DIN EN ISO 20753:2014-07
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PLASTICS - TEST SPECIMENS (ISO 20753:2008)
Available format(s)
Hardcopy , PDF
Language(s)
German
Published date
01-01-2014
Superseded date
02-05-2019
Superseded by
US$98.58
Excluding Tax where applicable
National foreword
National Annex NA (informative) - Bibliography
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Preparation of test specimens
5 Types of test specimen and their dimensions
6 Report on preparation of test specimens
Annex A (informative) - Recommended applications
for multipurpose test specimens or parts
thereof
Annex B (normative) - Designation system for
test specimens
Bibliography
This standard is included in DIN Handbook KUNSTSTOFFE BAND 1.
| DevelopmentNote |
DRAFT 2017 issued in June 2017. (06/2017)
|
| DocumentType |
Standard
|
| Pages |
23
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| ISO 20753:2008 | Identical |
| EN ISO 20753:2014 | Identical |
| BS EN ISO 20753:2014 | Equivalent |
| DIN EN ISO 17855-2:2016-06 | PLASTICS - POLYETHYLENE (PE) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 17855-2:2016) |
| DIN EN ISO 16012:2016-02 | PLASTICS - DETERMINATION OF LINEAR DIMENSIONS OF TEST SPECIMENS (ISO 16012:2015) |
| DIN EN ISO 306:2014-03 | Plastics - Thermoplastic materials - Determination of Vicat softening temperature (VST) (ISO 306:2013) |
| DIN EN ISO 19069-2:2016-07 | PLASTICS - POLYPROPYLENE (PP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 19069-2:2016) |
| DIN EN ISO 16396-2:2017-07 | Plastics - Polyamide (PA) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 16396-2:2017) |
| DIN EN ISO 20028-2:2015-08 (Draft) | PLASTICS - THERMOPLASTIC POLYESTER (TP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 20028-2:2017) |
| DIN EN ISO 294-1:2017-09 | PLASTICS - INJECTION MOULDING OF TEST SPECIMENS OF THERMOPLASTIC MATERIALS - PART 1: GENERAL PRINCIPLES, AND MOULDING OF MULTIPURPOSE AND BAR TEST SPECIMENS (ISO 294-1:2017) |
| DIN HDBK KUNSTSTOFFE BAND 1 : 2016 | HANDBUCH KUNSTSTOFFE - BAND 1 - MECHANISCHE UND THERMISCHE EIGENSCHAFTEN - PRUEFNORMEN |
| IEC 60112:2003+AMD1:2009 CSV | Method for the determination of the proof and the comparative tracking indices of solid insulating materials |
| ISO 4589-3:2017 | Plastics — Determination of burning behaviour by oxygen index — Part 3: Elevated-temperature test |
| ISO 10350-2:2011 | Plastics — Acquisition and presentation of comparable single-point data — Part 2: Long-fibre-reinforced plastics |
| DIN EN ISO 294-5:2015-08 (Draft) | PLASTICS - INJECTION MOULDING OF TEST SPECIMENS OF THERMOPLASTIC MATERIALS - PART 5: PREPARATION OF STANDARD SPECIMENS FOR INVESTIGATING ANISOTROPY (ISO 294-5:2017) |
| ISO 22088-1:2006 | Plastics — Determination of resistance to environmental stress cracking (ESC) — Part 1: General guidance |
| DIN EN ISO 179-2:2012-06 | PLASTICS - DETERMINATION OF CHARPY IMPACT PROPERTIES - PART 2: INSTRUMENTED IMPACT TEST (ISO 179-2:1997 + AMD.1:2011) |
| DIN EN ISO 22088-6:2009-10 | Plastics - Determination of resistance to environmental stress cracking (ESC) - Part 6: Slow strain rate method (ISO 22088-6:2006) |
| ISO 293:2004 | Plastics — Compression moulding of test specimens of thermoplastic materials |
| ISO 3167:2014 | Plastics — Multipurpose test specimens |
| VDE 0303-6 : 2007 COR 1 2010 | ELECTRICAL INSULATING MATERIALS - DETERMINATION OF ELECTROLYTIC CORROSION CAUSED BY INSULATING MATERIALS - TEST METHODS |
| ISO 294-5:2017 | Plastics — Injection moulding of test specimens of thermoplastic materials — Part 5: Preparation of standard specimens for investigating anisotropy |
| ISO 11403-3:2014 | Plastics — Acquisition and presentation of comparable multipoint data — Part 3: Environmental influences on properties |
