCKS FOR SIMPLE FORMWORK |
| 14/30311128 DC : 0 | BS EN 14716 - STRETCHED CEILINGS - REQUIREMENTS AND TEST METHODS |
| PREN 14782 : DRAFT 2015 | SELF-SUPPORTING METAL SHEET FOR ROOFING, EXTERNAL CLADDING AND INTERNAL LINING - PRODUCT SPECIFICATION AND REQUIREMENTS |
| 13/30258117 DC : 0 | BS EN 15101-1 - THERMAL INSULATION PRODUCTS FOR BUILDINGS - IN-SITU FORMED LOOSE FILL CELLULOSE (LFCI) PRODUCTS - PART 1: SPECIFICATION FOR THE PRODUCTS BEFORE INSTALLATION |
| BS EN 14306:2015 | Thermal insulation products for building equipment and industrial installations. Factory made calcium silicate (CS) products. Specification |
| 14/30303791 DC : 0 | BS EN 438-6 - HIGH-PRESSURE DECORATIVE (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 6: CLASSIFICATION AND SPECIFICATIONS FOR EXTERIOR-GRADE COMPACT LAMINATES OF THICKNESS 2 MM AND GREATER |
| UNI CEN/TS 15912 : 2012 | DURABILITY OF REACTION TO FIRE PERFORMANCE - CLASSES OF FIRE-RETARDANT TREATED WOOD-BASED PRODUCT IN INTERIOR AND EXTERIOR END USE APPLICATIONS |
| DD CEN/TS 15117:2005 | Guidance on direct and extended application |
| DIN EN 15283-1:2009-12 | Gypsum boards with fibrous reinforcement - Definitions, requirements and test methods - Part 1: Gypsum boards with mat reinforcement (includes Amendment A1:2009) |
| UNI EN 15283-2 : 2009 | GYPSUM BOARDS WITH FIBROUS REINFORCEMENT - DEFINITIONS, REQUIREMENTS AND TEST METHODS - PART 2: GYPSUM FIBRE BOARDS |
| 17/30355239 DC : 0 | BS ISO 4586-4 - HIGH-PRESSURE DECORATIVE LAMINATES (HPL, HPDL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 4: CLASSIFICATION AND SPECIFICATIONS FOR COMPACT LAMINATES OF THICKNESS 2 MM AND GREATER |
| 16/30304294 DC : 0 | BS EN 16989 - RAILWAY APPLICATIONS - FIRE PROTECTION ON RAILWAY VEHICLES - FIRE BEHAVIOUR TEST FOR A COMPLETE SEAT |
| 15/30324708 DC : DRAFT MAY 2015 | PD CEN/TS 115-4 - SAFETY OF ESCALATORS AND MOVING WALKS - PART 4: INTERPRETATIONS RELATED TO EN 115 FAMILY OF STANDARDS |
| I.S. EN 50399:2011 | COMMON TEST METHODS FOR CABLES UNDER FIRE CONDITIONS - HEAT RELEASE AND SMOKE PRODUCTION MEASUREMENT ON CABLES DURING FLAME SPREAD TEST - TEST APPARATUS, PROCEDURES, RESULTS |
| 11/30233179 DC : 0 | BS EN 15102:2007/A1 - DECORATIVE WALL COVERINGS - ROLL AND PANEL PRODUCT |
| 13/30273036 DC : 0 | BS EN 13859-1 - FLEXIBLE SHEETS FOR WATERPROOFING - DEFINITIONS AND CHARACTERISTICS OF UNDERLAYS - PART 1: UNDERLAYS FOR DISCONTINUOUS ROOFING |
| 12/30258334 DC : 0 | BS EN 1013 - LIGHT TRANSMITTING SINGLE SKIN PROFILED PLASTIC SHEETS FOR INTERNAL AND EXTERNAL ROOFS, WALLS AND CEILINGS - REQUIREMENTS AND TEST METHODS |
| I.S. EN 1794-3:2016 | ROAD TRAFFIC NOISE REDUCING DEVICES - NON-ACOUSTIC PERFORMANCE - PART 3: REACTION TO FIRE - BURNING BEHAVIOUR OF NOISE REDUCING DEVICES AND CLASSIFICATION |
| BS EN 15701:2016 | Plastics. Thermoplastic jackets for insulation products for building equipment and industrial installations. Requirements and test methods |
| PREN 13167 : DRAFT 2010 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE CELLULAR GLASS (CG) PRODUCTS - SPECIFICATION |
| 08/30169534 DC : DRAFT APR 2008 | BS EN 13163 - THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE PRODUCTS OF EXPANDED POLYSTYRENE (EPS) - SPECIFICATION |
| UNI EN 15564 : 2009 | PRECAST CONCRETE PRODUCTS - RESIN BOUND CONCRETE - REQUIREMENTS AND TEST METHODS |
| PREN 12467 : DRAFT 2010 | FIBRE-CEMENT FLAT SHEETS - PRODUCT SPECIFICATION AND TEST METHODS |
| DIN EN 15715:2010-04 | Thermal insulation products - Instructions for mounting and fixing for reaction to fire testing - Factory made products |
| UNI EN 14320-1 : 2013 | THERMAL INSULATING PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - IN-SITU FORMED SPRAYED RIGID POLYURETHANE (PUR) AND POLYISOCYANURATE FOAM (PIR) PRODUCTS - PART 1: SPECIFICATION FOR THE RIGID FOAM SPRAY SYSTEM BEFORE INSTALLATION |
| BS ISO 2219:2010 | Thermal insulation products for buildings. Factory-made products of expanded cork (ICB). Specification |
| BS EN 15423:2008 | Ventilation for buildings. Fire precaution for air distribution systems in buildings |
| DIN EN 15701:2015-02 (Draft) | PLASTICS - THERMOPLASTIC JACKETS FOR INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - REQUIREMENTS AND TEST METHODS |
| BS ISO 10840:2008 | Plastics. Guidance for the use of standard fire tests |
| UNE-EN 14305:2017 | Thermal insulation products for building equipment and industrial installations - Factory made cellular glass (CG) products - Specification |
| 12/30270374 DC : 0 | BS EN 15501 - THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - FACTORY MADE EXPANDED PERLITE (EP) AND EXFOLIATED VERMICULITE (EV) PRODUCTS - SPECIFICATION |
| 17/30363842 DC : 0 | BS ISO 21927-2 - SMOKE AND HEAT CONTROL SYSTEMS - PART 2: SPECIFICATION FOR NATURAL SMOKE AND HEAT EXHAUST VENTILATORS |
| 15/30315072 DC : DRAFT MAY 2015 | BS EN 14306 - THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - FACTORY MADE CALCIUM SILICATE (CS) PRODUCTS - SPECIFICATION |
| 14/30303779 DC : 0 | BS EN 438-4 - HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 4: CLASSIFICATION AND SPECIFICATIONS FOR COMPACT LAMINATES OF THICKNESS 2 MM AND GREATER |
| CEI EN 60695-8-1 : 2009 | FIRE HAZARD TESTING - PART 8-1: HEAT RELEASE - GENERAL GUIDANCE |
| UNE-EN 124-5:2015 | Gully tops and manhole tops for vehicular and pedestrian areas - Part 5: Gully tops and manhole tops made of composite materials |
| 08/30169549 DC : DRAFT APR 2008 | BS EN 13168 - THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE WOOD WOOL (WW) PRODUCTS - SPECIFICATION |
| 10/30213977 DC : 0 | BS EN 13168 - THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE WOOD WOOL (WW) PRODUCTS - SPECIFICATION |
| DIN EN 14315-1:2013-04 | THERMAL INSULATING PRODUCTS FOR BUILDINGS - IN-SITU FORMED SPRAYED RIGID POLYURETHANE (PUR) AND POLYISOCYANURATE (PIR) FOAM PRODUCTS - PART 1: SPECIFICATION FOR THE RIGID FOAM SPRAY SYSTEM BEFORE INSTALLATION |
| EN 115-1:2017 | Safety of escalators and moving walks - Part 1: Construction and installation |
| BS EN 14509:2013 | Self-supporting double skin metal faced insulating panels. Factory made products. Specifications |
| BS EN 16069 : 2012 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE PRODUCTS OF POLYETHYLENE FOAM (PEF) - SPECIFICATION |
| 12/30265313 DC : 0 | BS EN 124-6 - GULLY TOPS AND MANHOLE TOPS FOR VEHICULAR AND PEDESTRIAN AREAS - PART 6: GULLY TOPS AND MANHOLE TOPS MADE FROM POLYPROPYLENE (PP) OR POLYVINYL-CHLORIDE (PVC-U) |
| BS EN 15228:2009 | Structural timber. Structural timber preservative treated against biological attack |
| 09/30194024 DC : DRAFT FEB 2009 | BS EN 15912 - DURABILITY OF REACTION TO FIRE PERFORMANCES - CLASSES OF FIRE RETARDANT TREATED WOOD-BASED PRODUCT IN INTERIOR AND EXTERIOR END USE APPLICATIONS |
| BS ISO 29903:2012 | Guidance for comparison of toxic gas data between different physical fire models and scales |
| 04/30126133 DC : DRAFT NOV 2004 | EN 15100-1 - THERMAL INSULATING PRODUCTS FOR BUILDINGS - IN-SITU FORMED UREAFORMALDEHYDE FOAM (UF) PRODUCTS - PART 1: SPECIFICATION FOR THE FOAM SYSTEM BEFORE INSTALLATION |
| 04/30113509 DC : DRAFT MAY 2004 | BS EN 14934 - THERMAL INSULATION OF ROAD AND RAILWAYS AND EMBANKMENT FILLING - FACTORY MADE PRODUCTS OF EXTRUDED POLYSTYRENE FOAM (XPS) - SPECIFICATION |
| UNE-EN 60695-8-1:2017 | Fire hazard testing - Part 8-1: Heat release - General guidance |
| 11/30238648 DC : DRAFT FEB 2011 | BS EN 16240 - LIGHT TRANSMITTING FLAT SOLID POLYCARBONATE (PC) SHEETS FOR INTERNAL AND EXTERNAL ROOFS, WALLS AND CEILINGS - REQUIREMENTS AND TEST METHODS |
| UNI EN 13245-2 : 2009 | PLASTICS - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) PROFILES FOR BUILDING APPLICATIONS - PART 2: PVC-U PROFILES AND PVC-UE PROFILES FOR INTERNAL AND EXTERNAL WALL AND CEILING FINISHES |
| 10/30213974 DC : 0 | BS EN 13167 - THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE CELLULAR GLASS (CG) PRODUCTS - SPECIFICATION |
| 08/30185977 DC : DRAFT DEC 2008 | BS EN 438-9 - HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 9: CLASSIFICATION AND SPECIFICATIONS FOR ALTERNATIVE CORE LAMINATES |
| 08/30169556 DC : DRAFT APR 2008 | BS EN 13170 - THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE PRODUCTS OF EXPANDED CORK (ICB) - SPECIFICATION |
| UNE-EN 14320-1:2013 | Thermal insulating products for building equipment and industrial installations - In-situ formed sprayed rigid polyurethane (PUR) and polyisocyanurate foam (PIR) products - Part 1: Specification for the rigid foam spray system before installation |
| DIN EN 14307:2016-03 | THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - FACTORY MADE EXTRUDED POLYSTYRENE FOAM (XPS) PRODUCTS - SPECIFICATION |
| BS EN 16000:2010 | Plastics piping systems. Systems within the building structure. Mounting and fixing of components in the test apparatus to thermal attack by a single burning item |
| UNE-EN 14313:2017 | Thermal insulation products for building equipment and industrial installations - Factory made polyethylene foam (PEF) products - Specification |
| BS EN 15389:2008 | Industrial valves. Performance characteristics of thermoplastic valves when used as construction products |
| PREN 13162 : DRAFT 2010 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE MINERAL WOOL (MW) PRODUCTS - SPECIFICATION |
| DIN EN 16153:2015-05 | LIGHT TRANSMITTING FLAT MULTIWALL POLYCARBONATE (PC) SHEETS FOR INTERNAL AND EXTERNAL USE IN ROOFS, WALLS AND CEILINGS - REQUIREMENTS AND TEST METHODS |
| I.S. EN 16351:2015 | TIMBER STRUCTURES - CROSS LAMINATED TIMBER - REQUIREMENTS |
| PREN 16755 : DRAFT 2014 | DURABILITY OF REACTION TO FIRE PERFORMANCE - CLASSES OF FIRERETARDANT TREATED WOOD PRODUCTS IN INTERIOR AND EXTERIOR END USE APPLICATIONS |
| PREN 14209 : DRAFT 2016 | PREFORMED PLASTERBOARD CORNICES - DEFINITIONS, REQUIREMENTS AND TEST METHODS |
| BS EN 15101-1:2013 | Thermal insulation products for buildings. In-situ formed loose fill cellulose (LFCI) products Specification for the products before installation |
