DIN EN ISO 472:2013-06
Current
Current
The latest, up-to-date edition.
PLASTICS - VOCABULARY (ISO 472:2013)
Available format(s)
Hardcopy , PDF
Published date
01-01-2013
Important note : All end users must be registered with an Account prior to user licenses being assigned.| DevelopmentNote |
DRAFT AMD 1 issued in September 2016. (09/2016)
|
| DocumentType |
Standard
|
| Pages |
471
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Current
|
| Standards | Relationship |
| ISO 472:2013 | Identical |
| EN ISO 472:2013 | Identical |
| DIN EN ISO 16014-5:2012-10 | PLASTICS - DETERMINATION OF AVERAGE MOLECULAR MASS AND MOLECULAR MASS DISTRIBUTION OF POLYMERS USING SIZE-EXCLUSION CHROMATOGRAPHY - PART 5: METHOD USING LIGHT-SCATTERING DETECTION (ISO 16014-5:2012) |
| DIN EN ISO 877-1:2016-09 (Draft) | PLASTICS - METHODS OF EXPOSURE TO SOLAR RADIATION - PART 1: GENERAL GUIDANCE |
| DIN EN ISO 11357-4 E : 2014 | PLASTICS - DIFFERENTIAL SCANNING CALORIMETRY (DSC) - PART 4: DETERMINATION OF SPECIFIC HEAT CAPACITY (ISO 11357-4:2014) |
| DIN EN ISO 3451-1:2008-11 | PLASTICS - DETERMINATION OF ASH - PART 1: GENERAL METHODS |
| DIN EN ISO 11357-6:2013-04 | PLASTICS - DIFFERENTIAL SCANNING CALORIMETRY (DSC) - PART 6: DETERMINATION OF OXIDATION INDUCTION TIME (ISOTHERMAL OIT) AND OXIDATION INDUCTION TEMPERATURE (DYNAMIC OIT) (ISO 11357-6:2008) |
| DIN 55657:2016-08 | Paints and varnishes - Test method for evaluation of elastic adhesives on coatings by peel test, peel strength test and tensile lap-shear strength test with additional stress by condensation test or cataplasm storage |
| DIN EN ISO 11337:2011-04 | Plastics - Polyamides - Determination of -caprolactam and -laurolactam by gas chromatography (ISO 11337:2010) |
| DIN 16831-2:2003-05 | PIPE FITTINGS AND JOINT ASSEMBLIES FOR POLYBUTENE PRESSURE PIPES - TYPE PB 125 - PART 2: DIMENSIONS OF INJECTION-MOULDED TEES FOR SOCKET WELDING |
| DIN EN ISO 20568-1:2017-10 | PLASTICS - FLUOROPOLYMER DISPERSIONS AND MOULDING AND EXTRUSION MATERIALS - PART 1: DESIGNATION SYSTEM AND BASIS FOR SPECIFICATIONS (ISO 20568-1:2017) |
| DIN EN ISO 9163:2005-07 | Textile glass - Rovings - Manufacture of test specimens and determination of tensile strength of impregnated rovings (ISO 9163:2005); German version EN ISO 9163:2005 |
| DIN EN ISO 306:2014-03 | Plastics - Thermoplastic materials - Determination of Vicat softening temperature (VST) (ISO 306:2013) |
| DIN EN ISO 6401:2008-12 | Plastics - Poly(vinyl chloride) - Determination of residual vinyl chloride monomer - Gas-chromatographic method (ISO 6401:2008) |
| DIN EN ISO 1043-3:2017-03 | PLASTICS - SYMBOLS AND ABBREVIATED TERMS - PART 3: PLASTICIZERS (ISO 1043-3:2016) |
| DIN EN ISO 20568-2:2017-10 | PLASTICS - FLUOROPOLYMER DISPERSIONS AND MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 20568-2:2017) |