| DIN EN 60426 : 2007 COR 1 2010 | ELECTRICAL INSULATING MATERIALS - DETERMINATION OF ELECTROLYTIC CORROSION CAUSED BY INSULATING MATERIALS - TEST METHODS |
| ISO 294-3:2002 | Plastics — Injection moulding of test specimens of thermoplastic materials — Part 3: Small plates |
| ISO 22088-2:2006 | Plastics — Determination of resistance to environmental stress cracking (ESC) — Part 2: Constant tensile load method |
| DIN EN ISO 10350-1:2016-08 (Draft) | PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE SINGLE-POINT DATA - PART 1: MOULDING MATERIALS (ISO 10350-1:2017) |
| ISO 295:2004 | Plastics — Compression moulding of test specimens of thermosetting materials |
| ISO 10350-1:2017 | Plastics — Acquisition and presentation of comparable single-point data — Part 1: Moulding materials |
| ISO 22088-5:2006 | Plastics — Determination of resistance to environmental stress cracking (ESC) — Part 5: Constant tensile deformation method |
| ISO 2039-1:2001 | Plastics — Determination of hardness — Part 1: Ball indentation method |
| ISO 10724-1:1998 | Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 1: General principles and moulding of multipurpose test specimens |
| ISO 8256:2004 | Plastics — Determination of tensile-impact strength |
| ISO 11359-2:1999 | Plastics — Thermomechanical analysis (TMA) — Part 2: Determination of coefficient of linear thermal expansion and glass transition temperature |
| VDE 0303-11 : 2010 | METHOD FOR THE DETERMINATION OF THE PROOF AND THE COMPARATIVE TRACKING INDICES OF SOLID INSULATING MATERIALS |
| DIN EN 60112 : 2010 | METHOD FOR THE DETERMINATION OF THE PROOF AND THE COMPARATIVE TRACKING INDICES OF SOLID INSULATING MATERIALS |
| DIN EN ISO 1183-1:2013-04 | PLASTICS - METHODS FOR DETERMINING THE DENSITY OF NON-CELLULAR PLASTICS - PART 1: IMMERSION METHOD, LIQUID PYKNOMETER METHOD AND TITRATION METHOD (ISO 1183-1:2012) |
| ISO 75-2:2013 | Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite |
| DIN EN ISO 294-2:2006-05 | PLASTICS - INJECTION MOULDING OF TEST SPECIMENS OF THERMOPLASTIC MATERIALS - SMALL TENSILE BARS |
| ISO 527-2:2012 | Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics |
| DIN EN ISO 4589-2:2016-03 (Draft) | PLASTICS - DETERMINATION OF BURNING BEHAVIOUR BY OXYGEN INDEX - PART 2: AMBIENT-TEMPERATURE TEST (ISO 4589-2:2017) |
| DIN EN ISO 899-2:2015-06 | Plastics - Determination of creep behaviour - Part 2: Flexural creep by three-point loading (ISO 899-2:2003 + Amd.1:2015) (includes Amendment A1:2015) |
| ISO 2039-2:1987 | Plastics — Determination of hardness — Part 2: Rockwell hardness |
| ISO 11403-2:2012 | Plastics — Acquisition and presentation of comparable multipoint data — Part 2: Thermal and processing properties |
| DIN EN ISO 4589-3:2016-03 (Draft) | PLASTICS - DETERMINATION OF BURNING BEHAVIOUR BY OXYGEN INDEX - PART 3: ELEVATED-TEMPERATURE TEST (ISO 4589-3:2017) |
| DIN EN ISO 180:2013-08 | PLASTICS - DETERMINATION OF IZOD IMPACT STRENGTH (ISO 180:2000 + AMD.1:2006 + AMD.2:2013) |
| ISO 180:2000 | Plastics — Determination of Izod impact strength |
| ISO 22088-3:2006 | Plastics — Determination of resistance to environmental stress cracking (ESC) — Part 3: Bent strip method |
| DIN EN ISO 295:2004-05 | Plastics - Compression moulding of test specimens of thermosetting materials (ISO 295:2004); German version EN ISO 295:2004 |
| DIN EN ISO 294-3:2003-12 | PLASTICS - INJECTION MOULDING OF TEST SPECIMENS OF THERMOPLASTIC MATERIALS - PART 3: SMALL PLATES |
| ISO 294-2:1996 | Plastics — Injection moulding of test specimens of thermoplastic materials — Part 2: Small tensile bars |