| DIN EN 14314:2016-03 | THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - FACTORY MADE PHENOLIC FOAM (PF) PRODUCTS - SPECIFICATION |
| IEC TR 60695-8-2:2008 | Fire hazard testing - Part 8-2: Heat release - Summary and relevance of test methods |
| DIN EN 14303:2016-08 | THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - FACTORY MADE MINERAL WOOL (MW) PRODUCTS - SPECIFICATION |
| DIN EN 15501:2016-03 | THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - FACTORY MADE EXPANDED PERLITE (EP) AND EXFOLIATED VERMICULITE (EV) PRODUCTS - SPECIFICATION |
| BS EN 14064-1:2010 | Thermal insulation products for buildings. In-situ formed loose-fill mineral wool (MW) products Specification for the loose-fill products before installation |
| I.S. EN 115-1:2017 | SAFETY OF ESCALATORS AND MOVING WALKS - PART 1: CONSTRUCTION AND INSTALLATION |
| BS EN 1013 : 2012 | LIGHT TRANSMITTING SINGLE SKIN PROFILED PLASTICS SHEETS FOR INTERNAL AND EXTERNAL ROOFS, WALLS AND CEILINGS - REQUIREMENTS AND TEST METHODS |
| I.S. EN 16025-1:2013 | THERMAL AND/OR SOUND INSULATING PRODUCTS IN BUILDING CONSTRUCTION - BOUND EPS BALLASTINGS - PART 1: REQUIREMENTS FOR FACTORY PREMIXED EPS DRY PLASTER |
| I.S. EN 16240:2013 | LIGHT TRANSMITTING FLAT SOLID POLYCARBONATE (PC) SHEETS FOR INTERNAL AND EXTERNAL USE IN ROOFS, WALLS AND CEILINGS - REQUIREMENTS AND TEST METHODS |
| I.S. EN 14309:2015 | THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - FACTORY MADE PRODUCTS OF EXPANDED POLYSTYRENE (EPS) - SPECIFICATION |
| EN 438-8:2009 | High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (Usually called Laminates) - Part 8: Classification and specifications for design laminates |
| BS EN 16724:2016 | Thermal insulation products for building applications. Instructions for mounting and fixing for determination of the reaction to fire testing of external thermal Insulation composite systems (ETICS) |
| BS EN 50399:2011 | Common test methods for cables under fire conditions. Heat release and smoke production measurement on cables during flame spread test. Test apparatus, procedures, results |
| PREN 438-7 : DRAFT 2014 | HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 7: COMPACT LAMINATE AND HPL COMPOSITE PANELS FOR INTERNAL AND EXTERNAL WALL AND CEILING FINISHES |
| BS EN 492 : 2012 | FIBRE-CEMENT SLATES AND FITTINGS - PRODUCT SPECIFICATION AND TEST METHODS |
| UNE-CEN/TS 15679:2009 EX | Thermal Modified Timber - Definitions and characteristics |
| UNE-EN 124-6:2015 | Gully tops and manhole tops for vehicular and pedestrian areas - Part 6: Gully tops and manhole tops made of polypropylene (PP), polyethylene (PE) or unplasticized poly(vinyl chloride) (PVC-U) |
| PREN 14190 : DRAFT 2011 | GYPSUM PLASTERBOARD PRODUCTS FROM PROCESSING - DEFINITIONS, REQUIREMENTS AND TEST METHODS |
| I.S. EN 124-5:2015 | GULLY TOPS AND MANHOLE TOPS FOR VEHICULAR AND PEDESTRIAN AREAS - PART 5: GULLY TOPS AND MANHOLE TOPS MADE OF COMPOSITE MATERIALS |
| PREN 14509 : DRAFT 2013 | SELF-SUPPORTING DOUBLE SKIN METAL FACED INSULATING PANELS - FACTORY MADE PRODUCTS - SPECIFICATIONS |
| I.S. EN 15651-1:2017 | SEALANTS FOR NON-STRUCTURAL USE IN JOINTS IN BUILDINGS AND PEDESTRIAN WALKWAYS - PART 1: SEALANTS FOR FACADE ELEMENTS |
| I.S. EN 60695-6-1:2005 | FIRE HAZARD TESTING - PART 6-1: SMOKE OBSCURATION - GENERAL GUIDANCE |
| UNI EN 16025-1 : 2013 | THERMAL AND/OR SOUND INSULATING PRODUCTS IN BUILDING CONSTRUCTION - BOUND EPS BALLASTINGS - PART 1: REQUIREMENTS FOR FACTORY PREMIXED EPS DRY PLASTER |
| UNI EN 14319-1 : 2013 | THERMAL INSULATING PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - IN-SITU FORMED DISPENSED RIGID POLYURETHANE (PUR) AND POLYISOCYANURATE FOAM (PIR) PRODUCTS - PART 1: SPECIFICATION FOR THE RIGID FOAM DISPENSED SYSTEM BEFORE INSTALLATION |
| PREN 14307 : DRAFT 2015 | THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - FACTORY MADE EXTRUDED POLYSTYRENE FOAM (XPS) PRODUCTS - SPECIFICATION |
| 14/30297456 DC : 0 | BS EN 15013 - PLASTICS PIPING SYSTEMS - NON-PRESSURE DRAINAGE AND SEWERAGE PIPING COMPONENTS BURIED IN GROUND - REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR PIPES AND FITTINGS |
| UNE-CEN/TS 15912:2012 EX | Durability of reaction to fire performance - Classes of fire-retardant treated wood-based product in interior and exterior end use applications |
| PREN 15012 : DRAFT 2014 | PLASTICS PIPING SYSTEMS - BURIED AND ABOVE GROUND PIPING COMPONENTS FOR NON PRESSURE SOIL AND WASTE DISCHARGE WITHIN THE BUILDING STRUCTURE - REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR PIPES AND FITTINGS |
| PREN 13950 : DRAFT 2011 | GYPSUM BOARD THERMAL/ACOUSTIC INSULATION COMPOSITE PANELS - DEFINITIONS, REQUIREMENTS AND TEST METHODS |
| PREN 13915 : DRAFT 2016 | PREFABRICATED GYPSUM PLASTERBOARD PANELS WITH A CELLULAR PAPERBOARD CORE - DEFINITIONS, REQUIREMENTS AND TEST METHODS |
| PREN 15015 : DRAFT 2014 | PLASTICS PIPING SYSTEMS - HOT AND COLD WATER PIPING COMPONENTS - REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR PIPES AND FITTINGS |
| ISO/TS 5660-3:2012 | Reaction-to-fire tests — Heat release, smoke production and mass loss rate — Part 3: Guidance on measurement |
| UNI EN 13501-1 : 2009 | FIRE CLASSIFICATION OF CONSTRUCTION PRODUCTS AND BUILDING ELEMENTS - PART 1: CLASSIFICATION USING DATA FROM REACTION TO FIRE TESTS |
| ISO 4586-3:2015 | High-pressure decorative laminates (HPL, HPDL) Sheets based on thermosetting resins (Usually called Laminates) Part 3: Classification and specifications for laminates less than 2 mm thick and intended for bonding to supporting substrates |
| BS EN 13501-1 : 2007 | FIRE CLASSIFICATION OF CONSTRUCTION PRODUCTS AND BUILDING ELEMENTS - PART 1: CLASSIFICATION USING DATA FROM REACTION TO FIRE TESTS |
| I.S. EN 15423:2008 | VENTILATION FOR BUILDINGS - FIRE PRECAUTIONS FOR AIR DISTRIBUTION SYSTEMS IN BUILDINGS |
| UNE-EN 490:2012 | Concrete roofing tiles and fittings for roof covering and wall cladding - Product specifications |
| I.S. EN 14509:2013 | SELF-SUPPORTING DOUBLE SKIN METAL FACED INSULATING PANELS - FACTORY MADE PRODUCTS - SPECIFICATIONS |
| DIN EN 13171:2015-04 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE WOOD FIBRE (WF) PRODUCTS - SPECIFICATION |
| DIN EN 13167:2015-04 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE CELLULAR GLASS (CG) PRODUCTS - SPECIFICATION |
| DIN EN 494:2015-12 | FIBRE-CEMENT PROFILED SHEETS AND FITTINGS - PRODUCT SPECIFICATION AND TEST METHODS |
| DIN EN 438-3:2016-06 | HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 3: CLASSIFICATION AND SPECIFICATIONS FOR LAMINATES LESS THAT 2 MM THICK INTENDED FOR BONDING TO SUPPORTING SUBSTRATES |
| DIN EN 438-7:2005-04 | High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (usually called laminates) - Part 7: Compact laminate and HPL composite panels for internal and external wall and ceiling finishes; German version EN 438-7:2005 |
| DIN EN 438-4:2016-06 | HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 4: CLASSIFICATION AND SPECIFICATIONS FOR COMPACT LAMINATES OF THICKNESS 2 MM AND GREATER |
| DIN EN 12050-4:2015-05 | WASTEWATER LIFTING PLANTS FOR BUILDINGS AND SITES - PART 4: NON-RETURN VALVES FOR FAECAL-FREE WASTEWATER AND WASTEWATER CONTAINING FAECAL MATTER |
| DIN EN 12050-1:2015-05 | WASTEWATER LIFTING PLANTS FOR BUILDINGS AND SITES - PART 1: LIFTING PLANTS FOR WASTEWATER CONTAINING FAECAL MATTER |
| DIN EN 13950:2014-09 | GYPSUM BOARD THERMAL/ACOUSTIC INSULATION COMPOSITE PANELS - DEFINITIONS, REQUIREMENTS AND TEST METHODS |
| DIN EN 13915:2016-02 (Draft) | PREFABRICATED GYPSUM PLASTERBOARD PANELS WITH A CELLULAR PAPERBOARD CORE - DEFINITIONS, REQUIREMENTS AND TEST METHODS |
| DIN EN 13963:2014-09 | JOINTING MATERIALS FOR GYPSUM BOARDS - DEFINITIONS, REQUIREMENTS AND TEST METHODS |
| DIN EN 13964:2014-08 | SUSPENDED CEILINGS - REQUIREMENTS AND TEST METHODS |
| DIN EN 12050-3:2015-08 | WASTEWATER LIFTING PLANTS FOR BUILDINGS AND SITES - PART 3: LIFTING PLANTS FOR LIMITED APPLICATIONS |
| UNE-EN 14509:2014 | Self-supporting double skin metal faced insulating panels - Factory made products - Specifications |
| UNE-EN 14250:2010 | Timber structures - Product requirements for prefabricated structural members assembled with punched metal plate fasteners |
| BS EN 13169 : 2012 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE EXPANDED PERLITE BOARD (EPB) PRODUCTS - SPECIFICATION |
| BS EN 494 : 2012 | FIBRE-CEMENT PROFILED SHEETS AND FITTINGS - PRODUCT SPECIFICATION AND TEST METHODS |
| UNE-EN 12050-3:2015 | Wastewater lifting plants for buildings and sites - Part 3: Lifting plants for limited applications |
| UNE-EN 12050-4:2015 | Wastewater lifting plants for buildings and sites - Part 4: Non-return valves for faecal-free wastewater and wastewater containing faecal matter |
| I.S. EN 14080:2013 | TIMBER STRUCTURES - GLUED LAMINATED TIMBER AND GLUED SOLID TIMBER - REQUIREMENTS |
| EN 13830:2015 | Curtain walling - Product standard |
| EN 14064-1:2010 | Thermal insulation products for buildings - In-situ formed loose-fill mineral wool (MW) products - Part 1: Specification for the loose-fill products before installation |
| UNE-EN 12004:2008 | Adhesives for tiles - Requirements, evaluation of conformity, classification and designation |
| EN 13501-1:2007+A1:2009 | Fire classification of construction products and building elements - Part 1: Classification using data from reaction to fire tests |
| CEN/TS 115-4:2015 | Safety of escalators and moving walks - Part 4: Interpretations related to EN 115 family of standards |
| EN 15283-1:2008+A1:2009 | Gypsum boards with fibrous reinforcement - Definitions, requirements and test methods - Part 1: Gypsum boards with mat reinforcement |
| EN ISO 15791-1:2013 | Plastics - Development and use of intermediate-scale fire tests for plastics products - Part 1: General guidance (ISO 15791-1:2014) |
