DIN EN ISO 14910-2:2013-06
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
PLASTICS - THERMOPLASTIC POLYESTER/ESTER AND POLYETHER/ESTER ELASTOMERS FOR MOULDING AND EXTRUSION - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 14910-2:2013)
Available format(s)
Hardcopy , PDF
Superseded date
03-07-2021
Language(s)
English, German
Published date
01-01-2013
Important note : All end users must be registered with an Account prior to user licenses being assigned.
National foreword
National Annex NA (informative) - Bibliography
Foreword
Introduction
1 Scope
2 Normative references
3 Preparation of test specimens
4 Conditioning of test specimens
5 Determination of properties
Bibliography
Describes the methods of preparation of test specimens and the standard test methods to be used in determining the properties of thermoplastic polyester/ester and polyether/ester moulding and extrusion materials.
| DocumentType |
Standard
|
| Pages |
24
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Superseded
|
| Standards | Relationship |
| EN ISO 14910-2:2013 | Identical |
| I.S. EN ISO 14910-2:2013 | Identical |
| NBN EN ISO 14910-2 : 2013 | Identical |
| UNI EN ISO 14910-2 : 2013 | Identical |
| SN EN ISO 14910-2:2013 | Identical |
| ISO 14910-2:2013 | Identical |
| NEN EN ISO 14910-2 : 2013 + COR 2016 | Identical |
| ONORM EN ISO 14910-2 : 2013 | Identical |
| BS EN ISO 14910-2:2013 | Identical |
| NF EN ISO 14910-2 : 2013 | Identical |
| UNE-EN ISO 14910-2:2014 | Identical |
| NS EN ISO 14910-2 : 2013 | Identical |
| DIN EN ISO 14910-1:2013-06 | PLASTICS - THERMOPLASTIC POLYESTER/ESTER AND POLYETHER/ESTER ELASTOMERS FOR MOULDING AND EXTRUSION - PART 1: DESIGNATION SYSTEM AND BASIS FOR SPECIFICATION (ISO 14910-1:2013) |
| IEC 60243-1:2013 | Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies |
| IEC 60112:2003+AMD1:2009 CSV | Method for the determination of the proof and the comparative tracking indices of solid insulating materials |
| ISO 22007-3:2008 | Plastics Determination of thermal conductivity and thermal diffusivity Part 3: Temperature wave analysis method |
| DIN EN ISO 15512:2017-03 | PLASTICS - DETERMINATION OF WATER CONTENT (ISO 15512:2016) |
| DIN EN ISO 11357-4 E : 2014 | PLASTICS - DIFFERENTIAL SCANNING CALORIMETRY (DSC) - PART 4: DETERMINATION OF SPECIFIC HEAT CAPACITY (ISO 11357-4:2014) |
| ISO 3167:2014 | Plastics Multipurpose test specimens |
| ISO 22007-4:2017 | Plastics — Determination of thermal conductivity and thermal diffusivity — Part 4: Laser flash method |
| ISO 974:2000 | Plastics Determination of the brittleness temperature by impact |
| DIN EN ISO 14910-1:2013-06 | PLASTICS - THERMOPLASTIC POLYESTER/ESTER AND POLYETHER/ESTER ELASTOMERS FOR MOULDING AND EXTRUSION - PART 1: DESIGNATION SYSTEM AND BASIS FOR SPECIFICATION (ISO 14910-1:2013) |
| IEC 60250:1969 | Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including metre wavelengths |
| DIN IEC 60093 : 1993 | METHODS OF TEST FOR INSULATING MATERIALS FOR ELECTRICAL PURPOSES; VOLUME RESISTIVITY AND SURFACE RESISTIVITY OF SOLID ELECTRICAL INSULATING MATERIALS |
| DIN EN ISO 899-1:2015-06 | PLASTICS - DETERMINATION OF CREEP BEHAVIOUR - PART 1: TENSILE CREEP (ISO 899-1:2017) |
| ISO 815-1:2014 | Rubber, vulcanized or thermoplastic Determination of compression set Part 1: At ambient or elevated temperatures |
| DIN IEC 60695-11-10 : DRAFT 2010 | FIRE HAZARD TESTING - PART 11-10: TEST FLAMES - 50 W HORIZONTAL AND VERTICAL FLAME TEST METHODS |
| ISO 10350-1:2017 | Plastics — Acquisition and presentation of comparable single-point data — Part 1: Moulding materials |
| DIN EN 60243-1 : 2014 | ELECTRIC STRENGTH OF INSULATING MATERIALS - TEST METHODS - PART 1: TESTS AT POWER FREQUENCIES (IEC 60243-1:2013) |
| ISO 8256:2004 | Plastics — Determination of tensile-impact strength |
| ISO 11359-2:1999 | Plastics Thermomechanical analysis (TMA) Part 2: Determination of coefficient of linear thermal expansion and glass transition temperature |
| DIN EN ISO 527-2:2012-06 | Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics (ISO 527-2:2012) |
| ISO 34-1:2015 | Rubber, vulcanized or thermoplastic Determination of tear strength Part 1: Trouser, angle and crescent test pieces |
| DIN EN 60112 : 2010 | METHOD FOR THE DETERMINATION OF THE PROOF AND THE COMPARATIVE TRACKING INDICES OF SOLID INSULATING MATERIALS |
| ISO 75-2:2013 | Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite |
| ISO 527-2:2012 | Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics |
| ISO 11357-3:2011 | Plastics Differential scanning calorimetry (DSC) Part 3: Determination of temperature and enthalpy of melting and crystallization |
| ISO 11357-4:2014 | Plastics Differential scanning calorimetry (DSC) Part 4: Determination of specific heat capacity |
| ISO 294-4:2001 | Plastics Injection moulding of test specimens of thermoplastic materials Part 4: Determination of moulding shrinkage |
| IEC 60093:1980 | Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials |
| IEC 60695-11-10:2013 | Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods |
| ISO 1183-1:2012 | Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method |
| ISO 1183-2:2004 | Plastics Methods for determining the density of non-cellular plastics Part 2: Density gradient column method |
| ISO 1183-3:1999 | Plastics Methods for determining the density of non-cellular plastics Part 3: Gas pyknometer method |
| ISO 14910-1:2013 | Plastics Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion Part 1: Designation system and basis for specification |
| ISO 179-1:2010 | Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test |
| ISO 15512:2016 | Plastics Determination of water content |
| ISO 62:2008 | Plastics Determination of water absorption |
| ISO 306:2013 | Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST) |
| ISO 294-1:2017 | Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens |
| ISO 37:2017 | Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties |
| ISO 4589-2:2017 | Plastics — Determination of burning behaviour by oxygen index — Part 2: Ambient-temperature test |
| ISO 22007-2:2015 | Plastics Determination of thermal conductivity and thermal diffusivity Part 2: Transient plane heat source (hot disc) method |
| ISO 1133-2:2011 | Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 2: Method for materials sensitive to time-temperature history and/or moisture |
| ISO 899-1:2017 | Plastics — Determination of creep behaviour — Part 1: Tensile creep |
| ISO 178:2010 | Plastics Determination of flexural properties |
| ISO 868:2003 | Plastics and ebonite — Determination of indentation hardness by means of a durometer (Shore hardness) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.