| ISO 899-2:2003 | Plastics — Determination of creep behaviour — Part 2: Flexural creep by three-point loading |
| ISO 1183-1:2012 | Plastics — Methods for determining the density of non-cellular plastics — Part 1: Immersion method, liquid pyknometer method and titration method |
| ISO 1183-2:2004 | Plastics — Methods for determining the density of non-cellular plastics — Part 2: Density gradient column method |
| ISO 1183-3:1999 | Plastics — Methods for determining the density of non-cellular plastics — Part 3: Gas pyknometer method |
| ISO 604:2002 | Plastics — Determination of compressive properties |
| DIN EN ISO 11403-1:2014-09 | Plastics - Acquisition and presentation of comparable multipoint data - Part 1: Mechanical properties (ISO 11403-1:2014) |
| ISO 179-1:2010 | Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test |
| DIN EN ISO 2039-2:2000-01 | Plastics - Determination of hardness - Part 2: Rockwell hardness (ISO 2039-2:1987); German version EN ISO 2039-2:1999 |
| IEC 60426:2007 | Electrical insulating materials - Determination of electrolytic corrosion caused by insulating materials - Test methods |
| DIN EN ISO 294-1:2017-09 | PLASTICS - INJECTION MOULDING OF TEST SPECIMENS OF THERMOPLASTIC MATERIALS - PART 1: GENERAL PRINCIPLES, AND MOULDING OF MULTIPURPOSE AND BAR TEST SPECIMENS (ISO 294-1:2017) |
| ISO 306:2013 | Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST) |
| ISO 22088-4:2006 | Plastics — Determination of resistance to environmental stress cracking (ESC) — Part 4: Ball or pin impression method |
| DIN EN ISO 293:2005-10 | Plastics - Compression moulding of test specimens of thermoplastic materials (ISO 293:2004) |
| ISO 294-1:2017 | Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens |
| ISO 22088-6:2006 | Plastics — Determination of resistance to environmental stress cracking (ESC) — Part 6: Slow strain rate method |
| ISO 4589-2:2017 | Plastics — Determination of burning behaviour by oxygen index — Part 2: Ambient-temperature test |
| ISO 2818:1994 | Plastics — Preparation of test specimens by machining |
| ISO 899-1:2017 | Plastics — Determination of creep behaviour — Part 1: Tensile creep |
| ISO 11403-1:2014 | Plastics — Acquisition and presentation of comparable multipoint data — Part 1: Mechanical properties |
| DIN EN ISO 11403-3:2014-09 | Plastics - Acquisition and presentation of comparable multipoint data - Part 3: Environmental influences on properties (ISO 11403-3:2014) |
| ASTM D 1822 : 2013 : REDLINE | Standard Test Method for Tensile-Impact Energy to Break Plastics and Electrical Insulating Materials |
| DIN EN ISO 10724-1:2002-04 | PLASTICS - INJECTION MOULDING OF TEST SPECIMENS OF THERMOSETTING POWDER MOULDING COMPOUNDS (PMCS) - PART 1: GENERAL PRINCIPLES AND MOULDING OF MULTIPURPOSE TEST SPECIMENS |
| ISO 178:2010 | Plastics — Determination of flexural properties |
| DIN EN ISO 22088-5:2009-10 | Plastics - Determination of resistance to environmental stress cracking (ESC) - Part 5: Constant tensile deformation method (ISO 22088-5:2006) |
| DIN EN ISO 75-2:2013-08 | PLASTICS - DETERMINATION OF TEMPERATURE OF DEFLECTION UNDER LOAD - PART 2: PLASTICS AND EBONITE (ISO 75-2:2013) |
| DIN EN ISO 10350-2:2011-06 | PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE SINGLE-POINT DATA - PART 2: LONG-FIBRE-REINFORCED PLASTICS |
| DIN EN ISO 604:2003-12 | PLASTICS - DETERMINATION OF COMPRESSIVE PROPERTIES |
| DIN EN ISO 3167:2014-11 | PLASTICS - MULTIPURPOSE TEST SPECIMENS (ISO 3167:2014) |
| ISO 868:2003 | Plastics and ebonite — Determination of indentation hardness by means of a durometer (Shore hardness) |
Summarise
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : All end users must be registered with an Account prior to user licenses being assigned.