| EN 13964:2014 | Suspended ceilings - Requirements and test methods |
| EN 16240:2013 | Light transmitting flat solid polycarbonate (PC) sheets for internal and external use in roofs, walls and ceilings - Requirements and test methods |
| EN 544:2011 | Bitumen shingles with mineral and/or synthetic reinforcements - Product specification and test methods |
| UNI EN 14509 : 2013 | SELF-SUPPORTING DOUBLE SKIN METAL FACED INSULATING PANELS - FACTORY MADE PRODUCTS - SPECIFICATIONS |
| UNI EN ISO 15791-1 : 2014 | PLASTICS - DEVELOPMENT AND USE OF INTERMEDIATE-SCALE FIRE TESTS FOR PLASTICS PRODUCTS - PART 1: GENERAL GUIDANCE |
| UNI EN 14783 : 2013 | FULLY SUPPORTED METAL SHEET AND STRIP FOR ROOFING, EXTERNAL CLADDING AND INTERNAL LINING - PRODUCT SPECIFICATION AND REQUIREMENTS |
| UNI EN 13859-2 : 2014 | FLEXIBLE SHEETS FOR WATERPROOFING - DEFINITIONS AND CHARACTERISTICS OF UNDERLAYS - PART 2: UNDERLAYS FOR WALLS |
| UNI EN 520 : 2009 | GYPSUM PLASTERBOARDS - DEFINITIONS, REQUIREMENTS AND TEST METHODS |
| UNI EN 12004 : 2012 | ADHESIVES FOR TILES - REQUIREMENTS, EVALUATION OF CONFORMITY, CLASSIFICATION AND DESIGNATION |
| UNI EN 13859-1 : 2014 | FLEXIBLE SHEETS FOR WATERPROOFING - DEFINITIONS AND CHARACTERISTICS OF UNDERLAYS - PART 1: UNDERLAYS FOR DISCONTINUOUS ROOFING |
| UNI EN 14080 : 2013 | TIMBER STRUCTURES - GLUED LAMINATED TIMBER AND GLUED SOLID TIMBER - REQUIREMENTS |
| UNI EN 14800 : 2007 | CORRUGATED SAFETY METAL HOSE ASSEMBLIES FOR THE CONNECTION DOMESTIC APPLIANCES USING GASEOUS FUELS |
| EN 490:2011+A1:2017 | Concrete roofing tiles and fittings for roof covering and wall cladding - Product specifications |
| UNI EN 14190 : 2014 | GYPSUM BOARD PRODUCTS FROM REPROCESSING - DEFINITIONS, REQUIREMENTS AND TEST METHODS |
| UNI EN 13964 : 2014 | SUSPENDED CEILINGS - REQUIREMENTS AND TEST METHODS |
| UNI EN 14250 : 2010 | TIMBER STRUCTURES - PRODUCT REQUIREMENTS FOR PREFABRICATED STRUCTURAL MEMBERS ASSEMBLED WITH PUNCHED METAL PLATE FASTENERS |
| UNI EN 544 : 2011 | BITUMEN SHINGLES WITH MINERAL AND/OR SYNTHETIC REINFORCEMENTS - PRODUCT SPECIFICATION AND TEST METHODS |
| UNI EN 14246 : 2006 | GYPSUM ELEMENTS FOR SUSPENDED CEILINGS - DEFINITIONS, REQUIREMENTS AND TEST METHODS |
| UNI EN 13950 : 2014 | GYPSUM BOARD THERMAL/ACOUSTIC INSULATION COMPOSITE PANELS - DEFINITIONS, REQUIREMENTS AND TEST METHODS |
| UNI EN 13963 : 2014 | JOINTING MATERIALS FOR GYPSUM BOARDS - DEFINITIONS, REQUIREMENTS AND TEST METHODS |
| UNI EN 491 : 2011 | CONCRETE ROOFING TILES AND FITTINGS FOR ROOF COVERING AND WALL CLADDING - TEST METHODS |
| UNI EN 15619 : 2014 | RUBBER OR PLASTIC COATED FABRICS - SAFETY OF TEMPORARY STRUCTURES (TENTS) - SPECIFICATION FOR COATED FABRICS INTENDED FOR TENTS AND RELATED STRUCTURES |
| UNI EN 13238 : 2010 | REACTION TO FIRE TESTS FOR BUILDING PRODUCTS - CONDITIONING PROCEDURES AND GENERAL RULES FOR SELECTION OF SUBSTRATES |
| DIN EN 16351:2015-12 | Timber structures - Cross laminated timber - Requirements |
| I.S. EN 15497:2014 | STRUCTURAL FINGER JOINTED SOLID TIMBER - PERFORMANCE REQUIREMENTS AND MINIMUM PRODUCTION REQUIREMENTS |
| 12/30254141 DC : 0 | BS EN 15651-4 - SEALANTS FOR NON-STRUCTURAL USE IN JOINTS IN BUILDINGS AND PEDESTRIAN WALKWAYS - PART 4: SEALANTS FOR PEDESTRIAN WALKWAYS |
| I.S. EN 12004:2007 | ADHESIVES FOR TILES - REQUIREMENTS, EVALUATION OF CONFORMITY, CLASSIFICATION AND DESIGNATION |
| BS EN 124-5:2015 | Gully tops and manhole tops for vehicular and pedestrian areas Gully tops and manhole tops made of composite materials |
| 15/30315090 DC : DRAFT MAY 2015 | BS EN 14304 - THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - FACTORY MADE FLEXIBLE ELASTOMERIC FOAM (FEF) PRODUCTS - SPECIFICATION |
| 10/30233185 DC : 0 | BS EN 12467 - FIBRE-CEMENT FLAT SHEETS - PRODUCT SPECIFICATION AND TEST METHODS |
| DIN EN 15651-2:2016-10 (Draft) | SEALANTS FOR NON-STRUCTURAL USE IN JOINTS IN BUILDINGS AND PEDESTRIAN WALKWAYS - PART 2: SEALANTS FOR GLAZING |
| PREN 13170 : DRAFT 2010 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE PRODUCTS OF EXPANDED CORK (ICB) - SPECIFICATION |
| 05/30136552 DC : 0 | PREN 14304 - THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - FACTORY MADE FLEXIBLE ELASTOMERIC FOAM (FEF) - SPECIFICATION |
| PREN 14303 : DRAFT 2015 | THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - FACTORY MADE MINERAL WOOL (MW) PRODUCTS - SPECIFICATION |
| UNI EN 14315-1 : 2013 | THERMAL INSULATING PRODUCTS FOR BUILDINGS - IN-SITU FORMED SPRAYED RIGID POLYURETHANE (PUR) AND POLYISOCYANURATE (PIR) FOAM PRODUCTS - PART 1: SPECIFICATION FOR THE RIGID FOAM SPRAY SYSTEM BEFORE INSTALLATION |
| 12/30254135 DC : 0 | BS EN 15651-2 - SEALANTS FOR NON-STRUCTURAL USE IN JOINTS IN BUILDINGS AND PEDESTRIAN WALKWAYS - PART 2: SEALANTS FOR GLAZING |
| UNI EN 16000 : 2010 | PLASTICS PIPING SYSTEMS - SYSTEMS WITHIN THE BUILDING STRUCTURE - MOUNTING AND FIXING OF COMPONENTS IN THE TEST APPARATUS TO THERMAL ATTACK BY A SINGLE BURNING ITEM |
| UNI EN 14318-1 : 2013 | THERMAL INSULATING PRODUCTS FOR BUILDINGS - IN-SITU FORMED DISPENSED RIGID POLYURETHANE (PUR) AND POLYISOCYANURATE (PIR) FOAM PRODUCTS - PART 1: SPECIFICATION FOR THE RIGID FOAM DISPENSED SYSTEM BEFORE INSTALLATION |
| PREN 544 : DRAFT 2010 | BITUMEN SHINGLES WITH MINERAL AND/OR SYNTHETIC REINFORCEMENTS - PRODUCT SPECIFICATION AND TEST METHODS |
| PREN 13168 : DRAFT 2010 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE WOOD WOOL (WW) PRODUCTS - SPECIFICATION |
| BS EN 15037-5:2013 | Precast concrete products. Beam-and-block floor systems Lightweight blocks for simple formwork |
| 13/30263194 DC : 0 | BS EN 16623 - PAINTS AND VARNISHES - REACTIVE COATINGS FOR FIRE PROTECTION OF METALLIC SUBSTRATES - DEFINITIONS, REQUIREMENTS, CHARACTERISTICS AND MARKING |
| PREN 15651-4 : DRAFT 2012 | SEALANTS FOR NON-STRUCTURAL USE IN JOINTS IN BUILDINGS AND PEDESTRIAN WALKWAYS - PART 4: SEALANTS FOR PEDESTRIAN WALKWAYS |
| 12/30266170 DC : 0 | BS EN 15534-1 - COMPOSITES MADE FROM CELLULOSE-BASED MATERIALS AND THERMOPLASTICS (USUALLY CALLED WOOD-POLYMER COMPOSITES (WPC) OR NATURAL FIBRE COMPOSITES (NFC)) - PART 1 : TEST METHODS FOR CHARACTERISATION OF COMPOUNDS AND PRODUCTS |
| BS EN 14308:2015 | Thermal insulation products for building equipment and industrial installations. Factory made rigid polyurethane foam (PUR) and polyisocyanurate foam (PIR) products. Specification |
| BS EN 438-9:2017 | High-pressure decorative laminates (HPL). Sheets based on thermosetting resins (usually called laminates) Classification and specifications for alternative core laminates |
| 17/30348262 DC : 0 | BS EN 13501-1 - FIRE CLASSIFICATION OF CONSTRUCTION PRODUCTS AND BUILDING ELEMENTS - PART 1: CLASSIFICATION USING TEST DATA FROM REACTION TO FIRE TESTS |
| 14/30314738 DC : 0 | BS EN 12004-1 - ADHESIVES FOR TILES - PART 1: REQUIREMENTS, EVALUATION OF CONFORMITY, CLASSIFICATION AND DESIGNATION |
| 08/30169537 DC : DRAFT APR 2008 | BS EN 13164 - THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE PRODUCTS OF EXTRUDED POLYSTYRENE FOAM (XPS) - SPECIFICATION |
| DIN EN 15564:2009-05 | PRECAST CONCRETE PRODUCTS - RESIN BOUND CONCRETE - REQUIREMENTS AND TEST METHODS |
| BS EN 14318-1:2013 | Thermal insulating products for buildings. In-situ formed dispensed rigid polyurethane (PUR) and polyisocyanurate (PIR) foam products Specification for the rigid foam dispensed system before installation |
| 02/106054 DC : 0 | PREN 14544 - TIMBER STRUCTURES - STRENGTH GRADED STRUCTURAL TIMBER WITH ROUND CROSS-SECTION - REQUIREMENTS |
| UNI CEN/TS 15679 : 2008 | THERMAL MODIFIED TIMBER - DEFINITIONS AND CHARACTERISTICS |
| UNE-EN 492:2013 | Fibre-cement slates and fittings - Product specification and test methods |
| UNE-EN 14307:2017 | Thermal insulation products for building equipment and industrial installations - Factory made extruded polystyrene foam (XPS) products - Specification |
| DIN EN 16240:2014-03 | LIGHT TRANSMITTING FLAT SOLID POLYCARBONATE (PC) SHEETS FOR INTERNAL AND EXTERNAL USE IN ROOFS, WALLS AND CEILINGS - REQUIREMENTS AND TEST METHODS |
| UNE-EN 15651-3:2017 | Sealants for non-structural use in joints in buildings and pedestrian walkways - Part 3: Sealants for sanitary joints |
| DIN EN 15286:2013-09 | Agglomerated stone - Slabs and tiles for wall finishes (internal and external) |
| 10/30213959 DC : 0 | BS EN 13162 - THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE MINERAL WOOL (MW) PRODUCTS - SPECIFICATION |
| 11/30238644 DC : 0 | BS EN 490 - CONCRETE ROOFING TILES AND FITTINGS FOR ROOF COVERING AND WALL CLADDING - PRODUCT SPECIFICATIONS |
| PREN 14496 : DRAFT 2016 | GYPSUM BASED ADHESIVES FOR THERMAL/ACOUSTIC INSULATION COMPOSITE PANELS AND GYPSUM BOARDS - DEFINITIONS, REQUIREMENTS AND TEST METHODS |
| 12/30254132 DC : 0 | BS EN 15651-1 - SEALANTS FOR NON-STRUCTURAL USE IN JOINTS IN BUILDINGS AND PEDESTRIAN WALKWAYS - PART 1: SEALANTS FOR FACADE ELEMENTS |
| 07/30166918 DC : DRAFT AUG 2007 | BS EN 14064-1 - THERMAL INSULATION PRODUCTS FOR BUILDINGS - IN-SITU FORMED LOOSE-FILL MINERAL WOOL (MW) PRODUCTS - PART 1: SPECIFICATION FOR THE LOOSE-FILL PRODUCTS BEFORE INSTALLATION |
| 08/30169540 DC : DRAFT APR 2008 | BS EN 13165 - THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE RIGID POLYURETHANE FOAM (PUR) PRODUCTS - SPECIFICATION |
| 15/30315084 DC : DRAFT MAY 2015 | BS EN 14309 - THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - FACTORY MADE PRODUCTS OF EXPANDED POLYSTYRENE (EPS) - SPECIFICATION |
| 07/30172345 DC : 0 | BS EN 15724 - THERMOPLASTICS STATIC TANKS FOR ABOVE GROUND STORAGE OF DOMESTIC HEATING OILS, KEROSENE AND DIESEL FUELS - SECONDARY CONTAINMENTS USED WITH TANKS COMPLYING WITH EN 13341 - REQUIREMENTS AND TEST METHODS |
| 03/119348 DC : 0 | PREN 1013-1 - LIGHT TRANSMITTING SINGLE SKIN PROFILED PLASTICS SHEETING FOR INTERNAL AND EXTERNAL ROOFING, WALL CLADDING AND CEILING FINISHES - PART 1: GENERAL REQUIREMENTS AND TEST METHODS |
