DIN EN ISO 14405-2:2012-03
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - DIMENSIONAL TOLERANCING - PART 2: DIMENSIONS OTHER THAN LINEAR SIZES (ISO 14405-2:2011)
Hardcopy , PDF
06-01-2019
German, English
01-01-2012
Important note : All end users must be registered with an Account prior to user licenses being assigned.
National foreword
National Annex NA (informative) - Bibliography
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Principles and rules for indication of dimensions
and related tolerances
5 Units used in drawings for dimensions
6 Indication of tolerances for linear and angular dimensions
7 Illustrations of ambiguous +/- tolerancing vs. unambiguous
geometrical tolerancing
8 Angular tolerancing
Annex A (informative) - Explanations and examples of the
ambiguity caused by using +/- tolerances for dimensions
other than linear size
Annex B (informative) - Relation to the GPS matrix model
Bibliography
Provides the use of geometrical tolerancing for dimensions that are not linear sizes to avoid the ambiguity that the use of +/- tolerances on these dimensions causes.
| DevelopmentNote |
DRAFT AMD 1 issued in July 2017. (07/2017)
|
| DocumentType |
Standard
|
| Pages |
31
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| EN ISO 14405-2:2011 | Identical |
| ISO 14405-2:2011 | Identical |
| DIN EN ISO 2538-2:2015-01 | Geometrical product specifications (GPS) - Wedges - Part 2: Dimensioning and tolerancing (ISO 2538-2:2014) |
| DIN CEN ISO/TS 8062-2;DIN SPEC 91184:2014-03 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - DIMENSIONAL AND GEOMETRICAL TOLERANCES FOR MOULDED PARTS - PART 2: RULES (ISO/TS 8062-2:2013) |
| DIN EN ISO 14405-3:2013-08 (Draft) | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - DIMENSIONAL TOLERANCING - PART 3: ANGULAR SIZES (ISO 14405-3:2016) |
| DIN 16742:2013-10 | PLASTICS MOULDED PARTS - TOLERANCES AND ACCEPTANCE CONDITIONS |
| DIN EN ISO 10451:2010-11 | Dentistry - Contents of technical file for dental implant systems (ISO 10451:2010) |
| ISO/TR 14638:1995 | Geometrical product specification (GPS) Masterplan |
| ISO 8015:2011 | Geometrical product specifications (GPS) Fundamentals Concepts, principles and rules |
| ISO 5459:2011 | Geometrical product specifications (GPS) — Geometrical tolerancing — Datums and datum systems |
| DIN EN ISO 286-1:2010-11 | GEOMETRICAL PRODUCT SPECIFICATION (GPS) - ISO CODE SYSTEM FOR TOLERANCES ON LINEAR SIZES - PART 1: BASIS OF TOLERANCES, DEVIATIONS AND FITS |
| DIN EN ISO 14660-1:1999-11 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - GEOMETRIC FEATURES - PART 1: GENERAL TERMS AND DEFINITIONS |
| ISO 2692:2014 | Geometrical product specifications (GPS) Geometrical tolerancing Maximum material requirement (MMR), least material requirement (LMR) and reciprocity requirement (RPR) |
| ISO 1101:2017 | Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out |
| DIN EN ISO 8015:2011-09 | Geometrical product specifications (GPS) - Fundamentals - Concepts, principles and rules (ISO 8015:2011) |
| ISO 14253-1:2017 | Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 1: Decision rules for verifying conformity or nonconformity with specifications |
| ISO 8062-3:2007 | Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 3: General dimensional and geometrical tolerances and machining allowances for castings |
| ISO 3040:2016 | Geometrical product specifications (GPS) Dimensioning and tolerancing Cones |
| ISO 17450-1:2011 | Geometrical product specifications (GPS) — General concepts — Part 1: Model for geometrical specification and verification |
| ISO 81714-1:2010 | Design of graphical symbols for use in the technical documentation of products Part 1: Basic rules |
| DIN EN ISO 17450-2:2013-04 | Geometrical product specifications (GPS) - General concepts - Part 2: Basic tenets, specifications, operators, uncertainties and ambiguities (ISO 17450-2:2012) |
| ISO 2538:1998 | Geometrical Product Specifications (GPS) Series of angles and slopes on prisms |
| ISO 286-1:2010 | Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 1: Basis of tolerances, deviations and fits |
| DIN EN ISO 17450-1:2012-04 | Geometrical product specifications (GPS) - General concepts - Part 1: Model for geometrical specification and verification (ISO 17450-1:2011) |
| ISO 14660-2:1999 | Geometrical Product Specifications (GPS) Geometrical features Part 2: Extracted median line of a cylinder and a cone, extracted median surface, local size of an extracted feature |
| ISO 129-1:2004 | Technical drawings Indication of dimensions and tolerances Part 1: General principles |
| ISO 14660-1:1999 | Geometrical Product Specifications (GPS) Geometrical features Part 1: General terms and definitions |
| ISO 14405-1:2016 | Geometrical product specifications (GPS) — Dimensional tolerancing — Part 1: Linear sizes |
| ISO 14253-2:2011 | Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 2: Guidance for the estimation of uncertainty in GPS measurement, in calibration of measuring equipment and in product verification |
| ISO 13715:2017 | Technical product documentation — Edges of undefined shape — Indication and dimensioning |
| ISO 5458:1998 | Geometrical Product Specifications (GPS) Geometrical tolerancing Positional tolerancing |
| ISO/R 1938:1971 | ISO system of limits and fits Part II : Inspection of plain workpieces |
| DIN EN ISO 14405-1:2017-07 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - DIMENSIONAL TOLERANCING - PART 1: LINEAR SIZES (ISO 14405-1:2016) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.