DIN EN ISO 9227:2017-07
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Corrosion tests in artificial atmospheres - Salt spray tests (ISO 9227:2017)
Hardcopy , PDF
03-08-2023
English, German
07-01-2017
Important note : All end users must be registered with an Account prior to user licenses being assigned.
National foreword
National Annex NA (informative) - Bibliography
European foreword
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Principle
5 Test solutions
6 Apparatus
7 Method for evaluating cabinet corrosivity
8 Test specimens
9 Arrangement of the test specimens
10 Operating conditions
11 Duration of tests
12 Treatment of test specimens after test
13 Evaluation of results
14 Test report
Annex A (informative) - Example schematic diagram of
one possible design of spray
cabinet with means for optional
treating fog exhaust and drain
Annex B (informative) - Complementary method for evaluating
cabinet corrosivity using zinc reference
specimens
Annex C (normative) - Preparation of specimens with organic
coatings for testing
Annex D (normative) - Required supplementary information
for testing test specimens with organic
coatings
Bibliography
Defines the apparatus, the reagents and the procedure to be used in conducting the neutral salt spray (NSS), acetic acid salt spray (AASS) and copper-accelerated acetic acid salt spray (CASS) tests for assessment of the corrosion resistance of metallic materials, with or without permanent or temporary corrosion protection.
| DocumentType |
Standard
|
| Pages |
29
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| ISO 9227:2017 | Identical |
| EN ISO 9227:2017 | Identical |
| DIN 984:2013-04 | Retaining rings with lugs (internal circlips) for use in bores |
| DIN EN ISO 10683:2001-02 | FASTENERS - NON-ELECTROLYTICALLY APPLIED ZINC FLAKE COATINGS (ISO 10683:2014) |
| DIN EN ISO 19598:2017-04 | METALLIC COATINGS - ELECTROPLATED COATINGS OF ZINC AND ZINC ALLOYS ON IRON OR STEEL WITH SUPPLEMENTARY CR(6)-FREE TREATMENT (ISO 19598:2016) |
| DIN EN ISO 11439:2013-09 | Gas cylinders - High pressure cylinders for the on-board storage of natural gas as a fuel for automotive vehicles (ISO 11439:2013) |
| DIN EN ISO 17268:2017-03 | Gaseous hydrogen land vehicle refuelling connection devices (ISO 17268:2012) |
| ISO 1514:2016 | Paints and varnishes — Standard panels for testing |
| ISO 7599:2010 | Anodizing of aluminium and its alloys General specifications for anodic oxidation coatings on aluminium |
| ISO 8993:2010 | Anodizing of aluminium and its alloys Rating system for the evaluation of pitting corrosion Chart method |
| ISO 4623-2:2016 | Paints and varnishes Determination of resistance to filiform corrosion Part 2: Aluminium substrates |
| ISO 8994:2011 | Anodizing of aluminium and its alloys Rating system for the evaluation of pitting corrosion Grid method |
| ISO 2808:2007 | Paints and varnishes Determination of film thickness |
| DIN EN ISO 8407 E : 2014 | CORROSION OF METALS AND ALLOYS - REMOVAL OF CORROSION PRODUCTS FROM CORROSION TEST SPECIMENS (ISO 8407:2009) |
| ISO 4628-8:2012 | Paints and varnishes — Evaluation of degradation of coatings — Designation of quantity and size of defects, and of intensity of uniform changes in appearance — Part 8: Assessment of degree of delamination and corrosion around a scribe or other artificial defect |
| ISO 4628-4:2016 | Paints and varnishes Evaluation of degradation of coatings Designation of quantity and size of defects, and of intensity of uniform changes in appearance Part 4: Assessment of degree of cracking |
| ISO 15528:2013 | Paints, varnishes and raw materials for paints and varnishes Sampling |
| ISO 1456:2009 | Metallic and other inorganic coatings — Electrodeposited coatings of nickel, nickel plus chromium, copper plus nickel and of copper plus nickel plus chromium |
| ISO 4628-3:2016 | Paints and varnishes — Evaluation of degradation of coatings — Designation of quantity and size of defects, and of intensity of uniform changes in appearance — Part 3: Assessment of degree of rusting |
| DIN EN ISO 8044:2015-12 | CORROSION OF METALS AND ALLOYS - BASIC TERMS AND DEFINITIONS (ISO 8044:2015) |
| ISO 17872:2007 | Paints and varnishes Guidelines for the introduction of scribe marks through coatings on metallic panels for corrosion testing |
| ISO 4628-5:2016 | Paints and varnishes — Evaluation of degradation of coatings — Designation of quantity and size of defects, and of intensity of uniform changes in appearance — Part 5: Assessment of degree of flaking |
| ISO 4628-1:2016 | Paints and varnishes Evaluation of degradation of coatings Designation of quantity and size of defects, and of intensity of uniform changes in appearance Part 1: General introduction and designation system |
| DIN EN ISO 1514:1997-09 | PAINTS AND VARNISHES - STANDARD PANELS FOR TESTING (ISO 1514:2016) |
| ISO 8044:2015 | Corrosion of metals and alloys Basic terms and definitions |
| ISO 4527:2003 | Metallic coatings Autocatalytic (electroless) nickel-phosphorus alloy coatings Specification and test methods |
| ISO 3696:1987 | Water for analytical laboratory use — Specification and test methods |
| ISO 8407:2009 | Corrosion of metals and alloys Removal of corrosion products from corrosion test specimens |
| ISO 1513:2010 | Paints and varnishes Examination and preparation of test samples |
| ISO 10289:1999 | Methods for corrosion testing of metallic and other inorganic coatings on metallic substrates Rating of test specimens and manufactured articles subjected to corrosion tests |
| ISO 3613:2010 | Metallic and other inorganic coatings Chromate conversion coatings on zinc, cadmium, aluminium-zinc alloys and zinc-aluminium alloys Test methods |
| DIN ISO 3696:1991-06 | WATER FOR ANALYTICAL LABORATORY USE - SPECIFICATION AND TEST METHODS |
| ISO 4628-2:2016 | Paints and varnishes Evaluation of degradation of coatings Designation of quantity and size of defects, and of intensity of uniform changes in appearance Part 2: Assessment of degree of blistering |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.