| 15/30315096 DC : DRAFT MAY 2015 | BS EN 15501 - THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - FACTORY MADE EXPANDED PERLITE (EP) AND EXFOLIATED VERMICULITE (EV) PRODUCTS - SPECIFICATION |
| 05/30135869 DC : 0 | EN 15283-1 - GYPSUM BOARDS WITH FIBROUS REINFORCEMENT - DEFINITIONS, REQUIREMENTS AND TEST METHODS - PART 1: GYPSUM BOARDS WITH MAT REINFORCEMENT |
| DIN EN 15037-5:2013-08 | PRECAST CONCRETE PRODUCTS - BEAM-AND-BLOCK FLOOR SYSTEMS - PART 5: LIGHTWEIGHT BLOCKS FOR SIMPLE FORMWORK |
| 07/30152878 DC : DRAFT AUG 2007 | BS EN 14250 - TIMBER STRUCTURES - PRODUCT REQUIREMENTS FOR PREFABRICATED STRUCTURAL MEMBERS ASSEMBLED WITH PUNCHED METAL PLATE FASTENERS |
| DD CEN/TS 15679:2007 | Thermal modified timber. Definitions and characteristics |
| UNI EN 15389 : 2008 | INDUSTRIAL VALVES - PERFORMANCE CHARACTERISTICS OF THERMOPLASTIC VALVES WHEN USED AS CONSTRUCTION PRODUCTS |
| BS ISO 15791-1 : 2002 AMD 15256 | PLASTICS - DEVELOPMENT AND USE OF INTERMEDIATE-SCALE FIRE TESTS FOR PLASTICS PRODUCTS - PART 1: GENERAL GUIDANCE |
| DD ISO/TS 5658-1:2006 | Reaction to fire tests. Spread of flame Guidance on flame spread |
| PREN 15651-2 : DRAFT 2012 | SEALANTS FOR NON-STRUCTURAL USE IN JOINTS IN BUILDINGS AND PEDESTRIAN WALKWAYS - PART 2: SEALANTS FOR GLAZING |
| PREN 14308 : DRAFT 2015 | THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - FACTORY MADE RIGID POLYURETHANE FOAM (PUR) AND POLYISOCYANURATE FOAM (PIR) PRODUCTS - SPECIFICATION |
| DIN EN 124-5:2015-09 | GULLY TOPS AND MANHOLE TOPS FOR VEHICULAR AND PEDESTRIAN AREAS - PART 5: GULLY TOPS AND MANHOLE TOPS MADE OF COMPOSITE MATERIALS |
| BS EN 14307:2015 | Thermal insulation products for building equipment and industrial installations. Factory made extruded polystyrene foam (XPS) products. Specification |
| UNE-EN 14308:2017 | Thermal insulation products for building equipment and industrial installations - Factory made rigid polyurethane foam (PUR) and polyisocyanurate foam (PIR) products - Specification |
| 17/30355245 DC : 0 | BS ISO 4586-6 - HIGH-PRESSURE DECORATIVE LAMINATES (HPL, HPDL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 6: CLASSIFICATION AND SPECIFICATIONS FOR EXTERIOR-GRADE COMPACT LAMINATES OF THICKNESS 2 MM AND GREATER |
| UNE-EN 15814:2011 | Polymer modified bituminous thick coatings for waterproofing - Definitions and requirements |
| PREN 15101-1 : DRAFT 2013 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - IN-SITU FORMED LOOSE FILL CELLULOSE (LFCI) PRODUCTS - PART 1: SPECIFICATION FOR THE PRODUCTS BEFORE INSTALLATION |
| UNE-EN 15715:2012 | Thermal insulation products - Instructions for mounting and fixing for reaction to fire testing - Factory made products |
| BS EN 14305:2015 | Thermal insulation products for building equipment and industrial installations. Factory made cellular glass (CG) products. Specification |
| UNI EN 15286 : 2013 | AGGLOMERATED STONE - SLABS AND TILES FOR WALL FINISHES (INTERNAL AND EXTERNAL) |
| I.S. EN ISO 25762:2012 | PLASTICS - GUIDANCE ON THE ASSESSMENT OF THE FIRE CHARACTERISTICS AND FIRE PERFORMANCE OF FIBRE-REINFORCED POLYMER COMPOSITES (ISO 25762:2009) |
| I.S. EN 13245-2:2008 | PLASTICS - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) PROFILES FOR BUILDING APPLICATIONS - PART 2: PVC-U PROFILES AND PVC-UE PROFILES FOR INTERNAL AND EXTERNAL WALL AND CEILING FINISHES |
| BS EN 14309:2015 | Thermal insulation products for building equipment and industrial installations. Factory made products of expanded polystyrene (EPS). Specification |
| PREN 15102 : DRAFT 2016 | DECORATIVE WALLCOVERINGS - ROLL FORM |
| I.S. EN 15037-5:2013 | PRECAST CONCRETE PRODUCTS - BEAM-AND-BLOCK FLOOR SYSTEMS - PART 5: LIGHTWEIGHT BLOCKS FOR SIMPLE FORMWORK |
| PRCEN/TS 115-4 : DRAFT 2015 | SAFETY OF ESCALATORS AND MOVING WALKS - PART 4: INTERPRETATIONS RELATED TO EN 115 FAMILY OF STANDARDS |
| I.S. EN 60695-8-1:2017 | FIRE HAZARD TESTING - PART 8-1: HEAT RELEASE - GENERAL GUIDANCE |
| I.S. EN 15286:2013 | AGGLOMERATED STONE - SLABS AND TILES FOR WALL FINISHES (INTERNAL AND EXTERNAL) |
| I.S. EN 1013:2012 | LIGHT TRANSMITTING SINGLE SKIN PROFILED PLASTICS SHEETS FOR INTERNAL AND EXTERNAL ROOFS, WALLS AND CEILINGS - REQUIREMENTS AND TEST METHODS |
| UNE-EN 12467:2013 | Fibre-cement flat sheets - Product specification and test methods |
| PREN 12050-1 : DRAFT 2012 | WASTEWATER LIFTING PLANTS FOR BUILDINGS AND SITES - PART 1: LIFTING PLANTS FOR WASTEWATER CONTAINING FAECAL MATTER |
| I.S. EN 14306:2015 | THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - FACTORY MADE CALCIUM SILICATE (CS) PRODUCTS - SPECIFICATION |
| ISO 10840:2008 | Plastics — Guidance for the use of standard fire tests |
| DIN EN 15102:2016-02 (Draft) | DECORATIVE WALL COVERINGS - ROLL AND PANEL FORM |
| 15/30324901 DC : 0 | BS EN 1504-3 - PRODUCTS AND SYSTEMS FOR THE PROTECTION AND REPAIR OF CONCRETE STRUCTURES - DEFINITIONS, REQUIREMENTS, QUALITY CONTROL AND AVCP - PART 3: REPAIR CONCRETE AND MORTARS |
| UNI EN 15102 : 2011 | DECORATIVE WALL COVERINGS - ROLL AND PANEL FORM |
| 14/30297462 DC : 0 | BS EN 15015 - PLASTICS PIPING SYSTEMS - HOT AND COLD WATER PIPING COMPONENTS - REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR PIPES AND FITTINGS |
| 15/30316975 DC : 0 | BS EN 1504-2 - PRODUCTS AND SYSTEMS FOR THE PROTECTION AND REPAIR OF CONCRETE STRUCTURES - DEFINITIONS, REQUIREMENTS, QUALITY CONTROL AND EVALUATION OF CONFORMITY - PART 2: SURFACE PROTECTION SYSTEMS FOR CONCRETE |
| I.S. EN 16724:2015 | THERMAL INSULATION PRODUCTS FOR BUILDING APPLICATIONS - INSTRUCTIONS FOR MOUNTING AND FIXING FOR DETERMINATION OF THE REACTION TO FIRE TESTING OF EXTERNAL THERMAL INSULATION COMPOSITE SYSTEMS (ETICS) |
| 14/30297459 DC : 0 | BS EN 15012 - PLASTICS PIPING SYSTEMS - BURIED AND ABOVE GROUND PIPING COMPONENTS FOR NON PRESSURE SOIL AND WASTE DISCHARGE WITHIN THE BUILDING STRUCTURE - REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR PIPES AND FITTINGS |
| PREN 1794-3 : DRAFT 2014 | ROAD TRAFFIC NOISE REDUCING DEVICES - NON-ACOUSTIC PERFORMANCE - PART 3: REACTION TO FIRE - BURNING BEHAVIOUR OF NOISE REDUCING DEVICES AND CLASSIFICATION |
| PREN 16491 : DRAFT 2012 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE COMPOSITE PRODUCTS - SPECIFICATION |
| I.S. EN 14308:2015 | THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - FACTORY MADE RIGID POLYURETHANE FOAM (PUR) AND POLYISOCYANURATE FOAM (PIR) PRODUCTS - SPECIFICATION |
| ISO 4586-6:2015 | High-pressure decorative laminates (HPL, HPDL) Sheets based on thermosetting resins (Usually called Laminates) Part 6: Classification and specifications for exterior-grade compact laminates of thickness 2 mm and greater |
| ISO 29903:2012 | Guidance for comparison of toxic gas data between different physical fire models and scales |
| EN 492:2012+A2:2018 | Fibre-cement slates and fittings - Product specification and test methods |
| I.S. EN 15389:2008 | INDUSTRIAL VALVES - PERFORMANCE CHARACTERISTICS OF THERMOPLASTIC VALVES WHEN USED AS CONSTRUCTION PRODUCTS |
| ISO 4586-4:2015 | High-pressure decorative laminates (HPL, HPDL) Sheets based on thermosetting resins (Usually called Laminates) Part 4: Classification and specifications for compact laminates of thickness 2 mm and greater |
| ISO 4586-8:2015 | High-pressure decorative laminates (HPL, HPDL) Sheets based on thermosetting resins (Usually called Laminates) Part 8: Classification and specifications for alternative core laminates |
| I.S. EN 14313:2015 | THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - FACTORY MADE POLYETHYLENE FOAM (PEF) PRODUCTS - SPECIFICATION |
| I.S. EN 15012:2007 | PLASTICS PIPING SYSTEMS - SOIL AND WASTE DISCHARGE SYSTEMS WITHIN THE BUILDING STRUCTURE - PERFORMANCE CHARACTERISTICS FOR PIPES, FITTINGS AND THEIR JOINTS |
| I.S. EN 15564:2008 | PRECAST CONCRETE PRODUCTS - RESIN BOUND CONCRETE - REQUIREMENTS AND TEST METHODS |
| I.S. EN 15102:2007 | DECORATIVE WALL COVERINGS - ROLL AND PANEL FORM |
| S.R. CEN TS 15534-3:2007 | WOOD-PLASTICS COMPOSITES (WPC) - PART 3: CHARACTERISATION OF WPC PRODUCTS |
| ISO 4586-7:2015 | High-pressure decorative laminates (HPL, HPDL) Sheets based on thermosetting resins (Usually called Laminates) Part 7: Classification and specifications for design laminates |
| I.S. CEN/TS 15447:2006 | MOUNTING AND FIXING IN REACTION TO FIRE TESTS UNDER THE CONSTRUCTION PRODUCTS DIRECTIVE |
| DIN EN 14209:2016-02 (Draft) | PREFORMED PLASTERBOARD CORNICES - DEFINITIONS, REQUIREMENTS AND TEST METHODS |
| DIN EN 14190:2014-09 | Gypsum board products from reprocessing - Definitions, requirements and test methods |
| DIN EN 12050-2:2015-05 | WASTEWATER LIFTING PLANTS FOR BUILDINGS AND SITES - PART 2: LIFTING PLANTS FOR FAECAL-FREE WASTEWATER |
| DIN EN 14080:2013-09 | TIMBER STRUCTURES - GLUED LAMINATED TIMBER AND GLUED SOLID TIMBER - REQUIREMENTS |
| DIN EN 438-6:2016-06 | HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 6: CLASSIFICATION AND SPECIFICATIONS FOR EXTERIOR-GRADE COMPACT LAMINATES OF THICKNESS 2 MM AND GREATER |
| DIN EN 14081-1:2016-06 | TIMBER STRUCTURES - STRENGTH GRADED STRUCTURAL TIMBER WITH RECTANGULAR CROSS SECTION - PART 1: GENERAL REQUIREMENTS |
| BS EN 12050-1:2015 | Wastewater lifting plants for buildings and sites Lifting plants for wastewater containing faecal matter |
| BS EN 13950:2014 | Gypsum board thermal/acoustic insulation composite panels. Definitions, requirements and test methods |
| BS EN 13915:2017 | Prefabricated gypsum plasterboard panels with a cellular paperboard core. Definitions, requirements and test methods |
| BS EN 13167 : 2012 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE CELLULAR GLASS (CG) PRODUCTS - SPECIFICATION |
| UNE-EN 494:2013 | Fibre-cement profiled sheets and fittings - Product specification and test methods |
| BS EN 14209:2017 | Preformed plasterboard cornices. Definitions, requirements and test methods |
| BS EN 12004 : 2007 | ADHESIVES FOR TILES - REQUIREMENTS, EVALUATION OF CONFORMITY, CLASSIFICATION AND DESIGNATION |