| DIN EN ISO 10927:2011-07 | PLASTICS - DETERMINATION OF THE MOLECULAR MASS AND MOLECULAR MASS DISTRIBUTION OF POLYMER SPECIES BY MATRIX-ASSISTED LASER DESORPTION/IONIZATION TIME-OF-FLIGHT MASS SPECTROMETRY (MALDI-TOF-MS) |
| DIN EN ISO 11357-7:2015-12 | Plastics - Differential scanning calorimetry (DSC) - Part 7: Determination of crystallization kinetics (ISO 11357-7:2015); German version EN ISO 11357-7:2015 |
| DIN EN ISO 25762:2012-04 | Plastics - Guidance on the assessment of the fire characteristics and fire performance of fibre-reinforced polymer composites (ISO 25762:2009) |
| DIN EN ISO 11357-2:2014-07 | PLASTICS - DIFFERENTIAL SCANNING CALORIMETRY (DSC) - PART 2: DETERMINATION OF GLASS TRANSITION TEMPERATURE AND GLASS TRANSITION STEP HEIGHT (ISO 11357-2:2013) |
| DIN EN ISO 16664:2016-07 (Draft) | GAS ANALYSIS - HANDLING OF CALIBRATION GASES AND GAS MIXTURES - GUIDELINES (ISO 16664:2017) |
| DIN EN ISO 16396-2:2017-07 | Plastics - Polyamide (PA) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 16396-2:2017) |
| DIN EN ISO 1874-2:2013-03 | PLASTICS - POLYAMIDE (PA) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 1874-2:2012) |
| DIN EN ISO 15023-1:2016-03 (Draft) | PLASTICS - POLY(VINYL ALCOHOL) (PVAL) MATERIALS - PART 1: DESIGNATION SYSTEM AND BASIS FOR SPECIFICATIONS (ISO 15023-1:2017) |
| DIN EN ISO 877-1:2011-03 | Plastics - Methods of exposure to solar radiation - Part 1: General guidance (ISO 877-1:2009) |
| DIN EN ISO 22007-6:2015-05 | PLASTICS - DETERMINATION OF THERMAL CONDUCTIVITY AND THERMAL DIFFUSIVITY - PART 6: COMPARATIVE METHOD FOR LOW THERMAL CONDUCTIVITIES USING A TEMPERATURE-MODULATION TECHNIQUE (ISO 22007-6:2014) |
| DIN EN ISO 16396-1:2015-05 | Plastics - Polyamide (PA) moulding and extrusion materials - Part 1: Designation system, marking of products and basis for specifications (ISO 16396-1:2015) |
| DIN EN ISO 11357-3:2013-04 | PLASTICS - DIFFERENTIAL SCANNING CALORIMETRY (DSC) - PART 3: DETERMINATION OF TEMPERATURE AND ENTHALPY OF MELTING AND CRYSTALLIZATION (ISO 11357-3:2011) |
| DIN EN ISO 1452-1:2010-04 | Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: General (ISO 1452-1:2009) |
| DIN EN ISO 1183-1:2013-04 | PLASTICS - METHODS FOR DETERMINING THE DENSITY OF NON-CELLULAR PLASTICS - PART 1: IMMERSION METHOD, LIQUID PYKNOMETER METHOD AND TITRATION METHOD (ISO 1183-1:2012) |
| DIN EN ISO 15877-1:2011-03 | Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 1: General (ISO 15877-1:2009 + AMD 1:2010) |
| DIN EN ISO 21003-1:2008-11 | MULTILAYER PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS INSIDE BUILDINGS - PART 1: GENERAL |
| DIN EN ISO 22007-3:2012-04 | Plastics - Determination of thermal conductivity and thermal diffusivity - Part 3: Temperature wave analysis method (ISO 22007-3:2008) |