| BS EN 438-6:2016 | High-pressure decorative laminates (HPL). Sheets based on thermosetting resins (usually called laminates) Classification and specifications for Exterior-grade compact laminates of thickness 2 mm and greater |
| BS EN 13171 : 2012 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE WOOD FIBRE (WF) PRODUCTS - SPECIFICATION |
| BS EN 13963:2014 | Jointing materials for gypsum boards. Definitions, requirements and test methods |
| UNE-EN 13963:2014 | Jointing materials for gypsum boards - Definitions, requirements and test methods |
| BS EN 13165 : 2012 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE RIGID POLYURETHANE FOAM (PU) PRODUCTS - SPECIFICATION |
| UNE-EN 13166:2013 | Thermal insulation products for buildings - Factory made phenolic foam (PF) products - Specification |
| BS EN 14474:2004 | Precast concrete products. Concrete with wood-chips as aggregate. Requirements and test methods |
| BS EN 438-4:2016 | High-pressure decorative laminates (HPL). Sheets based on thermosetting resins (usually called laminates) Classification and specifications for compact laminates of thickness 2 mm and greater |
| 15/30324856 DC : 0 | BS EN 115-1 - SAFETY OF ESCALATORS AND MOVING WALKS - PART 1: CONSTRUCTION AND INSTALLATION |
| UNE-EN 13167:2013 | Thermal insulation products for buildings - Factory made cellular glass (CG) products - Specification |
| BS EN 12050-4:2015 | Wastewater lifting plants for buildings and sites Non-return valves for faecal-free wastewater and wastewater containing faecal matter |
| UNE-EN 16351:2016 | Timber structures - Cross laminated timber - Requirements |
| BS EN 60695-8-2:2017 | Fire hazard testing Heat release. Summary and relevance of test methods |
| UNE-EN 13164:2013 | Thermal insulation products for buildings - Factory made extruded polystyrene foam (XPS) products - Specification |
| BS EN 13166 : 2012 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE PHENOLIC FOAM (PF) PRODUCTS - SPECIFICATION |
| 09/30193524 DC : 0 | BS EN 62222 - FIRE PERFORMANCE OF COMMUNICATION CABLES INSTALLED IN BUILDINGS - METHODS OF FIRE RETARDANCY |
| BS EN 15102 : 2007 | DECORATIVE WALL COVERINGS - ROLL AND PANEL FORM |
| UNE-EN 13169:2013 | Thermal insulation products for buildings - Factory made expanded perlite board (EPB) products - Specification |
| UNE-EN 14081-1:2016 | Timber structures - Strength graded structural timber with rectangular cross section - Part 1: General requirements |
| UNE-EN ISO 15791-1:2014 | Plastics - Development and use of intermediate-scale fire tests for plastics products - Part 1: General guidance (ISO 15791-1:2014) |
| IEC 60695-6-1:2005+AMD1:2010 CSV | Fire hazard testing - Part 6-1: Smoke obscuration - General guidance |
| UNE-EN 14190:2014 | Gypsum board products from reprocessing - Definitions, requirements and test methods |
| BS EN 14783:2013 | Fully supported metal sheet and strip for roofing, external cladding and internal lining. Product specification and requirements |
| DIN EN 14783:2013-07 | FULLY SUPPORTED METAL SHEET AND STRIP FOR ROOFING, EXTERNAL CLADDING AND INTERNAL LINING - PRODUCT SPECIFICATION AND REQUIREMENTS |
| BS EN 13162 : 2012 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE MINERAL WOOL (MW) PRODUCTS - SPECIFICATION |
| BS EN 14351-1 : 2006 | WINDOWS AND DOORS - PRODUCT STANDARD, PERFORMANCE CHARACTERISTICS - PART 1: WINDOWS AND EXTERNAL PEDESTRIAN DOORSETS |
| UNE-EN 13162:2013 | Thermal insulation products for buildings - Factory made mineral wool (MW) products - Specification |
| UNE-EN 13165:2013 | Thermal insulation products for buildings - Factory made rigid polyurethane foam (PU) products - Specification |
| BS EN 14250:2010 | Timber structures. Product requirements for prefabricated structural members assembled with punched metal plate fasteners |
| UNE-EN 1013:2013 | Light transmitting single skin profiled plastics sheets for internal and external roofs, walls and ceilings - Requirements and test methods |
| IEC TR 62222:2012 | Fire performance of communication cables installed in buildings |
| UNE-EN 13171:2013 | Thermal insulation products for buildings - Factory made wood fibre (WF) products - Specification |
| UNE-EN 1873:2015 | Prefabricated accessories for roofing - Individual rooflights of plastics - Product specification and test methods |
| BS EN 14246:2006 | Gypsum elements for suspended ceilings. Definitions, requirements and test methods |
| IEC 60695-1-10:2016 | Fire hazard testing - Part 1-10: Guidance for assessing the fire hazard of electrotechnical products - General guidelines |
| BS EN 13830:2015 | Curtain walling. Product standard |
| UNE-EN 520:2005 | Gypsum plasterboards - Definitions, requirements and test methods |
| UNE-EN 13163:2013 | Thermal insulation products for buildings - Factory made expanded polystyrene (EPS) products - Specification |
| BS EN 14080:2013 | Timber structures. Glued laminated timber and glued solid timber. Requirements |
| UNE-EN 12050-1:2015 | Wastewater lifting plants for buildings and sites - Part 1: Lifting plants for wastewater containing faecal matter |
| UNE-EN 16069:2013 | Thermal insulation products for buildings - Factory made products of polyethylene foam (PEF) - Specification |
| UNE-EN 13170:2013 | Thermal insulation products for buildings - Factory made products of expanded cork (ICB) - Specification |
| BS EN 13500:2003 | Thermal insulation products for buildings. External thermal insulation composite systems (ETICS) based on mineral wool. Specification |
| UNE-EN 13168:2013 | Thermal insulation products for buildings - Factory made wood wool (WW) products - Specification |
| ISO 15791-1:2014 | Plastics — Development and use of intermediate-scale fire tests for plastics products — Part 1: General guidance |
| BS EN 438-3:2016 | High-pressure decorative laminates (HPL). Sheets based on thermosetting resins (usually called laminates) Classification and specifications for laminates less than 2 mm thick intended for bonding to supporting substrates |
| ISO 25762:2009 | Plastics Guidance on the assessment of the fire characteristics and fire performance of fibre-reinforced polymer composites |
| UNE-EN 438-6:2016 | High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (Usually called Laminates) - Part 6: Classification and specifications for Exterior-grade compact laminates of thickness 2 mm and greater |
| UNE-EN 14209:2017 | Preformed plasterboard cornices - Definitions, requirements and test methods |
| UNE-EN 12050-2:2015 | Wastewater lifting plants for buildings and sites - Part 2: Lifting plants for faecal-free wastewater |
| BS EN 14800:2007 | Corrugated safety metal hose assemblies for the connection of domestic appliances using gaseous fuels |
| EN 14190:2014 | Gypsum board products from reprocessing - Definitions, requirements and test methods |
| EN 14308:2015 | Thermal insulation products for building equipment and industrial installations - Factory made rigid polyurethane foam (PUR) and polyisocyanurate foam (PIR) products - Specification |
| EN 15651-2:2017 | Sealants for non-structural use in joints in buildings and pedestrian walkways - Part 2: Sealants for glazing |
| EN 15286:2013 | Agglomerated stone - Slabs and tiles for wall finishes (internal and external) |
| EN 15423:2008 | Ventilation for buildings - Fire precautions for air distribution systems in buildings |
| EN 15266:2007 | Stainless steel pliable corrugated tubing kits in buildings for gas with an operating pressure up to 0,5 bar |
| EN 13950:2014 | Gypsum board thermal/acoustic insulation composite panels - Definitions, requirements and test methods |
| EN 14306:2015 | Thermal insulation products for building equipment and industrial installations - Factory made calcium silicate (CS) products - Specification |
| EN 14319-1:2013 | Thermal insulating products for building equipment and industrial installations - In-situ formed dispensed rigid polyurethane (PUR) and polyisocyanurate foam (PIR) products - Part 1: Specification for the rigid foam dispensed system before installation |
| EN 1794-3:2016 | Road traffic noise reducing devices - Non-acoustic performance - Part 3: Reaction to fire - Burning behaviour of noise reducing devices and classification |
| EN 15283-2:2008+A1:2009 | Gypsum boards with fibrous reinforcement - Definitions, requirements and test methods - Part 2: Gypsum fibre boards |
| EN 14305:2015 | Thermal insulation products for building equipment and industrial installations - Factory made cellular glass (CG) products - Specification |
| EN 13168:2012+A1:2015 | Thermal insulation products for buildings - Factory made wood wool (WW) products - Specification |
| EN 14471:2013+A1:2015 | Chimneys - System chimneys with plastic flue liners - Requirements and test methods |
| EN 14080:2013 | Timber structures - Glued laminated timber and glued solid timber - Requirements |
| EN 13859-1:2014 | Flexible sheets for waterproofing - Definitions and characteristics of underlays - Part 1: Underlays for discontinuous roofing |
| EN 16153:2013+A1:2015 | Light transmitting flat multiwall polycarbonate (PC) sheets for internal and external use in roofs, walls and ceilings - Requirements and test methods |
| EN 13859-2:2014 | Flexible sheets for waterproofing - Definitions and characteristics of underlays - Part 2: Underlays for walls |
| EN 14307:2015 | Thermal insulation products for building equipment and industrial installations - Factory made extruded polystyrene foam (XPS) products - Specification |
| EN 438-6:2016 | High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (usually called laminates) - Part 6: Classification and specifications for Exterior-grade compact laminates of thickness 2 mm and greater |
| EN 520:2004+A1:2009 | Gypsum plasterboards - Definitions, requirements and test methods |
| EN 13164:2012+A1:2015 | Thermal insulation products for buildings - Factory made extruded polystyrene foam (XPS) products - Specification |
| EN 438-4:2016 | High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (usually called laminates) - Part 4: Classification and specifications for compact laminates of thickness 2 mm and greater |
| EN 15814:2011+A2:2014 | Polymer modified bituminous thick coatings for waterproofing - Definitions and requirements |
| EN 15012:2007 | Plastics piping systems - Soil and waste discharge systems within the building structure - Performance characteristics for pipes, fittings and their joints |
| EN 14509:2013 | Self-supporting double skin metal faced insulating panels - Factory made products - Specifications |
| EN 16069:2012+A1:2015 | Thermal insulation products for buildings - Factory made products of polyethylene foam (PEF) - Specification |
| EN 14309:2015 | Thermal insulation products for building equipment and industrial installations - Factory made products of expanded polystyrene (EPS) - Specification |
| EN 13171:2012+A1:2015 | Thermal insulation products for buildings - Factory made wood fibre (WF) products - Specification |
| ONORM EN 877 : 2008 | CAST IRON PIPES AND FITTINGS, THEIR JOINTS AND ACCESSORIES FOR THE EVACUATION OF WATER FROM BUILDINGS - REQUIREMENTS, TEST METHODS AND QUALITY ASSURANCE |
| EN 14351-1:2006+A2:2016 | Windows and doors - Product standard, performance characteristics - Part 1: Windows and external pedestrian doorsets |
| EN 14474:2004 | Precast concrete products - Concrete with wood-chips as aggregate - Requirements and test methods |
| EN 13963:2014 | Jointing materials for gypsum boards - Definitions, requirements and test methods |
| EN 14081-1:2016 | Timber structures - Strength graded structural timber with rectangular cross section - Part 1: General requirements |
| EN 15389:2008 | Industrial valves - Performance characteristics of thermoplastic valves when used as construction products |
| EN 13915:2017 | Prefabricated gypsum plasterboard panels with a cellular paperboard core - Definitions, requirements and test methods |
| EN 15619:2014 | Rubber or plastic coated fabrics - Safety of temporary structures (tents) - Specification for coated fabrics intended for tents and related structures |
| EN 14209:2017 | Preformed plasterboard cornices - Definitions, requirements and test methods |
| EN 16623:2015 | Paints and varnishes - Reactive coatings for fire protection of metallic substrates - Definitions, requirements, characteristics and marking |
| EN 14716:2004 | Stretched ceilings - Requirements and test methods |
| EN 14320-1:2013 | Thermal insulating products for building equipment and industrial installations - In-situ formed sprayed rigid polyurethane (PUR) and polyisocyanurate foam (PIR) products - Part 1: Specification for the rigid foam spray system before installation |
| EN 1873:2014+A1:2016 | Prefabricated accessories for roofing - Individual rooflights of plastics - Product specification and test methods |
| EN 15651-3:2017 | Sealants for non-structural use in joints in buildings and pedestrian walkways - Part 3: Sealants for sanitary joints |
| EN 15037-5:2013 | Precast concrete products - Beam-and-block floor systems - Part 5: Lightweight blocks for simple formwork |
| EN 14304:2015 | Thermal insulation products for building equipment and industrial installations - Factory made flexible elastomeric foam (FEF) products - Specification |
| EN 14934:2007 | Thermal insulation and light weight fill products for civil engineering applications - Factory made products of extruded polystyrene foam (XPS) - Specification |
| EN 438-7:2005 | High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (Usually called Laminates) - Part 7: Compact laminate and HPL composite panels for internal and external wall and ceiling finishes |
| EN 14496:2017 | Gypsum based adhesives for thermal/acoustic insulation composite panels and gypsum boards - Definitions, requirements and test methods |
| EN 16724:2015 | Thermal insulation products for building applications - Instructions for mounting and fixing for determination of the reaction to fire testing of external thermal Insulation composite systems (ETICS) |
| EN 15497:2014 | Structural finger jointed solid timber - Performance requirements and minimum production requirements |
| EN ISO 25762:2012 | Plastics - Guidance on the assessment of the fire characteristics and fire performance of fibre-reinforced polymer composites (ISO 25762:2009) |
| EN 14782:2006 | Self-supporting metal sheet for roofing, external cladding and internal lining - Product specification and requirements |
| EN 16000:2010 | Plastics piping systems - Systems within the building structure - Mounting and fixing of components in the test apparatus to thermal attack by a single burning item |
| EN 15228:2009 | Structural timber - Structural timber preservative treated against biological attack |
| EN 14315-1:2013 | Thermal insulating products for buildings - In-situ formed sprayed rigid polyurethane (PUR) and polyisocyanurate (PIR) foam products - Part 1: Specification for the rigid foam spray system before installation |
| EN 494:2012+A1:2015 | Fibre-cement profiled sheets and fittings - Product specification and test methods |
| EN 14303:2015 | Thermal insulation products for building equipment and industrial installations - Factory made mineral wool (MW) products - Specification |
| EN 15715:2009 | Thermal insulation products - Instructions for mounting and fixing for reaction to fire testing - Factory made products |
| EN 15701:2016 | Plastics - Thermoplastic jackets for insulation products for building equipment and industrial installations - Requirements and test methods |
| EN 14314:2015 | Thermal insulation products for building equipment and industrial installations - Factory made phenolic foam (PF) products - Specification |
| EN 14933:2007 | Thermal insulation and light weight fill products for civil engineering applications - Factory made products of expanded polystyrene (EPS) - Specification |
| EN 14800:2007 | Corrugated safety metal hose assemblies for the connection of domestic appliances using gaseous fuels |
| EN 15564:2008 | Precast concrete products - Resin bound concrete - Requirements and test methods |
| EN 15501:2015 | Thermal insulation products for building equipment and industrial installations - Factory made expanded perlite (EP) and exfoliated vermiculite (EV) products - Specification |
| EN 491:2011 | Concrete roofing tiles and fittings for roof covering and wall cladding - Test methods |
| EN 14318-1:2013 | Thermal insulating products for buildings - In-situ formed dispensed rigid polyurethane (PUR) and polyisocyanurate (PIR) foam products - Part 1: Specification for the rigid foam dispensed system before installation |
| EN 14313:2015 | Thermal insulation products for building equipment and industrial installations - Factory made polyethylene foam (PEF) products - Specification |
| EN 14783:2013 | Fully supported metal sheet and strip for roofing, external cladding and internal lining - Product specification and requirements |
| EN 16025-1:2013 | Thermal and/or sound insulating products in building construction - Bound EPS ballastings - Part 1: Requirements for factory premixed EPS dry plaster |
| EN 15651-1:2017 | Sealants for non-structural use in joints in buildings and pedestrian walkways - Part 1: Sealants for facade elements |
| EN 438-3:2016 | High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (usually called laminates) - Part 3: Classification and specifications for laminates less than 2 mm thick intended for bonding to supporting substrates |
| I.S. EN 16755:2017 | DURABILITY OF REACTION TO FIRE PERFORMANCE - CLASSES OF FIRE-RETARDANT TREATED WOOD PRODUCTS IN INTERIOR AND EXTERIOR END USE APPLICATIONS |
| 14/30300561 DC : 0 | BS EN 16755 - DURABILITY OF REACTION TO FIRE PERFORMANCE - CLASSES OF FIRERETARDANT TREATED WOOD PRODUCTS IN INTERIOR AND EXTERIOR END USE APPLICATIONS |
| BS EN 15283-1 : 2008 | GYPSUM BOARDS WITH FIBROUS REINFORCEMENT - DEFINITIONS, REQUIREMENTS AND TEST METHODS - PART 1: GYPSUM BOARDS WITH MAT REINFORCEMENT |
| PREN 438-4 : DRAFT 2014 | HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 4: CLASSIFICATION AND SPECIFICATIONS FOR COMPACT LAMINATES OF THICKNESS 2 MM AND GREATER |
| PREN 14716 : DRAFT 2014 | STRETCHED CEILINGS - REQUIREMENTS AND TEST METHODS |
| PREN 12050-3 : DRAFT 2012 | WASTEWATER LIFTING PLANTS FOR BUILDINGS AND SITES - PART 3: LIFTING PLANTS FOR LIMITED APPLICATIONS |
| BS EN 14319-1:2013 | Thermal insulating products for building equipment and industrial installations. In-situ formed dispensed rigid polyurethane (PUR) and polyisocyanurate foam (PIR) products Specification for the rigid foam dispensed system before installation |
| BS EN 60695-8-1:2017 | Fire hazard testing Heat release. General guidance |
| DIN EN 14318-1:2013-04 | THERMAL INSULATING PRODUCTS FOR BUILDINGS - IN-SITU FORMED DISPENSED RIGID POLYURETHANE (PUR) AND POLYISOCYANURATE (PIR) FOAM PRODUCTS - PART 1: SPECIFICATION FOR THE RIGID FOAM DISPENSED SYSTEM BEFORE INSTALLATION |
| PREN 13501-1 : DRAFT 2017 | FIRE CLASSIFICATION OF CONSTRUCTION PRODUCTS AND BUILDING ELEMENTS - PART 1: CLASSIFICATION USING TEST DATA FROM REACTION TO FIRE TESTS |
| UNE-EN 1794-3:2016 | Road traffic noise reducing devices - Non-acoustic performance - Part 3: Reaction to fire - Burning behaviour of noise reducing devices and classification |
| PREN 15651-1 : DRAFT 2012 | SEALANTS FOR NON-STRUCTURAL USE IN JOINTS IN BUILDINGS AND PEDESTRIAN WALKWAYS - PART 1: SEALANTS FOR FACADE ELEMENTS |
| BS EN 1794-3:2016 | Road traffic noise reducing devices. Non-acoustic performance Reaction to fire. Burning behaviour of noise reducing devices and classification |
| 05/30135872 DC : 0 | EN 15283-2 - GYPSUM BOARDS WITH FIBROUS REINFORCEMENT - DEFINITIONS, REQUIREMENTS AND TEST METHODS - PART 2: GYPSUM FIBRE BOARDS |