| DIN EN ISO 11357-4:2014-10 | Plastics - Differential scanning calorimetry (DSC) - Part 4: Determination of specific heat capacity (ISO 11357-4:2014) |
| DIN EN ISO 11358-1:2014-10 | Plastics - Thermogravimetry (TG) of polymers - Part 1: General principles (ISO 11358-1:2014) |
| DIN EN ISO 1133-2:2012-03 | Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics - Part 2: Method for materials sensitive to time-temperature history and/or moisture (ISO 1133-2:2011) |
| DIN EN ISO 6721-1:2011-08 | PLASTICS - DETERMINATION OF DYNAMIC MECHANICAL PROPERTIES - PART 1: GENERAL PRINCIPLES |
| DIN EN ISO 15494:2016-03 | PLASTICS PIPING SYSTEMS FOR INDUSTRIAL APPLICATIONS - POLYBUTENE (PB), POLYETHYLENE (PE), POLYETHYLENE OF RAISED TEMPERATURE RESISTANCE (PE-RT), CROSSLINKED POLYETHYLENE (PE-X), POLYPROPYLENE (PP) - METRIC SERIES FOR SPECIFICATIONS FOR COMPONENTS AND THE SYSTEM (ISO 15494:2015) |
| DIN EN ISO 2078:2016-05 | Textile glass - Yarns - Designation (ISO 2078:1993 + Amd 1:2015) (includes Amendment :2015) |
| DIN EN ISO 1043-1:2016-09 | PLASTICS - SYMBOLS AND ABBREVIATED TERMS - PART 1: BASIC POLYMERS AND THEIR SPECIAL CHARACTERISTICS (ISO 1043-1:2011 + AMD.1:2016) |
| DIN EN ISO 1043-3:2015-09 (Draft) | PLASTICS - SYMBOLS AND ABBREVIATED TERMS - PART 3: PLASTICIZERS (ISO 1043-3:2016) |
| DIN EN ISO 15750-3:2008-09 | Packaging - Steel drums - Part 3: Inserted flange-type closure systems (ISO 15750-3:2002) |
| DIN 16831-7:2004-02 | Pipe fittinings and joint assemblies for polybutene pressure pipes - Type PB 125 - Part 7: Dimensions of bushings, flanges and sealing elements for socket welding |
| DIN EN ISO 20568-1:2015-07 (Draft) | PLASTICS - FLUOROPOLYMER DISPERSIONS AND MOULDING AND EXTRUSION MATERIALS - PART 1: DESIGNATION SYSTEM AND BASIS FOR SPECIFICATIONS (ISO 20568-1:2017) |
| DIN EN ISO 22391-1:2010-04 | Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) - Part 1: General (ISO 22391-1:2009) |
| DIN EN ISO 20568-2:2015-07 (Draft) | PLASTICS - FLUOROPOLYMER DISPERSIONS AND MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 20568-2:2017) |
| DIN 16831-1:2003-05 | PIPE FITTINGS AND JOINT ASSEMBLIES FOR POLYBUTENE PRESSURE PIPES - TYPE PB 125 - PART 1: DIMENSIONS OF INJECTION-MOULDED ELBOWS FOR SOCKET WELDING |
| DIN 16831-4:2003-05 | PIPE FITTINGS AND JOINT ASSEMBLIES FOR POLYBUTENE PRESSURE PIPES - TYPE PB 125 - PART 4: DIMENSIONS OF INJECTION-MOULDED REDUCERS FOR SOCKET WELDING |
| DIN 16831-3:2003-05 | PIPE FITTINGS AND JOINT ASSEMBLIES FOR POLYBUTENE PRESSURE PIPES - TYPE PB 125 - PART 3: DIMENSIONS OF INJECTION-MOULDED SOCKETS AND CAPS FOR SOCKET WELDING |
| DIN 16831-6:2003-06 | PIPE FITTINGS AND JOINT ASSEMBLIES FOR POLYBUTENE PRESSURE PIPES - TYPE PB 125 - PART 6: DIMENSIONS OF FITTINGS FOR RESISTANCE WELDING |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.