| I.S. EN 438-7:2005 | HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 7: COMPACT LAMINATE AND HPL COMPOSITE PANELS FOR INTERNAL AND EXTERNAL WALL AND CEILING FINISHES |
| UNE-EN 15497:2014 | Structural finger jointed solid timber - Performance requirements and minimum production requirements |
| I.S. EN 16623:2015 | PAINTS AND VARNISHES - REACTIVE COATINGS FOR FIRE PROTECTION OF METALLIC SUBSTRATES - DEFINITIONS, REQUIREMENTS, CHARACTERISTICS AND MARKING |
| 06/30133753 DC : DRAFT MAY 2006 | ISO 24473 - FIRE TESTS - OPEN CALORIMETRY - MEASUREMENT OF THE RATE OF PRODUCTION OF HEAT AND COMBUSTION PRODUCTS FOR FIRES OF UP TO 20MW |
| DD CEN/TS 15447:2006 | Mounting and fixing in reaction to fire tests under the Construction Products Directive |
| 11/30239900 DC : DRAFT MAR 2011 | BS EN 15012 - PLASTICS PIPING SYSTEMS - NON PRESSURE SOIL AND WASTE DISCHARGE PIPING COMPONENTS WITHIN THE BUILDING STRUCTURE - REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR PIPES AND FITTINGS |
| PREN 438-8 : DRAFT 2017 | HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 8: CLASSIFICATION AND SPECIFICATIONS FOR DESIGN LAMINATES |
| BS EN 15715:2009 | Thermal insulation products. Instructions for mounting and fixing for reaction to fire testing. Factory made products |
| 10/30213968 DC : 0 | BS EN 13165 - THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE RIGID POLYURETHANE FOAM (PU) PRODUCTS - SPECIFICATION |
| 08/30194543 DC : 0 | BS ISO 2219 - THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY-MADE PRODUCTS OF EXPANDED CORK (ICB) - SPECIFICATION |
| 12/30211334 DC : 0 | BS ISO 15791-1 - PLASTICS - DEVELOPMENT AND USE OF INTERMEDIATE-SCALE FIRE TESTS FOR PLASTICS PRODUCTS - PART 1: GENERAL GUIDANCE (ISO/DIS 15791-1:2012) |
| BS EN 15283-2 : 2008 | GYPSUM BOARDS WITH FIBROUS REINFORCEMENT - DEFINITIONS, REQUIREMENTS AND TEST METHODS - PART 2: GYPSUM FIBRE BOARDS |
| 08/30154274 DC : DRAFT MAR 2008 | BS ISO 25762 - PLASTICS - GUIDANCE ON THE ASSESSMENT OF FIRE CHARACTERISTICS AND FIRE PERFORMANCE OF FIBRE-REINFORCED COMPOSITES |
| PREN 491 : DRAFT 2011 | CONCRETE ROOFING TILES AND FITTINGS FOR ROOF COVERING AND WALL CLADDING - TEST METHODS |
| 05/30111233 DC : 0 | BS EN 13245-2 - PLASTICS - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) PROFILES FOR BUILDING APPLICATIONS - PART 2: PROFILES FOR INTERNAL AND EXTERNAL WALL AND CEILING FINISHES |
| 14/30295274 DC : 0 | BS EN 1794-3 - ROAD TRAFFIC NOISE REDUCING DEVICES - NON-ACOUSTIC PERFORMANCE - PART 3: REACTION TO FIRE - BURNING BEHAVIOUR OF NOISE REDUCING DEVICES AND CLASSIFICATION |
| DIN EN 15423:2008-09 | VENTILATION FOR BUILDINGS - FIRE PRECAUTIONS FOR AIR DISTRIBUTION SYSTEMS IN BUILDINGS |
| DIN EN 14319-1:2013-04 | Thermal insulating products for building equipment and industrial installations - In-situ formed dispensed rigid polyurethane (PUR) and polyisocyanurate (PIR) foam products - Part 1: Specification for the rigid foam dispensed system before installation |
| 05/30136538 DC : 0 | PREN 14307 - THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - FACTORY MADE EXTRUDED POLYSTYRENE FOAM (XPS) PRODUCTS - SPECIFICATION |
| 11/30251985 DC : 0 | BS EN 13950 - GYPSUM PLASTERBOARD THERMAL/ACOUSTIC INSULATION COMPOSITE PANELS - DEFINITIONS, REQUIREMENTS AND TEST METHODS |
| 16/30340635 DC : 0 | BS EN 438-9 - HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 9: CLASSIFICATION AND SPECIFICATIONS FOR ALTERNATIVE CORE LAMINATES |
| DIN EN 15619:2014-07 | RUBBER OR PLASTIC COATED FABRICS - SAFETY OF TEMPORARY STRUCTURES (TENTS) - SPECIFICATION FOR COATED FABRICS INTENDED FOR TENTS AND RELATED STRUCTURES |
| UNE-EN 16025-1:2016 | Thermal and/or sound insulating products in building construction - Bound EPS ballastings - Part 1: Requirements for factory premixed EPS dry plaster |
| BS EN 14303 : 2009 | THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - FACTORY MADE MINERAL WOOL (MW) PRODUCTS - SPECIFICATION |
| UNE-EN 14319-1:2013 | Thermal insulating products for building equipment and industrial installations - In-situ formed dispensed rigid polyurethane (PUR) and polyisocyanurate foam (PIR) products - Part 1: Specification for the rigid foam dispensed system before installation |
| BS EN 14315-1:2013 | Thermal insulating products for buildings. In-situ formed sprayed rigid polyurethane (PUR) and polyisocyanurate (PIR) foam products Specification for the rigid foam spray system before installation |
| DIN EN 15497 E : 2014 | STRUCTURAL FINGER JOINTED SOLID TIMBER - PERFORMANCE REQUIREMENTS AND MINIMUM PRODUCTION REQUIREMENTS |
| BS EN 124-6:2015 | Gully tops and manhole tops for vehicular and pedestrian areas Gully tops and manhole tops made of polypropylene (PP), polyethylene (PE) or unplasticized poly(vinyl chloride) (PVC-U) |
| 07/30169818 DC : 0 | BS EN 1013 - LIGHT TRANSMITTING SINGLE SKIN PROFILED PLASTICS SHEETS FOR INTERNAL AND EXTERNAL ROOFS, WALLS AND CEILINGS - REQUIREMENTS AND TEST METHODS |
| 15/30315093 DC : DRAFT MAY 2015 | BS EN 14303 - THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - FACTORY MADE MINERAL WOOL (MW) PRODUCTS - SPECIFICATION |
| 14/30303788 DC : 0 | BS EN 438-3 - HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 3: CLASSIFICATION AND SPECIFICATIONS FOR LAMINATES LESS THAN 2 MM THICK INTENDED FOR BONDING TO SUPPORTING SUBSTRATES |
| 12/30254138 DC : 0 | BS EN 15651-3 - SEALANTS FOR NON-STRUCTURAL USE IN JOINTS IN BUILDINGS AND PEDESTRIAN WALKWAYS - PART 3: SEALANTS FOR SANITARY JOINTS |
| 12/30265295 DC : 0 | BS EN 12050-3 - WASTEWATER LIFTING PLANTS FOR BUILDINGS AND SITES - PRINCIPLES OF CONSTRUCTION AND TESTING - PART 3: LIFTING PLANTS FOR LIMITED APPLICATIONS |
| I.S. EN 14319-1:2013 | THERMAL INSULATING PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - IN-SITU FORMED DISPENSED RIGID POLYURETHANE (PUR) AND POLYISOCYANURATE FOAM (PIR) PRODUCTS - PART 1: SPECIFICATION FOR THE RIGID FOAM DISPENSED SYSTEM BEFORE INSTALLATION |
| DIN EN 15389:2008-10 | INDUSTRIAL VALVES - PERFORMANCE CHARACTERISTICS OF THERMOPLASTIC VALVES WHEN USED AS CONSTRUCTION PRODUCTS |
| 10/30213989 DC : 0 | BS EN 16069 - THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE PRODUCTS OF POLYETHYLENE FOAM (PEF) - SPECIFICATION |
| DIN EN 15814:2015-03 | POLYMER MODIFIED BITUMINOUS THICK COATINGS FOR WATERPROOFING - DEFINITIONS AND REQUIREMENTS |
| PD CEN/TR 14819-1:2004 | Safety recommendations for cableway installations designed to carry persons. Prevention and fight against fire Funicular railways in tunnels |
| BS EN 15012 : 2008 | PLASTICS PIPING SYSTEMS - SOIL AND WASTE DISCHARGE SYSTEMS WITHIN THE BUILDING STRUCTURE - PERFORMANCE CHARACTERISTICS FOR PIPES, FITTINGS AND THEIR JOINTS |
| DD CEN/TS 15534-3:2007 | Wood-plastics composites (WPC) Characterisation of WPC products |
| 16/30332917 DC : 0 | BS EN 13915 - PREFABRICATED GYPSUM PLASTERBOARD PANELS WITH A CELLULAR PAPERBOARD CORE - DEFINITIONS, REQUIREMENTS AND TEST METHODS |
| BS ISO 25762 : 2009 | PLASTICS - GUIDANCE ON THE ASSESSMENT OF THE FIRE CHARACTERISTICS AND FIRE PERFORMANCE OF FIBRE-REINFORCED POLYMER COMPOSITES |
| UNE-EN 15037-5:2013 | Precast concrete products - Beam-and-block floor systems - Part 5: Lightweight blocks for simple formwork |
| PREN 438-6 : DRAFT 2014 | HIGH-PRESSURE DECORATIVE (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 6: CLASSIFICATION AND SPECIFICATIONS FOR EXTERIOR-GRADE COMPACT LAMINATES OF THICKNESS 2 MM AND GREATER |
| BS EN 15501:2013 | Thermal insulation products for building equipment and industrial installations. Factory made expanded perlite (EP) and exfoliated vermiculite (EV) products. Specification |
| 04/30113504 DC : DRAFT MAY 2004 | BS EN 14933 - LIGHT WEIGHT FILL AND INSULATION PRODUCTS FOR CIVIL ENGINEERING APPLICATIONS - FACTORY MADE PRODUCTS OF EXPANDED POLYSTYRENE (EPS) - SPECIFICATION |
| UNE-EN 15651-2:2017 | Sealants for non-structural use in joints in buildings and pedestrian walkways - Part 2: Sealants for glazing |
| UNE-EN 14315-1:2013 | Thermal insulating products for buildings. In-situ formed sprayed rigid polyurethane foam (PUR) products. Part 1: Specification for the rigid foam spray system before installation |
| UNE-EN 15102:2008 | Decorative wallcoverings - Roll and panel form products |
| UNI EN 1013 : 2015 | LIGHT TRANSMITTING SINGLE SKIN PROFILED PLASTICS SHEETS FOR INTERNAL AND EXTERNAL ROOFS, WALLS AND CEILINGS - REQUIREMENTS AND TEST METHODS |
| UNE-EN 15501:2017 | Thermal insulation products for building equipment and industrial installations - Factory made expanded perlite (EP) and exfoliated vermiculite (EV) products - Specification |
| UNE-CEN/TS 115-4:2016 | Safety of escalators and moving walks - Part 4: Interpretations related to EN 115 family of standards |
| 03/310127 DC : DRAFT JUNE 2003 | EN 14716 - STRETCHED CEILINGS - REQUIREMENTS AND TEST METHODS |
| PREN 13166 : DRAFT 2010 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE PHENOLIC FOAM (PF) PRODUCTS - SPECIFICATION |
| PREN 494 : DRAFT 2010 | FIBRE-CEMENT PROFILED SHEETS AND FITTINGS - PRODUCT SPECIFICATION AND TEST METHODS |
| DIN EN 14313:2016-03 | THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - FACTORY MADE POLYETHYLENE FOAM (PEF) PRODUCTS - SPECIFICATION |
| DIN EN 14305:2016-03 | THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - FACTORY MADE CELLULAR GLASS (CG) PRODUCTS - SPECIFICATION |
| UNE-EN 15101-1:2015 | Thermal insulation products for buildings - In-situ formed loose fill cellulose (LFCI) products - Part 1: Specification for the products before installation |
| UNE-EN 15266:2008 | Stainless steel pliable corrugated tubing kits in buildings for gas with an operating pressure up to 0,5 bar |
| PREN 13964 : DRAFT 2013 | SUSPENDED CEILINGS - REQUIREMENTS AND TEST METHODS |
| I.S. EN 14064-1:2010 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - IN-SITU FORMED LOOSEFILL MINERAL WOOL (MW) PRODUCTS - PART 1: SPECIFICATION FOR THE LOOSE-FILL PRODUCTS BEFORE INSTALLATION |
| BS EN 15651-1:2017 | Sealants for non-structural use in joints in buildings and pedestrian walkways Sealants for facade elements |
| I.S. EN 14318-1:2013 | THERMAL INSULATING PRODUCTS FOR BUILDINGS - IN-SITU FORMED DISPENSED RIGID POLYURETHANE (PUR) AND POLYISOCYANURATE (PIR) FOAM PRODUCTS - PART 1: SPECIFICATION FOR THE RIGID FOAM DISPENSED SYSTEM BEFORE INSTALLATION |
| UNE-EN 16755:2018 | Durability of reaction to fire performance - Classes of fire-retardant treated wood products in interior and exterior end use applications |
| I.S. EN 16153:2013 | LIGHT TRANSMITTING FLAT MULTIWALL POLYCARBONATE (PC) SHEETS FOR INTERNAL AND EXTERNAL USE IN ROOFS, WALLS AND CEILINGS - REQUIREMENTS AND TEST METHODS |
| I.S. EN 15534-1:2014 | COMPOSITES MADE FROM CELLULOSE-BASED MATERIALS AND THERMOPLASTICS (USUALLY CALLED WOOD-POLYMER COMPOSITES (WPC) OR NATURAL FIBRE COMPOSITES (NFC)) - PART 1: TEST METHODS FOR CHARACTERISATION OF COMPOUNDS AND PRODUCTS |
| I.S. EN 15228:2009 | STRUCTURAL TIMBER - STRUCTURAL TIMBER PRESERVATIVE TREATED AGAINST BIOLOGICAL ATTACK |
| BS EN 115-1:2017 | Safety of escalators and moving walks Construction and installation |
| I.S. EN 16069:2012 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE PRODUCTS OF POLYETHYLENE FOAM (PEF) - SPECIFICATION |
| I.S. EN 14303:2015 | THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - FACTORY MADE MINERAL WOOL (MW) PRODUCTS - SPECIFICATION |
| BS EN 14313 : 2009 | THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - FACTORY MADE POLYETHYLENE FOAM (PEF) PRODUCTS - SPECIFICATION |
| 16/30313668 DC : 0 | BS EN 14064-1 - THERMAL INSULATION PRODUCTS FOR BUILDINGS - IN-SITU FORMED LOOSE-FILL MINERAL WOOL (MW) PRODUCTS - PART 1: SPECIFICATION FOR THE LOOSE-FILL PRODUCTS BEFORE INSTALLATION |
| 14/30297465 DC : 0 | BS EN 15014 - PLASTICS PIPING SYSTEMS - BURIED AND ABOVE GROUND PIPING COMPONENTS FOR WATER UNDER PRESSURE - REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR PIPES AND FITTINGS |
| I.S. EN 15651-3:2017 | SEALANTS FOR NON-STRUCTURAL USE IN JOINTS IN BUILDINGS AND PEDESTRIAN WALKWAYS - PART 3: SEALANTS FOR SANITARY JOINTS |
| DIN EN 14064-1:2010-06 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - IN-SITU FORMED LOOSE-FILL MINERAL WOOL (MW) PRODUCTS - PART 1: SPECIFICATION FOR THE LOOSE-FILL PRODUCTS BEFORE INSTALLATION |
| 17/30353879 DC : 0 | BS EN 17104 - THERMOPLASTICS RIGID PROTECTIVE WALLCOVERING PANELS FOR INTERNAL USE IN BUILDINGS - PERFORMANCE CHARACTERISTICS |
| 17/30362692 DC : 0 | BS EN 598 - COATED AND LINED DUCTILE IRON PIPES, FITTINGS AND THEIR JOINTS FOR SEWERAGE AND DRAINAGE APPLICATIONS - PRODUCTS CHARACTERISTICS AND TEST AND ASSESSMENT METHODS |
| PREN 15651-3 : DRAFT 2012 | SEALANTS FOR NON-STRUCTURAL USE IN JOINTS IN BUILDINGS AND PEDESTRIAN WALKWAYS - PART 3: SEALANTS FOR SANITARY JOINTS |
| PREN 1504-3 : DRAFT 2015 | PRODUCTS AND SYSTEMS FOR THE PROTECTION AND REPAIR OF CONCRETE STRUCTURES - DEFINITIONS, REQUIREMENTS, QUALITY CONTROL AND AVCP - PART 3: REPAIR CONCRETE AND MORTARS |
| DIN EN 16724:2016-03 | THERMAL INSULATION PRODUCTS FOR BUILDING APPLICATIONS - INSTRUCTIONS FOR MOUNTING AND FIXING FOR DETERMINATION OF THE REACTION TO FIRE TESTING OF EXTERNAL THERMAL INSULATION COMPOSITE SYSTEMS (ETICS) |
| S.R. CEN TS 15534-1:2007 | WOOD-PLASTICS COMPOSITES (WPC) - PART 1: TEST METHODS FOR CHARACTERISATION OF WPC MATERIALS AND PRODUCTS |
| S.R. CEN/TS 15679:2007 | THERMAL MODIFIED TIMBER - DEFINITIONS AND CHARACTERISTICS |
| I.S. EN 14307:2015 | THERMAL INSULATION PRODUCTS FOR BUILDING EQUIPMENT AND INDUSTRIAL INSTALLATIONS - FACTORY MADE EXTRUDED POLYSTYRENE FOAM (XPS) PRODUCTS - SPECIFICATION |
| I.S. EN 15283-2:2008 | GYPSUM BOARDS WITH FIBROUS REINFORCEMENT - DEFINITIONS, REQUIREMENTS AND TEST METHODS - PART 2: GYPSUM FIBRE BOARDS |
| DIN EN ISO 15791-1:2014-05 | Plastics - Development and use of intermediate-scale fire tests for plastics products - Part 1: General guidance (ISO 15791-1:2014) |
| DIN EN 13859-2:2014-07 | FLEXIBLE SHEETS FOR WATERPROOFING - DEFINITIONS AND CHARACTERISTICS OF UNDERLAYS - PART 2: UNDERLAYS FOR WALLS |
| DIN EN 490:2012-01 | CONCRETE ROOFING TILES AND FITTINGS FOR ROOF COVERING AND WALL CLADDING - PRODUCT SPECIFICATIONS |
| DIN EN 520:2009-12 | Gypsum plasterboards - Definitions, requirements and test methods (includes Amendment A1:2009) |
| UNE-EN 13964:2016 | Suspended ceilings - Requirements and test methods |
| 13/30277762 DC : 0 | BS EN 60695-8-2 IEC 60695-8-2 ED 1.0 - FIRE HAZARD TESTING - PART 8-2: HEAT RELEASE - SUMMARY AND RELEVANCE OF TEST METHODS |
| UNE-EN 438-3:2016 | High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (Usually called Laminates) - Part 3: Classification and specifications for laminates less than 2 mm thick intended for bonding to supporting substrates |
| BS EN 13238:2010 | Reaction to fire tests for building products. Conditioning procedures and general rules for selection of substrates |
| BS EN 13170 : 2012 | THERMAL INSULATION PRODUCTS FOR BUILDINGS - FACTORY MADE PRODUCTS OF EXPANDED CORK (ICB) - SPECIFICATION |
| BS EN 14915 : 2013 | SOLID WOOD PANELLING AND CLADDING - CHARACTERISTICS, EVALUATION OF CONFORMITY AND MARKING |
| PD IEC/TR 60695-8-2:2008 | Fire hazard testing Heat release. Summary and relevance of test methods |
| BS EN 490 : 2011 | CONCRETE ROOFING TILES AND FITTINGS FOR ROOF COVERING AND WALL CLADDING - PRODUCT SPECIFICATIONS |
| BS EN 14934:2007 | Thermal insulation and light weight fill products for civil engineering applications. Factory made products of extruded polystyrene foam (XPS). Specification |
| BS EN 13859-1:2014 | Flexible sheets for waterproofing. Definitions and characteristics of underlays Underlays for discontinuous roofing |
| BS EN 14081-1:2016 | Timber structures. Strength graded structural timber with rectangular cross section General requirements |
| DIN EN 15651-3:2017-07 | SEALANTS FOR NON-STRUCTURAL USE IN JOINTS IN BUILDINGS AND PEDESTRIAN WALKWAYS - PART 3: SEALANTS FOR SANITARY JOINTS |
| EN 13170:2012+A1:2015 | Thermal insulation products for buildings - Factory made products of expanded cork (ICB) - Specification |
| EN 13169:2012+A1:2015 | Thermal insulation products for buildings - Factory made expanded perlite board (EPB) products - Specification |
| DIN EN 491:2011-11 | Concrete roofing tiles and fittings for roof covering and wall cladding - Test methods |
| EN 13167:2012+A1:2015 | Thermal insulation products for buildings - Factory made cellular glass (CG) products - Specification |
| DIN EN 14474:2005-03 | Precast concrete products - Concrete with wood-chips as aggregate - Requirements and test methods; German version EN 14474:2004 |
| CEN/TS 15534-3:2007 | Wood-plastics composites (WPC) - Part 3: Characterisation of WPC products |
| DIN EN 14934:2007-12 | Thermal insulation and light weight fill products for civil engineering applications - Factory made products of extruded polystyrene foam (XPS) - Specification |
| DIN EN 544:2011-09 | Bitumen shingles with mineral and/or synthetic reinforcements - Product specification and test methods |
| CEN/TS 15447:2006 | Mounting and fixing in reaction to fire tests under the Construction Products Directive |
| DIN EN 14915:2013-12 | SOLID WOOD PANELLING AND CLADDING - CHARACTERISTICS, REQUIREMENTS AND MARKING |
| CEN/TS 15117:2005 | Guidance on direct and extended application |
| CEN/TS 15912:2012 | Durability of reaction to fire performance - Classes of fire-retardant treated wood-based product in interior and exterior end use applications |
| DIN EN 490:2017-04 | Concrete roofing tiles and fittings for roof covering and wall cladding - Product specifications (includes Amendment :2017) |
| EN 50399 : 2011 AMD 1 2016 | COMMON TEST METHODS FOR CABLES UNDER FIRE CONDITIONS - HEAT RELEASE AND SMOKE PRODUCTION MEASUREMENT ON CABLES DURING FLAME SPREAD TEST - TEST APPARATUS, PROCEDURES, RESULTS |
| EN 13165:2012+A2:2016 | Thermal insulation products for buildings - Factory made rigid polyurethane foam (PU) products - Specification |
| EN 60695-8-1:2017 | Fire hazard testing - Part 8-1: Heat release - General guidance |
| UNE-EN 14915:2013 | Solid wood panelling and cladding - Characteristics, evaluation of conformity and marking |
| UNE-EN 16153:2013 | Light transmitting flat multiwall polycarbonate (PC) sheets for internal and external use in roofs, walls and ceilings - Requirements and test methods |
| UNE-EN 14351-1:2006 | Windows and doors - Product standard, performance characteristics - Part 1: Windows and external pedestrian doorsets without resistance to fire and/or smoke leakage characteristics |
| UNE-EN 13162:2013+A1:2015 | Thermal insulation products for buildings - Factory made mineral wool (MW) products - Specification |
| ISO 5725-1:1994 | Accuracy (trueness and precision) of measurement methods and results — Part 1: General principles and definitions |
| ISO 13943:2017 | Fire safety — Vocabulary |
| EN 13238:2010 | Reaction to fire tests for building products - Conditioning procedures and general rules for selection of substrates |
| AS 1735.5.1:2019 | Lifts, escalators and moving walks Safety of escalators and moving walks - Construction and installation (EN 115-1:2017, MOD) |
| EN 60584-1:2013 | Thermocouples - Part 1: EMF specifications and tolerances |
| AS 1735.5.4:2019 | Lifts, escalators and moving walks Safety of escalators and moving walks - Interpretations related to AS 1735.5 series of standards (CEN/TS 115-4:2015, MOD) |
| EN ISO 13943:2017 | Fire safety - Vocabulary (ISO 13943:2017) |
| ISO 5725-2:1994 | Accuracy (trueness and precision) of measurement methods and results Part 2: Basic method for the determination of repeatability and reproducibility of a standard measurement method |
| ISO 3966:2008 | Measurement of fluid flow in closed conduits Velocity area method using Pitot static tubes |
| IEC 60584-1:2013 | Thermocouples - Part 1: EMF specifications and tolerances |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.